Ashkan Roshan-Zamir
Research Subjects
Ashkan Roshan-Zamir has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Hae-Woong Yang
Department of Electrical and Computer Engineering, Texas A&M University, College Station, TX, USA
5 shared publications- Samuel Palermo
Department of Electrical and Computer Engineering, Texas A&M University, College Station, TX, USA
5 shared publications Osama Elhadidy
QUALCOMM Inc., San Diego, CA, USA
3 shared publications- Ankur Kumar
Department of Electrical and Computer Engineering, Texas A&M University, College Station, TX, USA
2 shared publications - Takayuki Iwai
Analog and Mixed Signal Center, Electrical and Computer Engineering Department, Texas A&M University, College Station, TX 77843 USA. He is now with Kioxia Corporation, Kawasaki 212-0013, Japan
2 shared publications - Yang-Hang Fan
Analog and Mixed-Signal Center, Texas A&M University, College Station, TX, USA
2 shared publications
Latest Publications
- 13 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 55 (2) , 439-451
A 32-Gb/s Simultaneous Bidirectional Source-Synchronous Transceiver With Adaptive Echo Cancellation Techniques
Increased bandwidth per pin is necessary to support the growing data throughput in mobile systems. This article presents a low-power simultaneous bidirectional (SBD) transceiver employing a novel voltage-mode driver with a resistor-transconductance (R-gm) hybrid subtractor to enable concurrent transmission and reception of data on a single differential channel. A finite impulse response (FIR) filter-based adaptive echo cancellation system that cancels both near- and far-end echoes allows for the support of a wide range of channels, while a continuous-time linear equalizer (CTLE) efficiently compensates for channel loss. The quarter-rate source-synchronous transceiver utilizes a low-complexity phase interpolator-based clock and data alignment system to set the optimum data sampling point. Fabricated in 28-nm CMOS, the 32-Gb/s SBD transceiver achieves 1.83 mW/Gb/s and compensates 10.2-dB loss at a bit error rate (BER) <10⁻¹².
- 13 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 55 (2) , 439-451
A 32-Gb/s Simultaneous Bidirectional Source-Synchronous Transceiver With Adaptive Echo Cancellation Techniques
Increased bandwidth per pin is necessary to support the growing data throughput in mobile systems. This article presents a low-power simultaneous bidirectional (SBD) transceiver employing a novel voltage-mode driver with a resistor-transconductance (R-gm) hybrid subtractor to enable concurrent transmission and reception of data on a single differential channel. A finite impulse response (FIR) filter-based adaptive echo cancellation system that cancels both near- and far-end echoes allows for the support of a wide range of channels, while a continuous-time linear equalizer (CTLE) efficiently compensates for channel loss. The quarter-rate source-synchronous transceiver utilizes a low-complexity phase interpolator-based clock and data alignment system to set the optimum data sampling point. Fabricated in 28-nm CMOS, the 32-Gb/s SBD transceiver achieves 1.83 mW/Gb/s and compensates 10.2-dB loss at a bit error rate (BER) <10⁻¹².
- 18 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (3) , 672-684
A 56-Gb/s PAM4 Receiver With Low-Overhead Techniques for Threshold and Edge-Based DFE FIR- and IIR-Tap Adaptation in 65-nm CMOS
This paper presents a four-level pulse amplitude modulation (PAM4) quarter-rate receiver that efficiently compensates for moderate channel loss in a robust manner through background adaptation of the receiver thresholds and equalization taps. The front-end utilizes an input single-stage continuous-time linear equalizer (CTLE) to boost the main cursor and relax the pre-cursor cancellation requirement, requiring only a 2-tap pre-cursor feed-forward equalizer (FFE) on the transmitter side. A 2-tap decision feedback equalizer (DFE) follows that includes one finite impulse response (FIR) tap and one infinite impulse response (IIR) tap to cancel first post-cursor and long-tail inter-symbol interference (ISI), respectively. In addition to the per-slice main three data samplers, a single error sampler is utilized for background threshold control and an edge-based sampler performs both phase-locked loop (PLL)-based clock and data recovery (CDR) phase detection and generates information for background DFE tap adaptation. Fabricated in general purpose (GP) 65-nm CMOS, the 56-Gb/s receiver achieves 4.63 mW/Gb/s and compensates for up to 20.8-dB loss at a bit error rate (BER) <; 10 -12 when operated with a 2-tap FFE transmitter.
- 18 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (3) , 672-684
A 56-Gb/s PAM4 Receiver With Low-Overhead Techniques for Threshold and Edge-Based DFE FIR- and IIR-Tap Adaptation in 65-nm CMOS
This paper presents a four-level pulse amplitude modulation (PAM4) quarter-rate receiver that efficiently compensates for moderate channel loss in a robust manner through background adaptation of the receiver thresholds and equalization taps. The front-end utilizes an input single-stage continuous-time linear equalizer (CTLE) to boost the main cursor and relax the pre-cursor cancellation requirement, requiring only a 2-tap pre-cursor feed-forward equalizer (FFE) on the transmitter side. A 2-tap decision feedback equalizer (DFE) follows that includes one finite impulse response (FIR) tap and one infinite impulse response (IIR) tap to cancel first post-cursor and long-tail inter-symbol interference (ISI), respectively. In addition to the per-slice main three data samplers, a single error sampler is utilized for background threshold control and an edge-based sampler performs both phase-locked loop (PLL)-based clock and data recovery (CDR) phase detection and generates information for background DFE tap adaptation. Fabricated in general purpose (GP) 65-nm CMOS, the 56-Gb/s receiver achieves 4.63 mW/Gb/s and compensates for up to 20.8-dB loss at a bit error rate (BER) <; 10 -12 when operated with a 2-tap FFE transmitter.
- 1 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 261-264
A low-power dual-mode 20-Gb/s NRZ and 28-Gb/s PAM-4 voltage-mode transmitter
A dual-mode NRZ/PAM-4 differential low-swing voltage-mode transmitter employs a quarter-rate output multiplexing architecture for low-power operation. In NRZ mode, 2-tap feedforward equalization is realized with analog replica-bias tap control that is configurable in high-performance controlled-impedance or energy-efficient impedance-modulated settings. This analog control also allows for efficient generation of the middle levels in PAM-4 operation. Fabricated in GP 65nm CMOS, the transmitter supports an output swing range of 100-400mVPpd with up to 12dB of equalization in NRZ mode and achieves energy efficiencies of 1.48 and 0.91pJ/b at 20-Gb/s NRZ and 28-Gb/s PAM-4 data rates. Operation in the NRZ energy-efficient impedance-modulation setting allows for power savings of up to 32% relative to the controlled-impedance setting.
- 1 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 261-264
A low-power dual-mode 20-Gb/s NRZ and 28-Gb/s PAM-4 voltage-mode transmitter
A dual-mode NRZ/PAM-4 differential low-swing voltage-mode transmitter employs a quarter-rate output multiplexing architecture for low-power operation. In NRZ mode, 2-tap feedforward equalization is realized with analog replica-bias tap control that is configurable in high-performance controlled-impedance or energy-efficient impedance-modulated settings. This analog control also allows for efficient generation of the middle levels in PAM-4 operation. Fabricated in GP 65nm CMOS, the transmitter supports an output swing range of 100-400mVPpd with up to 12dB of equalization in NRZ mode and achieves energy efficiencies of 1.48 and 0.91pJ/b at 20-Gb/s NRZ and 28-Gb/s PAM-4 data rates. Operation in the NRZ energy-efficient impedance-modulation setting allows for power savings of up to 32% relative to the controlled-impedance setting.
- Open Access
- 13 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 52 (9) , 2430-2447
A Reconfigurable 16/32 Gb/s Dual-Mode NRZ/PAM4 SerDes in 65-nm CMOS
While four-level pulse amplitude modulation (PAM4) standards are emerging to increase bandwidth density, the majority of standards use simple binary non-returnto-zero (NRZ) signaling. This paper presents a dual-mode NRZ/PAM4 serial I/O SerDes which can support both modulations with minimum power and hardware overhead relative to a dedicated PAM4 link. A source-series-terminated transmitter achieves 1.2-V pp output swing and employs lookup table control of a 31-segment output digital-to-analog converter (DAC) to implement 4/2-tap feed-forward equalization in NRZ/PAM4 modes, respectively. Transmitter power is improved with low-overhead analog impedance control in the DAC cells and a quarter-rate serializer based on a tri-state inverter-based mux with dynamic pre-driver gates. The receiver implements an NRZ/PAM4 decision feedback equalizer that employs one finite impulse response and two infinite impulse response taps for first post-cursor and long-tail inter-symbol interference (ISI) cancellation, respectively. First post-cursor ISI cancellation is performed in these comparators to optimize the design's timing, while the remaining ISI taps are subtracted in a preceding current integration summer for improved sensitivity. Fabricated in GP 65-nm CMOS, the transceiver occupies 0.074 mm2 area and achieves 16 Gb/s NRZ and 32 Gb/s PAM4 operation at 10.9 and 5.5 mW/Gb/s while operating over channels with 27.6 and 13.5 dB loss at Nyquist, respectively.
- 13 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 52 (9) , 2430-2447
Open AccessA Reconfigurable 16/32 Gb/s Dual-Mode NRZ/PAM4 SerDes in 65-nm CMOS
While four-level pulse amplitude modulation (PAM4) standards are emerging to increase bandwidth density, the majority of standards use simple binary non-returnto-zero (NRZ) signaling. This paper presents a dual-mode NRZ/PAM4 serial I/O SerDes which can support both modulations with minimum power and hardware overhead relative to a dedicated PAM4 link. A source-series-terminated transmitter achieves 1.2-V pp output swing and employs lookup table control of a 31-segment output digital-to-analog converter (DAC) to implement 4/2-tap feed-forward equalization in NRZ/PAM4 modes, respectively. Transmitter power is improved with low-overhead analog impedance control in the DAC cells and a quarter-rate serializer based on a tri-state inverter-based mux with dynamic pre-driver gates. The receiver implements an NRZ/PAM4 decision feedback equalizer that employs one finite impulse response and two infinite impulse response taps for first post-cursor and long-tail inter-symbol interference (ISI) cancellation, respectively. First post-cursor ISI cancellation is performed in these comparators to optimize the design's timing, while the remaining ISI taps are subtracted in a preceding current integration summer for improved sensitivity. Fabricated in GP 65-nm CMOS, the transceiver occupies 0.074 mm2 area and achieves 16 Gb/s NRZ and 32 Gb/s PAM4 operation at 10.9 and 5.5 mW/Gb/s while operating over channels with 27.6 and 13.5 dB loss at Nyquist, respectively.
- 24 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A 16/32 Gb/s Dual-Mode NRZ/PAM4 SerDes in 65nm CMOS
A dual-mode NRZ/PAM4 SerDes seamlessly supports both modulations with a 1-FIR- and 2-IIR-tap DFE receiver and a 4/2-tap FFE transmitter in NRZ/PAM4 modes, respectively. A source-series-terminated (SST) transmitter employs lookup-table (LUT) control of a 31-segment output DAC to implement FFE equalization in NRZ and PAM4 modes with 1.2Vpp output swing and utilizes low-overhead analog impedance control. Optimization of the quarter-rate transmitter serializer is achieved with a tri-state inverterbased mux with dynamic pre-driver gates. The quarter-rate DFE receiver achieves efficient equalization with 1-FIR tap for the large first post-cursor ISI and 2-IIR taps for long-tail ISI cancellation. Fabricated in GP 65-nm CMOS, the transceiver occupies 0.074 mm2 area and achieves power efficiencies of 10.9 and 5.5 mW/Gbps with 16Gb/s NRZ and 32Gb/s PAM4 data, respectively.
- 24 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A 16/32 Gb/s Dual-Mode NRZ/PAM4 SerDes in 65nm CMOS
A dual-mode NRZ/PAM4 SerDes seamlessly supports both modulations with a 1-FIR- and 2-IIR-tap DFE receiver and a 4/2-tap FFE transmitter in NRZ/PAM4 modes, respectively. A source-series-terminated (SST) transmitter employs lookup-table (LUT) control of a 31-segment output DAC to implement FFE equalization in NRZ and PAM4 modes with 1.2Vpp output swing and utilizes low-overhead analog impedance control. Optimization of the quarter-rate transmitter serializer is achieved with a tri-state inverterbased mux with dynamic pre-driver gates. The quarter-rate DFE receiver achieves efficient equalization with 1-FIR tap for the large first post-cursor ISI and 2-IIR taps for long-tail ISI cancellation. Fabricated in GP 65-nm CMOS, the transceiver occupies 0.074 mm2 area and achieves power efficiencies of 10.9 and 5.5 mW/Gbps with 16Gb/s NRZ and 32Gb/s PAM4 data, respectively.
- 1 June 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. C224-C225
A 32 Gb/s 0.55 mW/Gbps PAM4 1-FIR 2-IIR tap DFE receiver in 65-nm CMOS
A PAM4 serial I/O receiver efficiently implements a decision feedback equalizer (DFE) that employs 1-FIR and 2-IIR taps for first post-cursor and long-tail ISI cancellation, respectively. The use of a single-clock phase two-stage regenerative comparator simplifies the quarter-rate receiver design and allows for sufficient gain to support PAM4 DFE. Optimization of the direct-feedback design's timing is achieved by cancelling the critical first post-cursor multi-level ISI directly at the comparator, while performing the remaining taps' ISI subtraction in a preceding current integration summer for improved sensitivity. Fabricated in GP 65-nm CMOS, the receiver occupies 0.0138 mm2 area and achieves power efficiencies of 0.55 and 0.52 mW/Gbps with 32 Gb/s and 25 Gb/s PAM4 data, respectively.
- 1 June 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. C224-C225
A 32 Gb/s 0.55 mW/Gbps PAM4 1-FIR 2-IIR tap DFE receiver in 65-nm CMOS
A PAM4 serial I/O receiver efficiently implements a decision feedback equalizer (DFE) that employs 1-FIR and 2-IIR taps for first post-cursor and long-tail ISI cancellation, respectively. The use of a single-clock phase two-stage regenerative comparator simplifies the quarter-rate receiver design and allows for sufficient gain to support PAM4 DFE. Optimization of the direct-feedback design's timing is achieved by cancelling the critical first post-cursor multi-level ISI directly at the comparator, while performing the remaining taps' ISI subtraction in a preceding current integration summer for improved sensitivity. Fabricated in GP 65-nm CMOS, the receiver occupies 0.0138 mm2 area and achieves power efficiencies of 0.55 and 0.52 mW/Gbps with 32 Gb/s and 25 Gb/s PAM4 data, respectively.