Ezatollah Arzi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ezatollah Arzi has a total of 59 co-authors. Here are the top co-authors by number of shared publications:
- Yaser Abdi
University of Tehran
25 shared publications S. Mohajerzadeh
Department of Electrical and Computer Engineering, University of Tehran, Tehran, Iran
6 shared publicationsAlireza Hassani
5 shared publicationsHamid Esmaeilzadeh
5 shared publicationsFrançois Légaré
4 shared publications- Mehdi Ansari-Rad
Faculty of Physics, Shahrood University of Technology, Shahrood, Iran
4 shared publications
Latest Publications
- 1 August 2016
- Published by Elsevier in Solar Energy
- Vol. 133, 549-555
Local collection efficiency in the nano-crystalline solar cells
- 1 August 2016
- Published by Elsevier in Solar Energy
- Vol. 133, 549-555
Local collection efficiency in the nano-crystalline solar cells
- 15 March 2016
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 119 (11) , 114302
Enhancing the electron lifetime and diffusion coefficient in dye-sensitized solar cells by patterning the layer of TiO2 nanoparticles
In order to fulfill fast electron transport and low recombination rate in dye-sensitized solar cells, we propose to utilize a micro-patterned anode based on TiO2 nanoparticles. The micro-structures of the mesoporous TiO2 films were patterned by Si molds (microimprint technique). A series of measurements including the time of flight, open circuit voltage decay, and charge extraction is carried out to investigate the electron transport in these structures. Our measurement confirms the fast electron transport and high electron lifetime in the micro-patterned structures, which is in agreement with the previously reported simulations. The results have shown that for columnar 20 × 20 μm2 micro-structures, the electron diffusion coefficient is increased by 60% from 3.9 × 10−5 to 6.3 × 10−5 . In addition, the electron lifetime has considerably (about one order of magnitude) increased in the cells based on TiO2 micro-structures. These enhancements in the electron transport have significantly improved the power conversion efficiency of dye-sensitized solar cells, which is increased by 69% from 5.16% to 8.73%. The results are explained in terms of directional diffusion and extra trap states in the micro-structures of porous TiO2 films.- 15 March 2016
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 119 (11) , 114302
Enhancing the electron lifetime and diffusion coefficient in dye-sensitized solar cells by patterning the layer of TiO2 nanoparticles
In order to fulfill fast electron transport and low recombination rate in dye-sensitized solar cells, we propose to utilize a micro-patterned anode based on TiO2 nanoparticles. The micro-structures of the mesoporous TiO2 films were patterned by Si molds (microimprint technique). A series of measurements including the time of flight, open circuit voltage decay, and charge extraction is carried out to investigate the electron transport in these structures. Our measurement confirms the fast electron transport and high electron lifetime in the micro-patterned structures, which is in agreement with the previously reported simulations. The results have shown that for columnar 20 × 20 μm2 micro-structures, the electron diffusion coefficient is increased by 60% from 3.9 × 10−5 to 6.3 × 10−5 . In addition, the electron lifetime has considerably (about one order of magnitude) increased in the cells based on TiO2 micro-structures. These enhancements in the electron transport have significantly improved the power conversion efficiency of dye-sensitized solar cells, which is increased by 69% from 5.16% to 8.73%. The results are explained in terms of directional diffusion and extra trap states in the micro-structures of porous TiO2 films.- 1 June 2015
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 229, 8-14
A super continuum characterized high-precision SPR fiber optic sensor for refractometry
- 1 June 2015
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 229, 8-14
A super continuum characterized high-precision SPR fiber optic sensor for refractometry
- Open Access
- 29 May 2015
- Published by Optica Publishing Group in Optics Express
- Vol. 23 (11) , 14981-14992
Smart textile plasmonic fiber dew sensors
We propose a novel Surface Plasmon Resonance (SPR)-based sensor that detects dew formation in optical fiber-based smart textiles. The proposed SPR sensor facilitates the observation of two phenomena: condensation of moisture and evaporation of water molecules in air. This sensor detects dew formation in less than 0.25 s, and determines dew point temperature with an accuracy of 4%. It can be used to monitor water layer depth changes during dew formation and evaporation in the range of a plasmon depth probe, i.e., 250 nm, with a resolution of 7 nm. Further, it facilitates estimation of the relative humidity of a medium over a dynamic range of 30% to 70% by measuring the evaporation time via the plasmon depth probe.
- 29 May 2015
- Published by Optica Publishing Group in Optics Express
- Vol. 23 (11) , 14981-14992
Open AccessSmart textile plasmonic fiber dew sensors
We propose a novel Surface Plasmon Resonance (SPR)-based sensor that detects dew formation in optical fiber-based smart textiles. The proposed SPR sensor facilitates the observation of two phenomena: condensation of moisture and evaporation of water molecules in air. This sensor detects dew formation in less than 0.25 s, and determines dew point temperature with an accuracy of 4%. It can be used to monitor water layer depth changes during dew formation and evaporation in the range of a plasmon depth probe, i.e., 250 nm, with a resolution of 7 nm. Further, it facilitates estimation of the relative humidity of a medium over a dynamic range of 30% to 70% by measuring the evaporation time via the plasmon depth probe.
- 26 September 2014
- Published by Springer Nature in Journal of Nanoparticle Research
- Vol. 16 (10)
Gated graphene/titanium dioxide-based photodetector
- 26 September 2014
- Published by Springer Nature in Journal of Nanoparticle Research
- Vol. 16 (10)
Gated graphene/titanium dioxide-based photodetector
- 2 April 2014
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 140 (13) , 134702
Conditions for diffusion-limited and reaction-limited recombination in nanostructured solar cells
The performance of Dye-sensitized solar cells (DSC) and related devices made of nanostructured semiconductors relies on a good charge separation, which in turn is achieved by favoring charge transport against recombination. Although both processes occur at very different time scales, hence ensuring good charge separation, in certain cases the kinetics of transport and recombination can be connected, either in a direct or an indirect way. In this work, the connection between electron transport and recombination in nanostructured solar cells is studied both theoretically and by Monte Carlo simulation. Calculations using the Multiple-Trapping model and a realistic trap distribution for nanostructured TiO2 show that for attempt-to-jump frequencies higher than 1011–1013 Hz, the system adopts a reaction limited (RL) regime, with a lifetime which is effectively independent from the speed of the electrons in the transport level. For frequencies lower than those, and depending on the concentration of recombination centers in the material, the system enters a diffusion-limited regime (DL), where the lifetime increases if the speed of free electrons decreases. In general, the conditions for RL or DL recombination depend critically on the time scale difference between recombination kinetics and free-electron transport. Hence, if the former is too rapid with respect to the latter, the system is in the DL regime and total thermalization of carriers is not possible. In the opposite situation, a RL regime arises. Numerical data available in the literature, and the behavior of the lifetime with respect to (1) density of recombination centers and (2) probability of recombination at a given center, suggest that a typical DSC in operation stays in the RL regime with complete thermalization, although a transition to the DL regime may occur for electrolytes or hole conductors where recombination is especially rapid or where there is a larger dispersion of energies of electron acceptors.
- 2 April 2014
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 140 (13) , 134702
Conditions for diffusion-limited and reaction-limited recombination in nanostructured solar cells
The performance of Dye-sensitized solar cells (DSC) and related devices made of nanostructured semiconductors relies on a good charge separation, which in turn is achieved by favoring charge transport against recombination. Although both processes occur at very different time scales, hence ensuring good charge separation, in certain cases the kinetics of transport and recombination can be connected, either in a direct or an indirect way. In this work, the connection between electron transport and recombination in nanostructured solar cells is studied both theoretically and by Monte Carlo simulation. Calculations using the Multiple-Trapping model and a realistic trap distribution for nanostructured TiO2 show that for attempt-to-jump frequencies higher than 1011–1013 Hz, the system adopts a reaction limited (RL) regime, with a lifetime which is effectively independent from the speed of the electrons in the transport level. For frequencies lower than those, and depending on the concentration of recombination centers in the material, the system enters a diffusion-limited regime (DL), where the lifetime increases if the speed of free electrons decreases. In general, the conditions for RL or DL recombination depend critically on the time scale difference between recombination kinetics and free-electron transport. Hence, if the former is too rapid with respect to the latter, the system is in the DL regime and total thermalization of carriers is not possible. In the opposite situation, a RL regime arises. Numerical data available in the literature, and the behavior of the lifetime with respect to (1) density of recombination centers and (2) probability of recombination at a given center, suggest that a typical DSC in operation stays in the RL regime with complete thermalization, although a transition to the DL regime may occur for electrolytes or hole conductors where recombination is especially rapid or where there is a larger dispersion of energies of electron acceptors.
- 1 November 2013
- Published by Taylor & Francis in Journal of Modern Optics
- Vol. 60 (20) , 1813-1820
Controllable hybrid side-polishing method (CHPM) for optical fibers by combination of polishing and etching
We introduce the controllable hybrid polishing method (CHPM), which is a combination of enhanced side-polishing and etching methods, leading to a more controllable and precise clad polishing process for optical fibers. The two key advantages of CHPM are enabling of real-time monitoring of the etching process with a resolution of ~100 nm and fabrication of a 34% smoother polished surface than that of traditional polishing methods. Bearing in mind that these two factors are very important for the fabrication of any polished fiber devices, such as plasmonic sensors, the CHPM should prove highly useful in related industrial and scientific applications.
- 1 November 2013
- Published by Taylor & Francis in Journal of Modern Optics
- Vol. 60 (20) , 1813-1820
Controllable hybrid side-polishing method (CHPM) for optical fibers by combination of polishing and etching
We introduce the controllable hybrid polishing method (CHPM), which is a combination of enhanced side-polishing and etching methods, leading to a more controllable and precise clad polishing process for optical fibers. The two key advantages of CHPM are enabling of real-time monitoring of the etching process with a resolution of ~100 nm and fabrication of a 34% smoother polished surface than that of traditional polishing methods. Bearing in mind that these two factors are very important for the fabrication of any polished fiber devices, such as plasmonic sensors, the CHPM should prove highly useful in related industrial and scientific applications.
- 26 July 2013
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 46 (32) , 325103
Boundary integral method to calculate the sensitivity temperature error of microstructured fibre plasmonic sensors
In this paper, using the boundary integral method (BIM), we simulate the effect of temperature fluctuation on the sensitivity of microstructured optical fibre (MOF) surface plasmon resonance (SPR) sensors. The final results indicate that, as the temperature increases, the refractometry sensitivity of our sensor decreases from 1300 nm/RIU at 0 °C to 1200 nm/RIU at 50 °C, leading to ∼7.7% sensitivity reduction and the sensitivity temperature error of 0.15% °C−1 for this case. These results can be used for biosensing temperature-error adjustment in MOF SPR sensors, since biomaterials detection usually happens in this temperature range. Moreover, the signal-to-noise ratio (SNR) of our sensor decreases from 0.265 at 0 °C to 0.154 at 100 °C with the average reduction rate of ∼0.42% °C−1. The results suggest that at lower temperatures the sensor has a higher SNR.
- 26 July 2013
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 46 (32) , 325103
Boundary integral method to calculate the sensitivity temperature error of microstructured fibre plasmonic sensors
In this paper, using the boundary integral method (BIM), we simulate the effect of temperature fluctuation on the sensitivity of microstructured optical fibre (MOF) surface plasmon resonance (SPR) sensors. The final results indicate that, as the temperature increases, the refractometry sensitivity of our sensor decreases from 1300 nm/RIU at 0 °C to 1200 nm/RIU at 50 °C, leading to ∼7.7% sensitivity reduction and the sensitivity temperature error of 0.15% °C−1 for this case. These results can be used for biosensing temperature-error adjustment in MOF SPR sensors, since biomaterials detection usually happens in this temperature range. Moreover, the signal-to-noise ratio (SNR) of our sensor decreases from 0.265 at 0 °C to 0.154 at 100 °C with the average reduction rate of ∼0.42% °C−1. The results suggest that at lower temperatures the sensor has a higher SNR.