Radovan Drazumeric
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Radovan Drazumeric has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Peter Krajnik
Department of Industrial and Materials Science, Chalmers University of Technology, Gothenburg, Sweden
16 shared publications Jeffrey Badger
Int Grinding Inst, San Antonio, TX USA
9 shared publicationsFranc Kosel
Faculty of Mechanical Engineering, University of Ljubljana, Ljubljana, Slovenia
4 shared publicationsJeffrey A. Badger
4 shared publicationsPier Marzocca
4 shared publicationsBojan Gjerek
3 shared publications
Latest Publications
- Open Access
- 18 September 2024
- Published by IntechOpen
Optimization of industrial grinding processes using the Theory of Aggressiveness: case studies from real-world manufacturing
In the first 60 years of grinding research (1914–1974), various dimensionless parameters were introduced to account for the fundamental mechanics of an abrasive contact. Later, these parameters were superseded by various chip-thickness models, which required the difficult and often ambiguous quantification of grinding-wheel topography. The first-principles approach has recently re-emerged via the grand-unifying Theory of Aggressiveness and the practical aggressiveness number, a dimensionless parameter that has proved to be powerful in optimizing any arbitrary abrasive process, including grinding and truing/dressing. It has now gained wider popularity and use because of its ability to capture the fundamental process geometry and kinematics while circumventing the need to quantify the wheel topography. This paper reviews the use of the dimensionless aggressiveness number in several case studies from real production, demonstrating how the concept can be used to optimize industrial processes, including camshaft and crankshaft grinding, saw-tip grinding, flute grinding, double-disc grinding, and diamond-wheel truing.
- 18 September 2024
- Published by IntechOpen
Open AccessOptimization of industrial grinding processes using the Theory of Aggressiveness: case studies from real-world manufacturing
In the first 60 years of grinding research (1914–1974), various dimensionless parameters were introduced to account for the fundamental mechanics of an abrasive contact. Later, these parameters were superseded by various chip-thickness models, which required the difficult and often ambiguous quantification of grinding-wheel topography. The first-principles approach has recently re-emerged via the grand-unifying Theory of Aggressiveness and the practical aggressiveness number, a dimensionless parameter that has proved to be powerful in optimizing any arbitrary abrasive process, including grinding and truing/dressing. It has now gained wider popularity and use because of its ability to capture the fundamental process geometry and kinematics while circumventing the need to quantify the wheel topography. This paper reviews the use of the dimensionless aggressiveness number in several case studies from real production, demonstrating how the concept can be used to optimize industrial processes, including camshaft and crankshaft grinding, saw-tip grinding, flute grinding, double-disc grinding, and diamond-wheel truing.
- Open Access
- 19 July 2022
- Published by Elsevier in International Journal of Machine Tools and Manufacture
- Vol. 180, 103919
The effects of grit properties and dressing on grinding mechanics and wheel performance: Analytical assessment framework
- 19 July 2022
- Published by Elsevier in International Journal of Machine Tools and Manufacture
- Vol. 180, 103919
Open AccessThe effects of grit properties and dressing on grinding mechanics and wheel performance: Analytical assessment framework
- 1 September 2018
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 259, 228-234
Temperature-based method for determination of feed increments in crankshaft grinding
- 1 September 2018
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 259, 228-234
Temperature-based method for determination of feed increments in crankshaft grinding
- Open Access
- 1 July 2018
- Published by Elsevier in Aerospace Science and Technology
- Vol. 78, 71-88
Assessment of low-fidelity fluid–structure interaction model for flexible propeller blades
- 1 July 2018
- Published by Elsevier in Aerospace Science and Technology
- Vol. 78, 71-88
Open AccessAssessment of low-fidelity fluid–structure interaction model for flexible propeller blades
- 1 January 2018
- Published by Elsevier in CIRP Annals
- Vol. 67 (1) , 345-348
Truing of diamond wheels – Geometry, kinematics and removal mechanisms
- 1 January 2018
- Published by Elsevier in CIRP Annals
- Vol. 67 (1) , 345-348
Truing of diamond wheels – Geometry, kinematics and removal mechanisms
- 1 January 2017
- Published by Inderscience Publishers in International Journal of Abrasive Technology
- Vol. 8 (2) , 97
Wheel lift-off in creep-feed grinding: thermal damage, power surge, chip thickness and optimisation
An investigation is made into the phenomenon of early lift-off in creep-feed grinding, where the wheel lifts away from the workpiece before reaching the end of cut. In single-pass operations, early lift-off can result in thermal damage. In multi-pass operations, there is a surge in material-removal rate just before lift-off, which can result in thermal damage and excess wheel wear. This study examines the current inadequate methods of dealing with lift-off. It then develops a geometric and kinematic model for analysing the lift-off phenomenon. It finally proposes a thermal-model-based optimisation method for achieving a constant maximum surface temperature, resulting in shorter cycle times and less risk of thermal damage. The power-surge model is validated experimentally in diamond grinding of tungsten-carbide rotary tools.
- 1 January 2017
- Published by Inderscience Publishers in International Journal of Abrasive Technology
- Vol. 8 (2) , 97
Wheel lift-off in creep-feed grinding: thermal damage, power surge, chip thickness and optimisation
An investigation is made into the phenomenon of early lift-off in creep-feed grinding, where the wheel lifts away from the workpiece before reaching the end of cut. In single-pass operations, early lift-off can result in thermal damage. In multi-pass operations, there is a surge in material-removal rate just before lift-off, which can result in thermal damage and excess wheel wear. This study examines the current inadequate methods of dealing with lift-off. It then develops a geometric and kinematic model for analysing the lift-off phenomenon. It finally proposes a thermal-model-based optimisation method for achieving a constant maximum surface temperature, resulting in shorter cycle times and less risk of thermal damage. The power-surge model is validated experimentally in diamond grinding of tungsten-carbide rotary tools.
- 1 January 2017
- Published by Inderscience Publishers in International Journal of Abrasive Technology
- Vol. 8 (2) , 97
Wheel lift-off in creep-feed grinding: thermal damage, power surge, chip thickness and optimisation
An investigation is made into the phenomenon of early lift-off in creep-feed grinding, where the wheel lifts away from the workpiece before reaching the end of cut. In single-pass operations, early lift-off can result in thermal damage. In multi-pass operations, there is a surge in material-removal rate just before lift-off, which can result in thermal damage and excess wheel wear. This study examines the current inadequate methods of dealing with lift-off. It then develops a geometric and kinematic model for analysing the lift-off phenomenon. It finally proposes a thermal-model-based optimisation method for achieving a constant maximum surface temperature, resulting in shorter cycle times and less risk of thermal damage. The power-surge model is validated experimentally in diamond grinding of tungsten-carbide rotary tools.
- 1 January 2017
- Published by Inderscience Publishers in International Journal of Abrasive Technology
- Vol. 8 (2) , 97
Wheel lift-off in creep-feed grinding: thermal damage, power surge, chip thickness and optimisation
An investigation is made into the phenomenon of early lift-off in creep-feed grinding, where the wheel lifts away from the workpiece before reaching the end of cut. In single-pass operations, early lift-off can result in thermal damage. In multi-pass operations, there is a surge in material-removal rate just before lift-off, which can result in thermal damage and excess wheel wear. This study examines the current inadequate methods of dealing with lift-off. It then develops a geometric and kinematic model for analysing the lift-off phenomenon. It finally proposes a thermal-model-based optimisation method for achieving a constant maximum surface temperature, resulting in shorter cycle times and less risk of thermal damage. The power-surge model is validated experimentally in diamond grinding of tungsten-carbide rotary tools.
- 1 October 2016
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 874, 115-123
Grinding of Cermets with Cup-Wheels
Cup-wheels are frequently used to grind cermets, a difficult-to-grind material. An investigation was made into the transient geometry of the cup-wheel rim, grit dulling, wheel loading, and wheel self-sharpening with chip thickness. Tests were performed on a saw-tip grinding machine and specific energies, G-ratios and rim geometries were measured. Results showed that, like grinding of tungsten-carbide, loading is prevalent. However, unlike grinding of tungsten-carbide, grit dulling is also prevalent and wheel conditioning is of limited use. Much better results, particularly with respect to surface finish, can be obtained if the wheel is trued to a predetermined geometry. In addition, grinding parameters must be chosen to induce wheel self-sharpening. Practical recommendations are given.
- 1 October 2016
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 874, 115-123
Grinding of Cermets with Cup-Wheels
Cup-wheels are frequently used to grind cermets, a difficult-to-grind material. An investigation was made into the transient geometry of the cup-wheel rim, grit dulling, wheel loading, and wheel self-sharpening with chip thickness. Tests were performed on a saw-tip grinding machine and specific energies, G-ratios and rim geometries were measured. Results showed that, like grinding of tungsten-carbide, loading is prevalent. However, unlike grinding of tungsten-carbide, grit dulling is also prevalent and wheel conditioning is of limited use. Much better results, particularly with respect to surface finish, can be obtained if the wheel is trued to a predetermined geometry. In addition, grinding parameters must be chosen to induce wheel self-sharpening. Practical recommendations are given.
- 25 May 2016
- Published by Springer Nature in Structural and Multidisciplinary Optimization
- Vol. 55 (1) , 91-104
Structural optimization using global stress-deviation objective function via the level-set method
- 25 May 2016
- Published by Springer Nature in Structural and Multidisciplinary Optimization
- Vol. 55 (1) , 91-104
Structural optimization using global stress-deviation objective function via the level-set method
- 28 January 2016
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 231 (12) , 2103-2111
The use of computational fluid dynamics in the analysis of fluid flow and thermal aspects in grinding
A numerical model based on computational fluid dynamics is developed to analyze fluid flow and thermal aspects in grinding. The model uses multiphase fluid flow with heat transfer based on the volume-of-fluid method, convection, conduction in solids and a multiple reference frame model of the porous grinding zone. Fluid velocity vectors, useful flow rate, grinding temperatures and energy partition are predicted using the model. In lieu of direct measurements of these quantities, the verification relies on the indirect assessment of surface integrity. The simulation results provide adequate agreement with the measured residual stress, depth of heat-affected zone and full width at half maximum profile with respect to the grinding temperatures.
- 28 January 2016
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 231 (12) , 2103-2111
The use of computational fluid dynamics in the analysis of fluid flow and thermal aspects in grinding
A numerical model based on computational fluid dynamics is developed to analyze fluid flow and thermal aspects in grinding. The model uses multiphase fluid flow with heat transfer based on the volume-of-fluid method, convection, conduction in solids and a multiple reference frame model of the porous grinding zone. Fluid velocity vectors, useful flow rate, grinding temperatures and energy partition are predicted using the model. In lieu of direct measurements of these quantities, the verification relies on the indirect assessment of surface integrity. The simulation results provide adequate agreement with the measured residual stress, depth of heat-affected zone and full width at half maximum profile with respect to the grinding temperatures.