Guanqing Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Guanqing Sun has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Ren Liu
Key Laboratory of Synthetic and Biological Colloids, Ministry of Education, School of Chemical and Material Engineering, Jiangnan University, Wuxi, China
13 shared publications - Jing Luo
The Key Laboratory of Synthetic and Biological Colloids, Ministry of Education, School of Chemical and Material Engineering, Jiangnan University, Lihu Street 1800, Wuxi 214122, China
11 shared publications Jing Luo
6 shared publicationsRen Liu
6 shared publicationsTianheng Wang
Key Laboratory of Synthetic and Biological Colloids, Ministry of Education, School of Chemical and Material Engineering, Jiangnan University, Wuxi, 214122 Jiangsu, China
5 shared publications- To Ngai
The Chinese University of Hong Kong
5 shared publications
Latest Publications
- 11 September 2025
- Published by American Chemical Society (ACS) in Langmuir
Efficient Preparation of Janus Particles with Controllable Morphology and Composition via Photopolymerization
Janus particles (JPs) with anisotropic shape and composition are of great significance in the fabrication of functional materials, but the efficient preparation of JPs and easy modulation of the JPs' lobe composition and morphology are still challenges. In this work, a method combining 'phase separation inside emulsion droplet' and photopolymerization was proposed for the one-pot preparation of JPs. In our strategy, two kinds of ultraviolet (UV)-curable prepolymers with different surface tensions were dissolved in a cosolvent and dispersed in an aqueous emulsifier solution. With the volatilization of the solvent, two prepolymers separated from each other, migrated to the two sides of the emulsion droplet, and converted to Janus particles via UV-initiated polymerization. The strategy possessed the advantages of convenience, high efficiency, mild conditions (room temperature), and high yield (>80%), which provided a reliable approach for the large-scale preparation of JPs. On the basis of the theory of spreading coefficient, we explored the effect of UV-curable prepolymers and emulsifiers on the morphologies of JPs (such as snowman and dumbbell), and the relationship between the morphologies and the interfacial tension between the prepolymers and the aqueous phase was systematically analyzed. In addition, the lobe ratio and the particle size of the JPs could be easily regulated by adjusting the feeding ratio and emulsification speed, which further broadened the regulation range of the JPs.
- 11 September 2025
- Published by American Chemical Society (ACS) in Langmuir
Efficient Preparation of Janus Particles with Controllable Morphology and Composition via Photopolymerization
Janus particles (JPs) with anisotropic shape and composition are of great significance in the fabrication of functional materials, but the efficient preparation of JPs and easy modulation of the JPs' lobe composition and morphology are still challenges. In this work, a method combining 'phase separation inside emulsion droplet' and photopolymerization was proposed for the one-pot preparation of JPs. In our strategy, two kinds of ultraviolet (UV)-curable prepolymers with different surface tensions were dissolved in a cosolvent and dispersed in an aqueous emulsifier solution. With the volatilization of the solvent, two prepolymers separated from each other, migrated to the two sides of the emulsion droplet, and converted to Janus particles via UV-initiated polymerization. The strategy possessed the advantages of convenience, high efficiency, mild conditions (room temperature), and high yield (>80%), which provided a reliable approach for the large-scale preparation of JPs. On the basis of the theory of spreading coefficient, we explored the effect of UV-curable prepolymers and emulsifiers on the morphologies of JPs (such as snowman and dumbbell), and the relationship between the morphologies and the interfacial tension between the prepolymers and the aqueous phase was systematically analyzed. In addition, the lobe ratio and the particle size of the JPs could be easily regulated by adjusting the feeding ratio and emulsification speed, which further broadened the regulation range of the JPs.
Programmable Control of Active Ingredient Release in Pickering Emulsions Using Light
Pickering emulsions have garnered significant attention for their ability to facilitate the controlled and effective delivery of active ingredients across various sectors, including drug release, agriculture, cosmetics, and interfacial catalysis. However, achieving the release of encapsulated active substances typically requires the disruption of emulsion droplets, making programmable release a notable challenge. This study develops a colloidal layer with nanogates at the oil‐water interface of Pickering emulsion, utilizing UV light as a non‐contact, remote stimulus to enable effective programmable release of encapsulated active substances. By alternating UV and visible light irradiation, this work induces cis‐trans isomerization of azobenzene molecules on silica particles, allowing the gaps between colloidal particles to open and close. This demonstrated a promising nanogate effect under UV irradiation, facilitating the programmable release of active substance (perylene) from the Pickering emulsion droplets. This Pickering emulsion system offers precise control over the release amount of perylene by adjusting the colloidal particle size and the duration of UV–visible light exposure, all while maintaining emulsion stability. The successful implementation of this strategy presents a promising platform for non‐invasive, programmable release of active substances across diverse applications in food, cosmetics and pharmaceutical fields.
Programmable Control of Active Ingredient Release in Pickering Emulsions Using Light
Pickering emulsions have garnered significant attention for their ability to facilitate the controlled and effective delivery of active ingredients across various sectors, including drug release, agriculture, cosmetics, and interfacial catalysis. However, achieving the release of encapsulated active substances typically requires the disruption of emulsion droplets, making programmable release a notable challenge. This study develops a colloidal layer with nanogates at the oil‐water interface of Pickering emulsion, utilizing UV light as a non‐contact, remote stimulus to enable effective programmable release of encapsulated active substances. By alternating UV and visible light irradiation, this work induces cis‐trans isomerization of azobenzene molecules on silica particles, allowing the gaps between colloidal particles to open and close. This demonstrated a promising nanogate effect under UV irradiation, facilitating the programmable release of active substance (perylene) from the Pickering emulsion droplets. This Pickering emulsion system offers precise control over the release amount of perylene by adjusting the colloidal particle size and the duration of UV–visible light exposure, all while maintaining emulsion stability. The successful implementation of this strategy presents a promising platform for non‐invasive, programmable release of active substances across diverse applications in food, cosmetics and pharmaceutical fields.
- 11 February 2025
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 41 (7) , 4672-4683
Efficient Preparation of Core–Shell Particles via Photopolymerization for Toughening Photocurable Resins
Core-shell particles have been widely used in improving the toughness of resin, but a convenient and efficient large-scale preparation method for core-shell particles is lacking currently. In this work, an efficient and simple method has been developed to fabricate core-shell particles by combining photopolymerization and phase separation inside the emulsion droplet. In this strategy, two photocurable prepolymers with different hydrophilicity were dissolved in a cosolvent and dispersed in an aqueous solution to form an emulsion. Upon the removal of the cosolvent, phase separation occurred inside the emulsion droplet. The hydrophilic prepolymer migrated toward the oil-water interface and converted to a shell under UV irradiation, while the hydrophobic prepolymer migrated to the interior of the emulsion droplet and converted to a core. In addition, the core-shell ratio and size of the particle could be easily adjusted, which provided an idea for the efficient and large-scale preparation of the core-shell particle. The influence of the structure and contents of the core-shell particles on the toughening effect was investigated. Under the optimal parameters (the core-shell ratio of 1:1, the size of 1 μm, and the concentration of 7.5 wt %), the toughness, impact strength, flexural strength, and fracture toughness (KIC) of the composites were enhanced by 52, 8.4, 30.8, and 288.4% compared to the pure resin system, respectively. Furthermore, the Tg value and the viscosity of the resin system were not greatly influenced after the addition of core-shell particles, i.e., an outstanding toughening effect was achieved without sacrificing its thermal property and processability.
- 11 February 2025
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 41 (7) , 4672-4683
Efficient Preparation of Core–Shell Particles via Photopolymerization for Toughening Photocurable Resins
Core-shell particles have been widely used in improving the toughness of resin, but a convenient and efficient large-scale preparation method for core-shell particles is lacking currently. In this work, an efficient and simple method has been developed to fabricate core-shell particles by combining photopolymerization and phase separation inside the emulsion droplet. In this strategy, two photocurable prepolymers with different hydrophilicity were dissolved in a cosolvent and dispersed in an aqueous solution to form an emulsion. Upon the removal of the cosolvent, phase separation occurred inside the emulsion droplet. The hydrophilic prepolymer migrated toward the oil-water interface and converted to a shell under UV irradiation, while the hydrophobic prepolymer migrated to the interior of the emulsion droplet and converted to a core. In addition, the core-shell ratio and size of the particle could be easily adjusted, which provided an idea for the efficient and large-scale preparation of the core-shell particle. The influence of the structure and contents of the core-shell particles on the toughening effect was investigated. Under the optimal parameters (the core-shell ratio of 1:1, the size of 1 μm, and the concentration of 7.5 wt %), the toughness, impact strength, flexural strength, and fracture toughness (KIC) of the composites were enhanced by 52, 8.4, 30.8, and 288.4% compared to the pure resin system, respectively. Furthermore, the Tg value and the viscosity of the resin system were not greatly influenced after the addition of core-shell particles, i.e., an outstanding toughening effect was achieved without sacrificing its thermal property and processability.
- 12 October 2024
- Published by Elsevier in Journal of Colloid and Interface Science
- Vol. 679 (Pt A) , 1150-1158
Photo-responsive Pickering emulsions triggered by in-situ pH modulation using a photoacid generator
- 12 October 2024
- Published by Elsevier in Journal of Colloid and Interface Science
- Vol. 679 (Pt A) , 1150-1158
Photo-responsive Pickering emulsions triggered by in-situ pH modulation using a photoacid generator
- Open Access
- 19 August 2024
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 40 (35) , 18652-18660
Unraveling the Complexities of Silica Nanoparticle Adsorption onto Polymer Latexes in Pickering Emulsion Polymerization
Incorporating unmodified silica nanoparticles onto polymer latexes to fabricate aqueous polymer dispersions without relying on electrostatic attraction during the Pickering emulsion polymerization process still faces challenges. For negatively charged silica nanoparticles to successfully adsorb onto polymer latexes, particularly in an anionic initiator emulsion polymerization system, they have remained elusive without the use of auxiliary monomers and cationic initiators. This study investigates various experimental parameters, such as emulsion polymerization temperature, monomer solubility, salt concentration, and cation type, to elucidate the factors influencing the adsorption of unmodified silica nanoparticles in Pickering emulsion polymerization. While poly(methyl methacrylate) (PMMA)/SiO2 hybrid latexes can be obtained under pH conditions of 5-6 and at temperatures of 65 °C or below, the loading rate of silica nanoparticles decreases as the reaction temperature increases, resulting in bare PMMA latexes without silica nanoparticle adsorption at temperatures exceeding 70 °C. Introducing styrene (St) into the monomer mixture with methyl methacrylate in a ratio of up to 10 wt % leads to a gradual decrease in silica nanoparticle loading rate, from 27.3 to 8.2 wt %, attributed to the low solubility of St in water. Furthermore, the presence of sodium ions (Na+) is found to be crucial for silica nanoparticle adsorption onto PMMA latexes, as the sodium ions have a stabilizing effect on both the silica nanoparticles and the silica nanoparticle-armored latexes. These findings highlight the complex nature of Pickering emulsion polymerization in the presence of unmodified silica nanoparticles, demonstrating that the loading rate of silica nanoparticles onto polymer latexes is influenced by various factors. These insights pave the way for developing aqueous polymer dispersions with high silica nanoparticle loading rates onto polymer latexes, which is a desirable trait in the coating industry.
- 19 August 2024
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 40 (35) , 18652-18660
Open AccessUnraveling the Complexities of Silica Nanoparticle Adsorption onto Polymer Latexes in Pickering Emulsion Polymerization
Incorporating unmodified silica nanoparticles onto polymer latexes to fabricate aqueous polymer dispersions without relying on electrostatic attraction during the Pickering emulsion polymerization process still faces challenges. For negatively charged silica nanoparticles to successfully adsorb onto polymer latexes, particularly in an anionic initiator emulsion polymerization system, they have remained elusive without the use of auxiliary monomers and cationic initiators. This study investigates various experimental parameters, such as emulsion polymerization temperature, monomer solubility, salt concentration, and cation type, to elucidate the factors influencing the adsorption of unmodified silica nanoparticles in Pickering emulsion polymerization. While poly(methyl methacrylate) (PMMA)/SiO2 hybrid latexes can be obtained under pH conditions of 5-6 and at temperatures of 65 °C or below, the loading rate of silica nanoparticles decreases as the reaction temperature increases, resulting in bare PMMA latexes without silica nanoparticle adsorption at temperatures exceeding 70 °C. Introducing styrene (St) into the monomer mixture with methyl methacrylate in a ratio of up to 10 wt % leads to a gradual decrease in silica nanoparticle loading rate, from 27.3 to 8.2 wt %, attributed to the low solubility of St in water. Furthermore, the presence of sodium ions (Na+) is found to be crucial for silica nanoparticle adsorption onto PMMA latexes, as the sodium ions have a stabilizing effect on both the silica nanoparticles and the silica nanoparticle-armored latexes. These findings highlight the complex nature of Pickering emulsion polymerization in the presence of unmodified silica nanoparticles, demonstrating that the loading rate of silica nanoparticles onto polymer latexes is influenced by various factors. These insights pave the way for developing aqueous polymer dispersions with high silica nanoparticle loading rates onto polymer latexes, which is a desirable trait in the coating industry.
- 29 July 2024
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 6 (15) , 8811-8820
Encapsulation of Dyed Alkanes with Polyurethane Microcapsules from Interfacial Polymerization Enables Irreversible Thermochromic Coatings
- 29 July 2024
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 6 (15) , 8811-8820
Encapsulation of Dyed Alkanes with Polyurethane Microcapsules from Interfacial Polymerization Enables Irreversible Thermochromic Coatings