Modesto Amundarain
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Modesto Amundarain has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Izaskun Garrido
University of the Basque Country (UPV/EHU)
9 shared publications Mikel Alberdi
9 shared publicationsM. Alberdi
Department of Automatic Control and Systems Engineering. EUITI Bilbao. University of the Basque Country (UPV/EHU), Rafael Moreno 3, 48013. Spain
7 shared publicationsAitor J. Garrido
Automatic Control Group, Dept. of Automatic Control and Systems Engineering, EUITI de Bilbao, University of the Basque Country (UPV/EHU), Bilbao, Spain
6 shared publicationsIzaskun Garrido
Automatic Control Group, Department of Automatic Control and Systems Engineering, EUITI Bilbao, University of the Basque Country (UPV/EHU), Plaza de la Casilla, 3, 48012, Spain
5 shared publications- Manuel De la Sen
Institute of Research and Development of Processes IIDP, University of the Basque Country, Campus of Leioa, 48940 Leioa, Spain
5 shared publications
Latest Publications
- 1 December 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 29-34
Sensor control for an Oscillating Water Column plant
The Oscillating Water Column concept consists of two key elements, a turbine located in a pneumatic energy collection chamber and a doubly fed induction generator that converts energy extracted by the turbine into a form that can be returned to the network. Since the turbo-generator control requires the rotor angular velocity, removing the rotor speed sensor simplifies the hardware, with the consequent reduction in installation and maintenance costs which is even more relevant in the rough working sea conditions. In this particular case, a Luenberger based observer is considered and the effectiveness of the proposed control is shown by numerical simulations. Comparing these results with those obtained using a traditional speed sensor, it is shown that the proposed solution provides better performance since it allows a more reliable and robust performance of the plant.
- 1 December 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 29-34
Sensor control for an Oscillating Water Column plant
The Oscillating Water Column concept consists of two key elements, a turbine located in a pneumatic energy collection chamber and a doubly fed induction generator that converts energy extracted by the turbine into a form that can be returned to the network. Since the turbo-generator control requires the rotor angular velocity, removing the rotor speed sensor simplifies the hardware, with the consequent reduction in installation and maintenance costs which is even more relevant in the rough working sea conditions. In this particular case, a Luenberger based observer is considered and the effectiveness of the proposed control is shown by numerical simulations. Comparing these results with those obtained using a traditional speed sensor, it is shown that the proposed solution provides better performance since it allows a more reliable and robust performance of the plant.
- Open Access
- 1 January 2013
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2013, 1-14
Performance of an Ocean Energy Conversion System with DFIG Sensorless Control
The 2009/28/EC Directive requires Member States of the European Union to adopt a National Action Plan for Renewable Energy. In this context, the Basque Energy Board, EVE, is committed to research activities such as the Mutriku Oscillating Water Column plant, OWC. This is an experimental facility whose concept consists of a turbine located in a pneumatic energy collection chamber and a doubly fed induction generator that converts energy extracted by the turbine into a form that can be returned to the network. The turbo-generator control requires a precise knowledge of system parameters and of the rotor angular velocity in particular. Thus, to remove the rotor speed sensor implies a simplification of the hardware that is always convenient in rough working conditions. In this particular case, a Luenberger based observer is considered and the effectiveness of the proposed control is shown by numerical simulations. Comparing these results with those obtained using a traditional speed sensor, it is shown that the proposed solution provides better performance since it increases power extraction in the sense that it allows a more reliable and robust performance of the plant, which is even more relevant in a hostile environment as the ocean.
- 1 January 2013
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2013, 1-14
Open AccessPerformance of an Ocean Energy Conversion System with DFIG Sensorless Control
The 2009/28/EC Directive requires Member States of the European Union to adopt a National Action Plan for Renewable Energy. In this context, the Basque Energy Board, EVE, is committed to research activities such as the Mutriku Oscillating Water Column plant, OWC. This is an experimental facility whose concept consists of a turbine located in a pneumatic energy collection chamber and a doubly fed induction generator that converts energy extracted by the turbine into a form that can be returned to the network. The turbo-generator control requires a precise knowledge of system parameters and of the rotor angular velocity in particular. Thus, to remove the rotor speed sensor implies a simplification of the hardware that is always convenient in rough working conditions. In this particular case, a Luenberger based observer is considered and the effectiveness of the proposed control is shown by numerical simulations. Comparing these results with those obtained using a traditional speed sensor, it is shown that the proposed solution provides better performance since it increases power extraction in the sense that it allows a more reliable and robust performance of the plant, which is even more relevant in a hostile environment as the ocean.
- 1 December 2012
- Published by Elsevier in Renewable Energy
- Vol. 48, 16-26
Neural control for voltage dips ride-through of oscillating water column-based wave energy converter equipped with doubly-fed induction generator
- 1 December 2012
- Published by Elsevier in Renewable Energy
- Vol. 48, 16-26
Neural control for voltage dips ride-through of oscillating water column-based wave energy converter equipped with doubly-fed induction generator
- 1 November 2012
- Published by Elsevier in Electric Power Systems Research
- Vol. 92, 96-105
Neural control for wave power plant during voltage dips
- 1 November 2012
- Published by Elsevier in Electric Power Systems Research
- Vol. 92, 96-105
Neural control for wave power plant during voltage dips
- 1 November 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 48 (6) , 2372-2381
Sliding-Mode Control of Wave Power Generation Plants
The worldwide demand for energy requires alternatives to fossil fuels and nuclear fission, so renewable resources, particularly ocean energy, are called to play a relevant role in a near future. In particular, the oscillating water column (OWC) is one of the most promising devices to harness energy from the sea, as it is the case of the Nereida project plant, located in the Basque coast of Mutriku. This kind of devices consists of a particular type of turbine and a doubly fed induction generator. The turbogenerator module is usually controlled using a traditional proportional-integral (PI)-based vector control scheme, which requires an accurate knowledge of the system parameters and lacks of robustness, limiting, in some cases, the power extraction. To avoid these drawbacks, a novel sliding-mode-control-based vector control scheme for the OWC plant is presented in this paper. This variable-structure control is intrinsically robust under parameter uncertainties, which always appear in real systems, and presents a convenient disturbance rejection. The stability of the proposed controller is analyzed using the Lyapunov theory. The performance of the control scheme presented is proved by comparing it to the traditional PI-based vector control scheme in a series of representative maximum power generation case studies. Both numerical simulations and experimental results show that the proposed solution provides high-performance dynamic characteristics, improving the power extraction in spite of parameter uncertainties and system disturbances.
- 1 November 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 48 (6) , 2372-2381
Sliding-Mode Control of Wave Power Generation Plants
The worldwide demand for energy requires alternatives to fossil fuels and nuclear fission, so renewable resources, particularly ocean energy, are called to play a relevant role in a near future. In particular, the oscillating water column (OWC) is one of the most promising devices to harness energy from the sea, as it is the case of the Nereida project plant, located in the Basque coast of Mutriku. This kind of devices consists of a particular type of turbine and a doubly fed induction generator. The turbogenerator module is usually controlled using a traditional proportional-integral (PI)-based vector control scheme, which requires an accurate knowledge of the system parameters and lacks of robustness, limiting, in some cases, the power extraction. To avoid these drawbacks, a novel sliding-mode-control-based vector control scheme for the OWC plant is presented in this paper. This variable-structure control is intrinsically robust under parameter uncertainties, which always appear in real systems, and presents a convenient disturbance rejection. The stability of the proposed controller is analyzed using the Lyapunov theory. The performance of the control scheme presented is proved by comparing it to the traditional PI-based vector control scheme in a series of representative maximum power generation case studies. Both numerical simulations and experimental results show that the proposed solution provides high-performance dynamic characteristics, improving the power extraction in spite of parameter uncertainties and system disturbances.
- 1 July 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1485-1490
Control of Oscillating Water Column-based wave power generation plants for grid connection
There is a worldwide interest in the use of renewable resources for the generation of electrical power. Between all renewable energy sources, ocean energy is the one that still has the furthest to go to achieve commercial maturity. As the most promising ocean energy that can be harnessed in the Basque Country is wave energy, the NEREIDA MOWC project, promoted and led by Basque Energy Board, aims to prove the viability of this technology for future commercial plants. In this paper, an Oscillating Water Column-based wave power generation plant is modeled and controlled by means of a new control scheme that takes into account the influence of turbine damping and the main requirements imposed by new Grid Codes when a grid fault occurs on the transmission system.
- 1 July 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1485-1490
Control of Oscillating Water Column-based wave power generation plants for grid connection
There is a worldwide interest in the use of renewable resources for the generation of electrical power. Between all renewable energy sources, ocean energy is the one that still has the furthest to go to achieve commercial maturity. As the most promising ocean energy that can be harnessed in the Basque Country is wave energy, the NEREIDA MOWC project, promoted and led by Basque Energy Board, aims to prove the viability of this technology for future commercial plants. In this paper, an Oscillating Water Column-based wave power generation plant is modeled and controlled by means of a new control scheme that takes into account the influence of turbine damping and the main requirements imposed by new Grid Codes when a grid fault occurs on the transmission system.
- 1 December 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 26 (4) , 1021-1032
Complementary Control of Oscillating Water Column-Based Wave Energy Conversion Plants to Improve the Instantaneous Power Output
In this paper, an oscillating water column-based wave energy conversion plant is modeled and controlled by means of two complementary control strategies in order to improve the conversion of wave energy into electric power. This wave power generation system consists of a capture chamber, a Wells turbine, and an induction generator. The improvement relays on the implementation of a control scheme that combines two different control methods: a rotational speed control and an airflow control implemented by means of a throttle valve in series with the turbine. The use of rotational speed control provides a fast way to react to the abrupt and short changes in the turbine speed, ensuring that the average power of the generator is adequately adjusted according to the incident wave power level. Besides, a throttle-valve is used to control the flow through the turbine so as to increase the amount of energy produced, particularly at the higher incident wave power levels. These two control strategies complement each other, maximizing and improving the quality of supply by controlling and smoothing the generated power for different scenarios of wave oscillations, variations of wave grouping, and changes in the sea state.
- 1 December 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 26 (4) , 1021-1032
Complementary Control of Oscillating Water Column-Based Wave Energy Conversion Plants to Improve the Instantaneous Power Output
In this paper, an oscillating water column-based wave energy conversion plant is modeled and controlled by means of two complementary control strategies in order to improve the conversion of wave energy into electric power. This wave power generation system consists of a capture chamber, a Wells turbine, and an induction generator. The improvement relays on the implementation of a control scheme that combines two different control methods: a rotational speed control and an airflow control implemented by means of a throttle valve in series with the turbine. The use of rotational speed control provides a fast way to react to the abrupt and short changes in the turbine speed, ensuring that the average power of the generator is adequately adjusted according to the incident wave power level. Besides, a throttle-valve is used to control the flow through the turbine so as to increase the amount of energy produced, particularly at the higher incident wave power levels. These two control strategies complement each other, maximizing and improving the quality of supply by controlling and smoothing the generated power for different scenarios of wave oscillations, variations of wave grouping, and changes in the sea state.
- 1 June 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 371-377
Control for voltage dips Ride-Through of Oscillating Water Column-based wave power generation plant equipped with Doubly-Fed Induction Generator
One of the main problems arising when dealing with Oscillating Water Column-based wave power generation plants equipped with Doubly-Fed Induction Generator, is the need of an adequate Fault-Ride-Through during voltage drops. In this paper it is proposed an innovative Fault-Ride-Through solution consisting of a control scheme that suitably coordinates the air flow control, the active crowbar and the variable frequency converter, fulfilling the Grid Code. Besides, the variety of cases presented due to different sea states (amplitude and frequency) and characteristics of the grid fault (voltage drop and fault period), makes necessary to adequately modify the references used by the controllers in order to achieve the desired Fault-Ride-Through capability. That is, the application of the same controller references for different sea scenarios, provoke different responses of the plant for the same type of grid fault. In the same way, the application of the same controller references to the plant working under the same sea scenario when a grid fault of different voltage drops occurs on the transmission system, causes different reactions in the wave power plant. In this sense, it has been also implemented a control that adapts the controller references according to the pressure drop and voltage reduction, improving the controllability of the active and reactive power and the Fault-Ride Through capability during voltage drops.
- 1 June 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 371-377
Control for voltage dips Ride-Through of Oscillating Water Column-based wave power generation plant equipped with Doubly-Fed Induction Generator
One of the main problems arising when dealing with Oscillating Water Column-based wave power generation plants equipped with Doubly-Fed Induction Generator, is the need of an adequate Fault-Ride-Through during voltage drops. In this paper it is proposed an innovative Fault-Ride-Through solution consisting of a control scheme that suitably coordinates the air flow control, the active crowbar and the variable frequency converter, fulfilling the Grid Code. Besides, the variety of cases presented due to different sea states (amplitude and frequency) and characteristics of the grid fault (voltage drop and fault period), makes necessary to adequately modify the references used by the controllers in order to achieve the desired Fault-Ride-Through capability. That is, the application of the same controller references for different sea scenarios, provoke different responses of the plant for the same type of grid fault. In the same way, the application of the same controller references to the plant working under the same sea scenario when a grid fault of different voltage drops occurs on the transmission system, causes different reactions in the wave power plant. In this sense, it has been also implemented a control that adapts the controller references according to the pressure drop and voltage reduction, improving the controllability of the active and reactive power and the Fault-Ride Through capability during voltage drops.
- 23 February 2011
- Published by Taylor & Francis in International Journal of Control
- Vol. 84 (2) , 293-309
Neural rotational speed control for wave energy converters
Among the benefits arising from an increasing use of renewable energy are: enhanced security of energy supply, stimulation of economic growth, job creation and protection of the environment. In this context, this study analyses the performance of an oscillating water column device for wave energy conversion in function of the stalling behaviour in Wells turbines, one of the most widely used turbines in wave energy plants. For this purpose, a model of neural rotational speed control system is presented, simulated and implemented. This scheme is employed to appropriately adapt the speed of the doubly-fed induction generator coupled to the turbine according to the pressure drop entry, so as to avoid the undesired stalling behaviour. It is demonstrated that the proposed neural rotational speed control design adequately matches the desired relationship between the slip of the doubly-fed induction generator and the pressure drop input, improving the power generated by the turbine generator module.
- 23 February 2011
- Published by Taylor & Francis in International Journal of Control
- Vol. 84 (2) , 293-309
Neural rotational speed control for wave energy converters
Among the benefits arising from an increasing use of renewable energy are: enhanced security of energy supply, stimulation of economic growth, job creation and protection of the environment. In this context, this study analyses the performance of an oscillating water column device for wave energy conversion in function of the stalling behaviour in Wells turbines, one of the most widely used turbines in wave energy plants. For this purpose, a model of neural rotational speed control system is presented, simulated and implemented. This scheme is employed to appropriately adapt the speed of the doubly-fed induction generator coupled to the turbine according to the pressure drop entry, so as to avoid the undesired stalling behaviour. It is demonstrated that the proposed neural rotational speed control design adequately matches the desired relationship between the slip of the doubly-fed induction generator and the pressure drop input, improving the power generated by the turbine generator module.
- 1 December 2010
- Published by Elsevier in Renewable Energy
- Vol. 35 (12) , 2639-2648
Wave energy plants: Control strategies for avoiding the stalling behaviour in the Wells turbine
- 1 December 2010
- Published by Elsevier in Renewable Energy
- Vol. 35 (12) , 2639-2648
Wave energy plants: Control strategies for avoiding the stalling behaviour in the Wells turbine