Michael C. Griffith
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Michael C. Griffith has a total of 74 co-authors. Here are the top co-authors by number of shared publications:
- Jason Maxwell Ingham
Department of Civil and Environmental Engineering University of Auckland Auckland New Zealand
14 shared publications - Hossein Derakhshan
University of Adelaide, Adelaide, Australia
11 shared publications Dmytro Y. Dizhur
University of Auckland, Auckland, New Zealand
3 shared publicationsYasuto Nakamura
3 shared publications- Abdul Hamid Sheikh
School of Architecture and Civil Engineering, The University of Adelaide, Adelaide, SA 5005, Australia
2 shared publications - Deric John Oehlers
School of Civil, Environmental and Mining Engineering, University of Adelaide, South Australia 5005, Australia
2 shared publications
Latest Publications
- 25 March 2020
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 18 (7) , 3383-3400
Simplified calculation of roof accelerations in existing low-rise symmetric unreinforced masonry buildings with flexible diaphragms
- 25 March 2020
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 18 (7) , 3383-3400
Simplified calculation of roof accelerations in existing low-rise symmetric unreinforced masonry buildings with flexible diaphragms
- 16 December 2019
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 49 (3) , 285-300
Seismic fragility assessment of nonstructural components in unreinforced clay brick masonry buildings
Summary: The results of an investigation of the probability of earthquake damage to nonstructural unreinforced masonry (URM) components are presented. The components include parapets, chimneys, and out‐of‐plane loaded facades typical of low‐rise pre‐1940 construction in Australia and New Zealand. The study is based on a street survey of component geometry, in situ data on material strength, and simplified mechanical models. Uncertainties in capacity and demand were quantified based on, respectively, stochastic and deterministic approaches. The damage probabilities were compared with relevant guidelines and empirical damage data from three earthquakes. The study established a link between the qualitative damage states reported in existing guidelines and the quantitative URM component damage states. While some median damage state thresholds correlated well with the data from the guidelines, a larger dispersion value was found in the current study due to the large variations in component properties. Comparisons with empirical data suggest that the developed fragility data provide a realistic estimate of nonstructural component damage that occurred in similar buildings, with a reasonable level of conservatism. The outcome is useful in rapid assessment of the seismic risks due to nonstructural component collapse in URM precincts.
- 16 December 2019
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 49 (3) , 285-300
Seismic fragility assessment of nonstructural components in unreinforced clay brick masonry buildings
Summary: The results of an investigation of the probability of earthquake damage to nonstructural unreinforced masonry (URM) components are presented. The components include parapets, chimneys, and out‐of‐plane loaded facades typical of low‐rise pre‐1940 construction in Australia and New Zealand. The study is based on a street survey of component geometry, in situ data on material strength, and simplified mechanical models. Uncertainties in capacity and demand were quantified based on, respectively, stochastic and deterministic approaches. The damage probabilities were compared with relevant guidelines and empirical damage data from three earthquakes. The study established a link between the qualitative damage states reported in existing guidelines and the quantitative URM component damage states. While some median damage state thresholds correlated well with the data from the guidelines, a larger dispersion value was found in the current study due to the large variations in component properties. Comparisons with empirical data suggest that the developed fragility data provide a realistic estimate of nonstructural component damage that occurred in similar buildings, with a reasonable level of conservatism. The outcome is useful in rapid assessment of the seismic risks due to nonstructural component collapse in URM precincts.
- 1 March 2019
- Published by Elsevier in Composite Structures
- Vol. 212, 43-57
Digital image correlation (DIC) for measurement of strains and displacements in coarse, low volume-fraction FRP composites used in civil infrastructure
- 1 March 2019
- Published by Elsevier in Composite Structures
- Vol. 212, 43-57
Digital image correlation (DIC) for measurement of strains and displacements in coarse, low volume-fraction FRP composites used in civil infrastructure
- 1 September 2018
- Published by Elsevier in Engineering Geology
- Vol. 243, 145-159
Estimating bedrock depth in the case of regolith sites using ambient noise analysis
- 1 September 2018
- Published by Elsevier in Engineering Geology
- Vol. 243, 145-159
Estimating bedrock depth in the case of regolith sites using ambient noise analysis
- 1 March 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 144 (3)
Laboratory Testing of Strengthened Cavity Unreinforced Masonry Walls
An experimental campaign consisting of nine pressure-controlled quasi-static airbag tests on unreinforced masonry (URM) walls and accompanying material testing was completed to investigate methods for seismic retrofit of out-of-plane loaded cavity walls. Three control walls were tested to serve as a baseline for wall strength comparisons: (1) a double-leaf unstrengthened cavity wall; (2) a cavity wall with improved cavity connections; and (3) a single-leaf wall strengthened using a near-surface-mounted (NSM) fiber-reinforced polymer (FRP) strip. The experimental program was concluded by six tests that were conducted on walls strengthened using a NSM FRP strip and having cavity connections in the form of either standard bent metal ties, proprietary helical anchors, or industrial foam. The tests were designed to measure the ability of the different cavity connections to maintain the cavity gap until a ductile wall failure mechanism forms by FRP debonding. Three of the walls were previously damaged by testing in either unstrengthened or FRP-strengthened conditions. These tests were intended to study FRP retrofit effectiveness of precracked walls or the relative ability of different types of cavity connections to resist forces until a global FRP debonding occurs. For each of the six cavity connection configurations, the FRP-strengthening technique was shown to significantly improve the wall strength. The minimum strength increase was 282% compared with that of the control cavity wall. The compiled data are presented followed by general discussions on the design of seismic retrofit for cavity walls.
- 1 March 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 144 (3)
Laboratory Testing of Strengthened Cavity Unreinforced Masonry Walls
An experimental campaign consisting of nine pressure-controlled quasi-static airbag tests on unreinforced masonry (URM) walls and accompanying material testing was completed to investigate methods for seismic retrofit of out-of-plane loaded cavity walls. Three control walls were tested to serve as a baseline for wall strength comparisons: (1) a double-leaf unstrengthened cavity wall; (2) a cavity wall with improved cavity connections; and (3) a single-leaf wall strengthened using a near-surface-mounted (NSM) fiber-reinforced polymer (FRP) strip. The experimental program was concluded by six tests that were conducted on walls strengthened using a NSM FRP strip and having cavity connections in the form of either standard bent metal ties, proprietary helical anchors, or industrial foam. The tests were designed to measure the ability of the different cavity connections to maintain the cavity gap until a ductile wall failure mechanism forms by FRP debonding. Three of the walls were previously damaged by testing in either unstrengthened or FRP-strengthened conditions. These tests were intended to study FRP retrofit effectiveness of precracked walls or the relative ability of different types of cavity connections to resist forces until a global FRP debonding occurs. For each of the six cavity connection configurations, the FRP-strengthening technique was shown to significantly improve the wall strength. The minimum strength increase was 282% compared with that of the control cavity wall. The compiled data are presented followed by general discussions on the design of seismic retrofit for cavity walls.
- Open Access
- 1 August 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Engineering Mechanics
- Vol. 143 (8)
Probabilistic Analysis of Unreinforced Brick Masonry Walls Subjected to Horizontal Bending
Unreinforced masonry walls subjected to out-of-plane horizontal bending can fail by two alternate modes: stepped failure along the brick-mortar bond, or line failure cutting directly through the bricks. Because of random variations in material properties throughout a panel and the tendency for failure to occur across the weaker elements, vertical cracks will generally exhibit a combination of the two modes. This paper develops a pair of analytical methodologies that treat this phenomenon using a stochastic approach. The first part deals with calculating the ultimate moment capacity by allowing for the weakening effect associated with the mixed (stepped and line) mode of failure. This effect is quantified in terms of strength-reduction factors for mean and characteristic (0.05 quantile) values of strength, which may be applied toward generic ultimate strength design. The second part deals with estimating the relative probability of each failure mode and the probability distribution for the relative proportions of each failure mode along a crack. This is of particular relevance to seismic performance because the two failure modes lead to significantly different postcracking behavior.
- 1 August 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Engineering Mechanics
- Vol. 143 (8)
Open AccessProbabilistic Analysis of Unreinforced Brick Masonry Walls Subjected to Horizontal Bending
Unreinforced masonry walls subjected to out-of-plane horizontal bending can fail by two alternate modes: stepped failure along the brick-mortar bond, or line failure cutting directly through the bricks. Because of random variations in material properties throughout a panel and the tendency for failure to occur across the weaker elements, vertical cracks will generally exhibit a combination of the two modes. This paper develops a pair of analytical methodologies that treat this phenomenon using a stochastic approach. The first part deals with calculating the ultimate moment capacity by allowing for the weakening effect associated with the mixed (stepped and line) mode of failure. This effect is quantified in terms of strength-reduction factors for mean and characteristic (0.05 quantile) values of strength, which may be applied toward generic ultimate strength design. The second part deals with estimating the relative probability of each failure mode and the probability distribution for the relative proportions of each failure mode along a crack. This is of particular relevance to seismic performance because the two failure modes lead to significantly different postcracking behavior.
- Open Access
- 30 September 2016
- Published by New Zealand Society for Earthquake Engineering in Bulletin of the New Zealand Society for Earthquake Engineering
- Vol. 49 (3)
Equivalent frame modelling of an unreinforced masonry building with flexible diaphragms
A case study was conducted to investigate the applicability of the equivalent frame modelling for the nonlinear time-history analysis of unreinforced masonry buildings with flexible diaphragms. The dynamic responses calculated from the equivalent frame models were compared against shake table test results of a full-scale two-storey stone masonry building. The investigated modelling approach reflected the simplifications commonly assumed for the global analysis of buildings; namely, considering the diaphragms to behave elastically and neglecting the stiffness and strength contributions of the out-of-plane responding walls. The sensitivity of the analysis to different idealisations of the equivalent frame, as well as to the diaphragm stiffness values, were also investigated. Discussions are provided on the accuracies and limitations of the investigated modelling approach, which may serve as a useful guidance for practical application.
- 30 September 2016
- Published by New Zealand Society for Earthquake Engineering in Bulletin of the New Zealand Society for Earthquake Engineering
- Vol. 49 (3)
Open AccessEquivalent frame modelling of an unreinforced masonry building with flexible diaphragms
A case study was conducted to investigate the applicability of the equivalent frame modelling for the nonlinear time-history analysis of unreinforced masonry buildings with flexible diaphragms. The dynamic responses calculated from the equivalent frame models were compared against shake table test results of a full-scale two-storey stone masonry building. The investigated modelling approach reflected the simplifications commonly assumed for the global analysis of buildings; namely, considering the diaphragms to behave elastically and neglecting the stiffness and strength contributions of the out-of-plane responding walls. The sensitivity of the analysis to different idealisations of the equivalent frame, as well as to the diaphragm stiffness values, were also investigated. Discussions are provided on the accuracies and limitations of the investigated modelling approach, which may serve as a useful guidance for practical application.
- 22 September 2016
- Published by Taylor & Francis in International Journal of Architectural Heritage
SIMULATION OF SHAKE TABLE TESTS ON OUT-OF-PLANE MASONRY BUILDINGS. PART (I): DISPLACEMENT-BASED APPROACH USING SIMPLE FAILURE MECHANISMS
A displacement-based (DB) assessment procedure was used to predict the results of shake table testing of two unreinforced masonry buildings, one made of clay bricks and the other of stone masonry. The simple buildings were subject to an acceleration history, with the maximum acceleration incrementally increased until a collapse mechanism formed. Using the test data, the accuracy and limitations of a displacement-based procedure to predict the maximum building displacements are studied. In particular, the displacement demand was calculated using the displacement response spectrum corresponding to the actual shake table earthquake motion that caused wall collapse (or near collapse). This approach was found to give displacements in reasonable agreement with the wall’s displacement capacity.
- 22 September 2016
- Published by Taylor & Francis in International Journal of Architectural Heritage
SIMULATION OF SHAKE TABLE TESTS ON OUT-OF-PLANE MASONRY BUILDINGS. PART (I): DISPLACEMENT-BASED APPROACH USING SIMPLE FAILURE MECHANISMS
A displacement-based (DB) assessment procedure was used to predict the results of shake table testing of two unreinforced masonry buildings, one made of clay bricks and the other of stone masonry. The simple buildings were subject to an acceleration history, with the maximum acceleration incrementally increased until a collapse mechanism formed. Using the test data, the accuracy and limitations of a displacement-based procedure to predict the maximum building displacements are studied. In particular, the displacement demand was calculated using the displacement response spectrum corresponding to the actual shake table earthquake motion that caused wall collapse (or near collapse). This approach was found to give displacements in reasonable agreement with the wall’s displacement capacity.
- 1 May 2016
- Published by Elsevier in Construction and Building Materials
- Vol. 111, 251-261
Manufacturing ultra-high performance concrete utilising conventional materials and production methods
- 1 May 2016
- Published by Elsevier in Construction and Building Materials
- Vol. 111, 251-261
Manufacturing ultra-high performance concrete utilising conventional materials and production methods
- 30 October 2015
- Published by Taylor & Francis in Australian Journal of Structural Engineering
- Vol. 16 (4) , 262-272
Feasibility of rammed earth constructions for seismic loads in Australia
Out-of-plane bending tests were conducted to determine whether rammed earth (RE) walls, designed to satisfy the thermal performance requirements specified by the Building Code of Australia, will satisfy the seismic loading requirements. A 2.4 m tall by 1.2 m wide full-scale insulated RE wall comprised of two 175 mm thick leaves separated by a 50-mm thick layer of insulation, was tested and the results were compared to that of a solid 300-mm thick RE wall. Both walls remained stable after cracking up to displacement of 50 mm (over 20% of wall thickness). The acceleration necessary to generate the initial forces to cause cracking was over 0.77 g, well in excess of the maximum design accelerations for face-loaded masonry walls in Australia. Furthermore, it was found that the flexural strength of the insulated cavity RE wall was simply the sum of the flexural strengths of the two leaves and that both walls after reaching their peak strength and cracking at mid-height responded as two rigid rocking blocks.
- 30 October 2015
- Published by Taylor & Francis in Australian Journal of Structural Engineering
- Vol. 16 (4) , 262-272
Feasibility of rammed earth constructions for seismic loads in Australia
Out-of-plane bending tests were conducted to determine whether rammed earth (RE) walls, designed to satisfy the thermal performance requirements specified by the Building Code of Australia, will satisfy the seismic loading requirements. A 2.4 m tall by 1.2 m wide full-scale insulated RE wall comprised of two 175 mm thick leaves separated by a 50-mm thick layer of insulation, was tested and the results were compared to that of a solid 300-mm thick RE wall. Both walls remained stable after cracking up to displacement of 50 mm (over 20% of wall thickness). The acceleration necessary to generate the initial forces to cause cracking was over 0.77 g, well in excess of the maximum design accelerations for face-loaded masonry walls in Australia. Furthermore, it was found that the flexural strength of the insulated cavity RE wall was simply the sum of the flexural strengths of the two leaves and that both walls after reaching their peak strength and cracking at mid-height responded as two rigid rocking blocks.