Zaoyang Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Zaoyang Li has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
- Lijun Liu
State Key Laboratory of Lithospheric Evolution, Institute of Geology and Geophysics, Chinese Academy of Sciences, Beijing 100029, China
21 shared publications Lijun Liu
Xi’an Jiaotong University
6 shared publicationsJiancheng Li
School of Energy and Power Engineering, Xi'an Jiaotong University, Xi'an, Shaanxi 710049, China
4 shared publications- Jinping Luo
School of Energy and Power Engineering, Xi’an Jiaotong University 1 , Xi’an, Shaanxi 710049
4 shared publications - Chao Qi
School of Energy and Power Engineering, Xi’an Jiaotong University , Xi’an, Shaanxi 710049
3 shared publications Dengnian Li
School of Energy and Power Engineering, Xi’an Jiaotong University , Xi’an, Shaanxi 710049
3 shared publications
Latest Publications
- 12 November 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (45) , 455104
Sn dopant transport and uniformity in β -Ga 2 O 3 crystal growth by the edge-defined film-fed growth method
Dopant segregation during crystal growth can lead to non-uniform dopant distributions, compromising material uniformity and device reliability. Experimental studies have shown that the crystallization interface shape significantly affects dopant distribution in β -Ga 2 O 3 crystals grown by the edge-defined film-fed growth (EFG) method; however, the underlying mechanisms remain unclear. To address this issue, a global three-dimensional numerical model of β -Ga 2 O 3 crystal growth by the EFG method is developed by coupling dynamic crystallization interface tracking with dopant transport. The simulations reveal that both convective and diffusive transport play important and comparable roles in determining the dopant distribution within the liquid bridge. The crystallization interface shape affects dopant segregation at the crystallization front by modifying both the convective flow and the diffusion pathways of the dopant. In particular, increasing the liquid-bridge thickness reduces the resistance to lateral dopant diffusion, thereby enhancing lateral dopant redistribution and improving dopant uniformity. Based on this mechanistic understanding, a die structure with a top groove is found to provide an additional advantage in dopant uniformity while maintaining a convex crystallization interface favorable for growth stability. These results demonstrate that diffusion transport, together with convection, is an important mechanism governing dopant redistribution during β -Ga 2 O 3 crystal growth by the EFG method, provide fundamental insight into the coupling between crystallization interface shape and mass transport, and offer practical guidance for improving dopant uniformity.
- 12 November 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (45) , 455104
Sn dopant transport and uniformity in β -Ga 2 O 3 crystal growth by the edge-defined film-fed growth method
Dopant segregation during crystal growth can lead to non-uniform dopant distributions, compromising material uniformity and device reliability. Experimental studies have shown that the crystallization interface shape significantly affects dopant distribution in β -Ga 2 O 3 crystals grown by the edge-defined film-fed growth (EFG) method; however, the underlying mechanisms remain unclear. To address this issue, a global three-dimensional numerical model of β -Ga 2 O 3 crystal growth by the EFG method is developed by coupling dynamic crystallization interface tracking with dopant transport. The simulations reveal that both convective and diffusive transport play important and comparable roles in determining the dopant distribution within the liquid bridge. The crystallization interface shape affects dopant segregation at the crystallization front by modifying both the convective flow and the diffusion pathways of the dopant. In particular, increasing the liquid-bridge thickness reduces the resistance to lateral dopant diffusion, thereby enhancing lateral dopant redistribution and improving dopant uniformity. Based on this mechanistic understanding, a die structure with a top groove is found to provide an additional advantage in dopant uniformity while maintaining a convex crystallization interface favorable for growth stability. These results demonstrate that diffusion transport, together with convection, is an important mechanism governing dopant redistribution during β -Ga 2 O 3 crystal growth by the EFG method, provide fundamental insight into the coupling between crystallization interface shape and mass transport, and offer practical guidance for improving dopant uniformity.
- Open Access
- 27 June 2026
- Published by Elsevier in SSRN Electronic Journal
Numerical study on thermal management of Lithium-ion batteries utilizing liquid-cooled plate with branch channels coupled with grooves and fins
As high-rate power batteries for new energy vehicles rapidly advance, liquid cooling has emerged as the favored technique for controlling battery temperature.Traditional single-structure liquid-cooled plates often experience uneven flow distribution and areas with poor heat transfer. This study introduces a composite enhanced liquid-cooled plate for Lithium-ion batteries that combines branch channels, circular grooves, and circular fins. The optimized branch channels improve flow uniformity, resulting in a 22.59% boost in overall performance. Among three groove types tested in a single channel model, circular grooves provide the best flow disturbance and heat transfer, achieving maximum increases of 99.10% in the average Nusselt number and 76.67% in the performance evaluation criterion. Adding fins inside the grooves, particularly circular fins, significantly reduces low-velocity stagnant zones and delivers the highest heat transfer enhancement. The findings demonstrate that this composite design effectively improves flow distribution. At an inlet velocity of 0.60 m/s and a 3C discharge rate, the maximum battery temperature and temperature difference decrease by 2.91 K and 2.38 K respectively compared to the baseline model, while the overall performance index PEC increases by 71.01%, achieving a balanced improvement in efficient heat dissipation and temperature uniformity. This approach provides valuable insights for designing liquid-cooled plates for high-rate power batteries.
- 27 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessNumerical study on thermal management of Lithium-ion batteries utilizing liquid-cooled plate with branch channels coupled with grooves and fins
As high-rate power batteries for new energy vehicles rapidly advance, liquid cooling has emerged as the favored technique for controlling battery temperature.Traditional single-structure liquid-cooled plates often experience uneven flow distribution and areas with poor heat transfer. This study introduces a composite enhanced liquid-cooled plate for Lithium-ion batteries that combines branch channels, circular grooves, and circular fins. The optimized branch channels improve flow uniformity, resulting in a 22.59% boost in overall performance. Among three groove types tested in a single channel model, circular grooves provide the best flow disturbance and heat transfer, achieving maximum increases of 99.10% in the average Nusselt number and 76.67% in the performance evaluation criterion. Adding fins inside the grooves, particularly circular fins, significantly reduces low-velocity stagnant zones and delivers the highest heat transfer enhancement. The findings demonstrate that this composite design effectively improves flow distribution. At an inlet velocity of 0.60 m/s and a 3C discharge rate, the maximum battery temperature and temperature difference decrease by 2.91 K and 2.38 K respectively compared to the baseline model, while the overall performance index PEC increases by 71.01%, achieving a balanced improvement in efficient heat dissipation and temperature uniformity. This approach provides valuable insights for designing liquid-cooled plates for high-rate power batteries.
- Open Access
- 22 April 2026
- Published by Elsevier in SSRN Electronic Journal
Numerical investigation on the cooling performance of liquid-cooled plates based on Hilbert Curve structure for lithium-ion batteries
This study introduces a novel liquid-cooled plate design employing Hilbert curve geometry to address the typical compromises among temperature uniformity, flow resistance, and spatial limitations commonly encountered in traditional configurations. The effects of coolant flow direction, inlet velocity magnitude, and the channel size on heat dissipation efficiency were systematically examined based on three-dimensional numerical simulations and an orthogonal experimental design. The findings indicate that the novel design promotes heat transfer between the cooling medium and channel walls via sequential 90° bends and periodic variations in channel cross-section. Additionally, the extended flow channel facilitates enhanced thermal dissipation without necessitating an expansion of physical plate dimensions. Under operating conditions of 1.5C discharge rate and 1.0 m·s⁻¹ inlet velocity, the Hilbert-curve Micro-Channel Plate exhibited a maximum temperature reduction of 0.31 K and a 24% decrease in temperature difference relative to the 8-channel parallel plate configuration, corresponding reductions for the 32-channel plate were 0.39 K and 34%, respectively. The performance evaluation criterion PEC consistently exceeded 1.76 across all discharge rates, attaining a peak value of 4.31 at 2.5C. Optimal operational conditions were identified as a 7 mm channel width, 1.0 m·s⁻¹ flow velocity, 298.0 K coolant temperature, and a 1.5C discharge rate.
- 22 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessNumerical investigation on the cooling performance of liquid-cooled plates based on Hilbert Curve structure for lithium-ion batteries
This study introduces a novel liquid-cooled plate design employing Hilbert curve geometry to address the typical compromises among temperature uniformity, flow resistance, and spatial limitations commonly encountered in traditional configurations. The effects of coolant flow direction, inlet velocity magnitude, and the channel size on heat dissipation efficiency were systematically examined based on three-dimensional numerical simulations and an orthogonal experimental design. The findings indicate that the novel design promotes heat transfer between the cooling medium and channel walls via sequential 90° bends and periodic variations in channel cross-section. Additionally, the extended flow channel facilitates enhanced thermal dissipation without necessitating an expansion of physical plate dimensions. Under operating conditions of 1.5C discharge rate and 1.0 m·s⁻¹ inlet velocity, the Hilbert-curve Micro-Channel Plate exhibited a maximum temperature reduction of 0.31 K and a 24% decrease in temperature difference relative to the 8-channel parallel plate configuration, corresponding reductions for the 32-channel plate were 0.39 K and 34%, respectively. The performance evaluation criterion PEC consistently exceeded 1.76 across all discharge rates, attaining a peak value of 4.31 at 2.5C. Optimal operational conditions were identified as a 7 mm channel width, 1.0 m·s⁻¹ flow velocity, 298.0 K coolant temperature, and a 1.5C discharge rate.
- 11 September 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (6)
Comparison of heat transfer and heat loss between 3D thermal-electric coupling model and 2D model in Czochralski silicon growth
Czochralski (CZ) silicon is widely utilized as a crucial substrate material in the semiconductor industry. As an effective and cost-efficient approach, numerical simulation has been widely used to study heat transfer and heat loss for improving crystal quality and reducing heat losses. Regarding numerical models, the traditional 2D model simplifies the CZ furnace axisymmetrically and the previous 3D models often neglect the full coupling between the thermal and electric fields in the heating system. In this work, a 3D global thermal-electric full coupling model for CZ silicon growth is established. Based on the novel 3D model, the 3D distribution characteristics of heat transfer and Joule heat in the CZ furnace are investigated. Further, by comparisons between novel 3D and traditional 2D models, the limitations of the traditional 2D model on simulating the distribution of thermal fields, heating system Joule heat, furnace heat losses, and furnace heat flow network are systematically investigated. The results indicate that the heater Joule heat exhibits a nonuniform distribution and the furnace temperature displays a nonaxisymmetric profile in the novel 3D model, which cannot be captured by the traditional 2D model. Additionally, the traditional 2D model underestimates the total heat loss and overestimates both temperature and its gradient within the silicon melt. This study evaluates the limitations of the traditional 2D model of CZ silicon growth in simulating heat transfer and heat loss, thereby facilitating more effective application of numerical simulation to promote high-quality and low-cost crystal growth.
- 11 September 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (6)
Comparison of heat transfer and heat loss between 3D thermal-electric coupling model and 2D model in Czochralski silicon growth
Czochralski (CZ) silicon is widely utilized as a crucial substrate material in the semiconductor industry. As an effective and cost-efficient approach, numerical simulation has been widely used to study heat transfer and heat loss for improving crystal quality and reducing heat losses. Regarding numerical models, the traditional 2D model simplifies the CZ furnace axisymmetrically and the previous 3D models often neglect the full coupling between the thermal and electric fields in the heating system. In this work, a 3D global thermal-electric full coupling model for CZ silicon growth is established. Based on the novel 3D model, the 3D distribution characteristics of heat transfer and Joule heat in the CZ furnace are investigated. Further, by comparisons between novel 3D and traditional 2D models, the limitations of the traditional 2D model on simulating the distribution of thermal fields, heating system Joule heat, furnace heat losses, and furnace heat flow network are systematically investigated. The results indicate that the heater Joule heat exhibits a nonuniform distribution and the furnace temperature displays a nonaxisymmetric profile in the novel 3D model, which cannot be captured by the traditional 2D model. Additionally, the traditional 2D model underestimates the total heat loss and overestimates both temperature and its gradient within the silicon melt. This study evaluates the limitations of the traditional 2D model of CZ silicon growth in simulating heat transfer and heat loss, thereby facilitating more effective application of numerical simulation to promote high-quality and low-cost crystal growth.
- 19 August 2025
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 27 (34) , 5769-5778
A quantitative method for investigating 3D oxygen transport pathways in Czochralski growth of a silicon crystal
The origin, destination and the exact shape of the oxygen transport pathways in the Cz method are quantitatively computed.
- 19 August 2025
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 27 (34) , 5769-5778
A quantitative method for investigating 3D oxygen transport pathways in Czochralski growth of a silicon crystal
The origin, destination and the exact shape of the oxygen transport pathways in the Cz method are quantitatively computed.
- 1 January 2025
- Published by Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences in Acta Physica Sinica
- Vol. 74 (15) , 158101
Effects of crystal rotation on SiC crystal growth by top-seeded solution growth method
The top-seeded solution growth (TSSG) method is a critical technique for growing low-defect and high-quality silicon carbide (SiC) single crystals. A comprehensive numerical analysis model including induction heating, heat and mass transfer is developed for growing 6-inch SiC single crystals. The coupling effects of Lorentz force, centrifugal force, thermal buoyancy force and surface tension on the solution flow are considered, and the effects of crystal rotation speed on the velocity field, temperature field, carbon concentration field, crystal growth rate and carbon dissolution and precipitation on the crucible wall are systematically investigated. The results indicate that the Lorentz force in the solution results in a more complex flow field at low crystal rotation speeds. The crystal rotation speed should be controlled within the appropriate range to ensure that the carbon concentration distribution beneath the growth interface determined by the transport mode is coordinated with that at the growth interface determined by the temperature, which is beneficial for the uniform and high growth rate of SiC single crystals. Low rotation speeds reduce the growth rate of SiC single crystals, while high rotation speeds lead radial uniformity of growth rate to decrease. At a rotation speed of 25 r/min, the average growth rate of SiC single crystals is higher and the radial distribution uniformity is better. Further analysis is conducted on the dissolution and precipitation of carbon at the solution-crucible interface, and the regions, where the crucible wall dissolves quickly and SiC polycrystalline particles are generated, are located. The transport directions of polycrystalline particles are predicted based on the velocity field. The research results provide a scientific basis for growing 6-inch SiC single crystals by TSSG method.
- 1 January 2025
- Published by Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences in Acta Physica Sinica
- Vol. 74 (15) , 158101
Effects of crystal rotation on SiC crystal growth by top-seeded solution growth method
The top-seeded solution growth (TSSG) method is a critical technique for growing low-defect and high-quality silicon carbide (SiC) single crystals. A comprehensive numerical analysis model including induction heating, heat and mass transfer is developed for growing 6-inch SiC single crystals. The coupling effects of Lorentz force, centrifugal force, thermal buoyancy force and surface tension on the solution flow are considered, and the effects of crystal rotation speed on the velocity field, temperature field, carbon concentration field, crystal growth rate and carbon dissolution and precipitation on the crucible wall are systematically investigated. The results indicate that the Lorentz force in the solution results in a more complex flow field at low crystal rotation speeds. The crystal rotation speed should be controlled within the appropriate range to ensure that the carbon concentration distribution beneath the growth interface determined by the transport mode is coordinated with that at the growth interface determined by the temperature, which is beneficial for the uniform and high growth rate of SiC single crystals. Low rotation speeds reduce the growth rate of SiC single crystals, while high rotation speeds lead radial uniformity of growth rate to decrease. At a rotation speed of 25 r/min, the average growth rate of SiC single crystals is higher and the radial distribution uniformity is better. Further analysis is conducted on the dissolution and precipitation of carbon at the solution-crucible interface, and the regions, where the crucible wall dissolves quickly and SiC polycrystalline particles are generated, are located. The transport directions of polycrystalline particles are predicted based on the velocity field. The research results provide a scientific basis for growing 6-inch SiC single crystals by TSSG method.
- 1 January 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (1)
3D numerical modeling and simulation of β-Ga2O3 crystal growth by edge-defined film-fed growth method
Numerical simulation is an effective approach for improving the edge-defined film-fed growth (EFG) of β-Ga2O3 crystals by studying the heat transfer, melt flow, and crystallization interface shape. However, the nonaxisymmetric structure of the EFG furnace, the anisotropy of the β-Ga2O3 crystal, the infrared radiation absorption by free carriers, and the tracking of three-dimensional (3D) crystallization interface shape bring challenges in modeling and simulation. In this study, a global 3D nonaxisymmetric numerical model was established for the growth of ribbon β-Ga2O3 crystals. The anisotropic thermal conduction coupled with the thermal radiation inside the crystal was considered, and the dynamic mesh technique was developed to track the severely deformed crystallization interface. Subsequently, the numerical model was used to study the influences of thermal radiation absorption by free carriers on temperature distribution and crystallization interface shape. The results indicate that the thermal radiation absorption inside the crystal directly affects the shape of the crystallization interface and the stability of crystal growth. Strong radiation absorption leads to a concave crystallization interface, whereas the concavity of the interface shape exhibits a decreasing trend with the increase of crystal height, which is beyond expectation. All these phenomena are related to the heat transfer and temperature distribution in the EFG furnace, and the 3D numerical modeling and simulation are helpful in deeply understanding the reasons behind the phenomena and improving the β-Ga2O3 crystal growth.
- 1 January 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (1)
3D numerical modeling and simulation of β-Ga2O3 crystal growth by edge-defined film-fed growth method
Numerical simulation is an effective approach for improving the edge-defined film-fed growth (EFG) of β-Ga2O3 crystals by studying the heat transfer, melt flow, and crystallization interface shape. However, the nonaxisymmetric structure of the EFG furnace, the anisotropy of the β-Ga2O3 crystal, the infrared radiation absorption by free carriers, and the tracking of three-dimensional (3D) crystallization interface shape bring challenges in modeling and simulation. In this study, a global 3D nonaxisymmetric numerical model was established for the growth of ribbon β-Ga2O3 crystals. The anisotropic thermal conduction coupled with the thermal radiation inside the crystal was considered, and the dynamic mesh technique was developed to track the severely deformed crystallization interface. Subsequently, the numerical model was used to study the influences of thermal radiation absorption by free carriers on temperature distribution and crystallization interface shape. The results indicate that the thermal radiation absorption inside the crystal directly affects the shape of the crystallization interface and the stability of crystal growth. Strong radiation absorption leads to a concave crystallization interface, whereas the concavity of the interface shape exhibits a decreasing trend with the increase of crystal height, which is beyond expectation. All these phenomena are related to the heat transfer and temperature distribution in the EFG furnace, and the 3D numerical modeling and simulation are helpful in deeply understanding the reasons behind the phenomena and improving the β-Ga2O3 crystal growth.
- 11 September 2024
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 26 (39) , 5531-5540
Study on power consumption and heat transfer paths in Czochralski silicon crystal growth based on global 3D numerical simulation
Power consumption distribution and heat transfer paths in Czochralski silicon crystal growth.
- 11 September 2024
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 26 (39) , 5531-5540
Study on power consumption and heat transfer paths in Czochralski silicon crystal growth based on global 3D numerical simulation
Power consumption distribution and heat transfer paths in Czochralski silicon crystal growth.