Hakan Keskin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Hakan Keskin has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
Musa Atar
Gazi University
14 shared publications- Musa Atar
Gazi Üniversitesi
7 shared publications - Eyüp Aksoy
AFYON KOCATEPE ÜNİVERSİTESİ, AFYON MESLEK YÜKSEKOKULU
4 shared publications - Ahmet Cihangir Yalinkiliç
Kutahya Dumlupınar University, Department of Industrial Design Engineering, Kutahya, Turkiye
3 shared publications - Ramazan Bülbül
Gazi Üniversitesi
3 shared publications - Süleyman Korkut
Düzce University
3 shared publications
Latest Publications
- 31 December 2025
- Published by Yozgat Bozok University - Faculty of Engineering and Architecture in Bozok Journal of Engineering and Architecture
- Vol. 4 (2) , 51-61
Ayçiçek Sapı (Helianthus annuus L.) ile Odun Talaşından Üretilen Ahşap Panelin (ASP) Ses / Gürültü Yalıtım Özellikleri
Bu çalışmada, ülkemizde yaygın olarak üretilen ayçiçeğinin zirai atığı olan ayçiçek sapı (Helianthus annuus L.) ile kaba odun talaşından üretilen ahşap panelin ses / gürültü yalıtım özelliklerinin belirlenmesi amacıyla yapılmıştır. Deneylerde çerçeve konstrüksiyonlu, içi yalıtım malzemesi dolgulu, ön ve arka yüzü kayın kontrplak kaplı yeni bir ASP (ayçiçeği sapı + kaba odun talaşı) ahşap panel üretilmiştir. Karşılaştırma amacıyla, piyasada yaygın olarak kullanılan yalıtım malzemelerinden strafor ile camyünü dolgu tercih edilerek rijit, iki farklı panel örneği daha üretilmiştir. Üretilen ahşap panelin fiziksel özellikleri; yoğunluk TS ISO 13061-2, rutubet TS ISO 13061-2, ses yalıtım değeri TS EN ISO 16283-1 standartları esaslarına göre belirlenmiştir. Deneyler sonunda, ASP panelin hava kurusu yoğunluk değeri 0,419 g/cm3, rutubet değeri %10,318, ses yalıtım değeri A-frekans ağırlıklı (dBA) ölçümünde, gürültü kaynağı dışarda iken içerde 1m uzak mesafede yapılan ölçümde 65,9 dBA bulunmuştur. Gürültü kaynağı içerde iken dış ortamda 1m uzak mesafede yapılan ölçümde 64,7dBA, bulunmuştur. Bu sonuçlara göre ASP panel ses yalıtımının düşük gürültü ses seviyesi olan iç mekanlarda kullanılması önerilebilir.
- 31 December 2025
- Published by Yozgat Bozok University - Faculty of Engineering and Architecture in Bozok Journal of Engineering and Architecture
- Vol. 4 (2) , 51-61
Ayçiçek Sapı (Helianthus annuus L.) ile Odun Talaşından Üretilen Ahşap Panelin (ASP) Ses / Gürültü Yalıtım Özellikleri
Bu çalışmada, ülkemizde yaygın olarak üretilen ayçiçeğinin zirai atığı olan ayçiçek sapı (Helianthus annuus L.) ile kaba odun talaşından üretilen ahşap panelin ses / gürültü yalıtım özelliklerinin belirlenmesi amacıyla yapılmıştır. Deneylerde çerçeve konstrüksiyonlu, içi yalıtım malzemesi dolgulu, ön ve arka yüzü kayın kontrplak kaplı yeni bir ASP (ayçiçeği sapı + kaba odun talaşı) ahşap panel üretilmiştir. Karşılaştırma amacıyla, piyasada yaygın olarak kullanılan yalıtım malzemelerinden strafor ile camyünü dolgu tercih edilerek rijit, iki farklı panel örneği daha üretilmiştir. Üretilen ahşap panelin fiziksel özellikleri; yoğunluk TS ISO 13061-2, rutubet TS ISO 13061-2, ses yalıtım değeri TS EN ISO 16283-1 standartları esaslarına göre belirlenmiştir. Deneyler sonunda, ASP panelin hava kurusu yoğunluk değeri 0,419 g/cm3, rutubet değeri %10,318, ses yalıtım değeri A-frekans ağırlıklı (dBA) ölçümünde, gürültü kaynağı dışarda iken içerde 1m uzak mesafede yapılan ölçümde 65,9 dBA bulunmuştur. Gürültü kaynağı içerde iken dış ortamda 1m uzak mesafede yapılan ölçümde 64,7dBA, bulunmuştur. Bu sonuçlara göre ASP panel ses yalıtımının düşük gürültü ses seviyesi olan iç mekanlarda kullanılması önerilebilir.
- Open Access
- 4 December 2025
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 28 (6) , 1555-1562
Verniklenmiş Ahşap Lavabo ve Küvetlerde Verniklerin Yüzeye Yapışma ve Sertlik Değerine Yaşlandırma İşleminin Etkisi
Bu çalışma, verniklenmiş ahşap lavabo ve küvetlerde uzun ve kısa süreli yaşlandırma işleminin verniklerin yüzeye yapışma ve sertlik değerine etkilerini belirlemek amacı ile yapılmıştır. Bu maksatla sapsız meşe ve irokodan hazırlanan deney örnek yüzeylerine epoksi uygulama sonrası üzerine ASTM D 3023’e göre selülozik ve akrilik vernik atılmıştır. Hazırlanan sapsız meşe (Quercus petraea Liebl.) ve iroko (Chlorophora excelsa) örnekleri UVB - 313 lambalarına sahip cihazda 252 ve 504 saat, yapay yaşlandırmaya tabi tutulmuştur. Yaşlandırma sonrası test örneklerinde ASTM D 4366 – 95’e göre vernik yüzey sertliği ve TS EN ISO 4624 standardı esaslarına göre yapışma değeri belirlenmiştir. Sonuç olarak; yüzey sertlik değeri, malzeme çeşidi bakımından en yüksek, meşe (40,31), selülozik vernik (41,03) ve uzun sürede (54,50), en düşük, iroko (33,94), akrilik vernik (33,22), kısa sürede (38,04) bulunmuştur. Çoklu etkileşimde en yüksek meşe + selülozik vernik + uzun süre (63,67), en düşük iroko + akrilik vernik + kısa sürede (27,67) çıkmıştır. Yüzey yapışma değeri(Newton) malzeme çeşidi bakımından en yüksek meşe (370,47 N), selülozik vernik (360,36 N), kısa sürede (340,29 N), en düşük iroko (310,28 N), akrilik vernik (320,39 N), uzun sürede (310,88 N) elde edilmiştir. Çoklu etkileşimde, yüzeye yapışma değeri, en yüksek meşe + akrilik vernik + kısa süre (460,67 N), en düşük iroko + akrilik vernik + uzun sürede (160,17 N) tespit edilmiştir. Küvet ve lavaboda ahşap kullanılması halinde su ve neme karşı dayanımını artırmak için bazı işlemlerden geçirilmesi gereklidir. Araştırmada elde edilen bu değerlerin, ahşap lavabo ve küvet yapımında göz önünde bulundurulması, ürünlerin kullanım ömürleri bakımından avantaj sağlayabilir.
- 4 December 2025
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 28 (6) , 1555-1562
Open AccessVerniklenmiş Ahşap Lavabo ve Küvetlerde Verniklerin Yüzeye Yapışma ve Sertlik Değerine Yaşlandırma İşleminin Etkisi
Bu çalışma, verniklenmiş ahşap lavabo ve küvetlerde uzun ve kısa süreli yaşlandırma işleminin verniklerin yüzeye yapışma ve sertlik değerine etkilerini belirlemek amacı ile yapılmıştır. Bu maksatla sapsız meşe ve irokodan hazırlanan deney örnek yüzeylerine epoksi uygulama sonrası üzerine ASTM D 3023’e göre selülozik ve akrilik vernik atılmıştır. Hazırlanan sapsız meşe (Quercus petraea Liebl.) ve iroko (Chlorophora excelsa) örnekleri UVB - 313 lambalarına sahip cihazda 252 ve 504 saat, yapay yaşlandırmaya tabi tutulmuştur. Yaşlandırma sonrası test örneklerinde ASTM D 4366 – 95’e göre vernik yüzey sertliği ve TS EN ISO 4624 standardı esaslarına göre yapışma değeri belirlenmiştir. Sonuç olarak; yüzey sertlik değeri, malzeme çeşidi bakımından en yüksek, meşe (40,31), selülozik vernik (41,03) ve uzun sürede (54,50), en düşük, iroko (33,94), akrilik vernik (33,22), kısa sürede (38,04) bulunmuştur. Çoklu etkileşimde en yüksek meşe + selülozik vernik + uzun süre (63,67), en düşük iroko + akrilik vernik + kısa sürede (27,67) çıkmıştır. Yüzey yapışma değeri(Newton) malzeme çeşidi bakımından en yüksek meşe (370,47 N), selülozik vernik (360,36 N), kısa sürede (340,29 N), en düşük iroko (310,28 N), akrilik vernik (320,39 N), uzun sürede (310,88 N) elde edilmiştir. Çoklu etkileşimde, yüzeye yapışma değeri, en yüksek meşe + akrilik vernik + kısa süre (460,67 N), en düşük iroko + akrilik vernik + uzun sürede (160,17 N) tespit edilmiştir. Küvet ve lavaboda ahşap kullanılması halinde su ve neme karşı dayanımını artırmak için bazı işlemlerden geçirilmesi gereklidir. Araştırmada elde edilen bu değerlerin, ahşap lavabo ve küvet yapımında göz önünde bulundurulması, ürünlerin kullanım ömürleri bakımından avantaj sağlayabilir.
- 25 June 2025
- Published by Lukasiewicz Research Network - Poznan Technology Institute in Drewno. Prace Naukowe, Doniesienia, Komunikaty = Wood. Research Papers, Reports, Announcements
Enhancing the Thermal and Acoustic Performance of Cross Laminated Timber Panels through Perforation Technique
The increasing need for energy-efficient and acoustically optimized buildings has positioned cross-laminated timber (CLT) as a competitive material in sustainable construction. This study investigates the impact of perforation techniques on the thermal and acoustic performance of CLT panels produced from Scots Pine (Pinus sylvestris L.), Uludağ Fir (Abies bornmülleriana Mattf.), and Sessile Oak (Quercus petraea L.). Panels were manufactured in three- and five-layer configurations, incorporating perforation ratios of 10% and 20% in the internal layers. Experimental results demonstrated that increasing perforation ratios led to a decrease in thermal conductivity and transmittance, while significantly improving sound absorption coefficients. For instance, panels with 20% perforation exhibited a notable reduction in sound transmission, contributing to enhanced indoor acoustic comfort. These findings underline the potential of perforated CLT panels as multifunctional elements in both residential and commercial buildings. The study highlights the potential global impact of integrating such material innovations into sustainable construction practices, particularly in urban environments demanding high thermal efficiency and noise control.
- 25 June 2025
- Published by Lukasiewicz Research Network - Poznan Technology Institute in Drewno. Prace Naukowe, Doniesienia, Komunikaty = Wood. Research Papers, Reports, Announcements
Enhancing the Thermal and Acoustic Performance of Cross Laminated Timber Panels through Perforation Technique
The increasing need for energy-efficient and acoustically optimized buildings has positioned cross-laminated timber (CLT) as a competitive material in sustainable construction. This study investigates the impact of perforation techniques on the thermal and acoustic performance of CLT panels produced from Scots Pine (Pinus sylvestris L.), Uludağ Fir (Abies bornmülleriana Mattf.), and Sessile Oak (Quercus petraea L.). Panels were manufactured in three- and five-layer configurations, incorporating perforation ratios of 10% and 20% in the internal layers. Experimental results demonstrated that increasing perforation ratios led to a decrease in thermal conductivity and transmittance, while significantly improving sound absorption coefficients. For instance, panels with 20% perforation exhibited a notable reduction in sound transmission, contributing to enhanced indoor acoustic comfort. These findings underline the potential of perforated CLT panels as multifunctional elements in both residential and commercial buildings. The study highlights the potential global impact of integrating such material innovations into sustainable construction practices, particularly in urban environments demanding high thermal efficiency and noise control.
- 30 December 2024
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 7 (2) , 172-187
Ahşap ve ahşap esaslı levhalara uygulanan boyaların yanmada ışık yoğunluğuna etkisi
Bu çalışma, çeşitli örtücü ahşap boyaların ağaç malzeme ve levhalarda yanmada ışık yoğunluğuna etkilerini belirlemek amacı ile yapılmıştır. Bu maksatla Doğu kayını (Fagus oriantalis L.), sarıçam (Pinus silvestris L.), sapsız meşe (Quercus petraea L.) orta yoğunlukta lif levha (MDF) ve yonga levhadan hazırlanan, örnekler akrilik, sentetik ve selülozik boya (lake boya) ile ASTM-D-3023’e göre boyanmıştır. Örneklerin yanmada ışık yoğunlukları ASTM E 160–50 esaslarına göre belirlenmiştir. Işık yoğunluğu; malzeme çeşidine göre en yüksek Doğu kayınında, en düşük yonga levhada, boya çeşidine göre en yüksek akrilik boyada, en düşük sentetik boyada belirlenmiştir. Işık yoğunluğu; kendi kendine yanmada malzeme çeşidine göre en yüksek yonga levhada (865,3), en düşük sarıçamda (839,5), malzeme türü, boya çeşidi ve kat sayısı etkileşimine göre en yüksek YL+Ab+I’de (tek kat akrilik boya ile boyanmış yonga levha) (888,2), en düşük Sç+Sb+II’de (iki kat selülozik boya ile boyanmış sarıçam) (776,4) belirlenmiştir. Buna göre, araştırması yapılan malzemelerin dekorasyonda uygulanmasının düşünülmesi halinde, yangında dumandan boğulma tehlikesine karşı en uygun ve daha düşük risk içeren dekorasyon elemanının yonga levhadan yapılmış ve akrilik boya ile boyanmış materyaller olacağı tespit edilmiştir. Bu durum, yangın riski bulanan mekânlarda burada bulunan sonuçların dikkate alınarak uygulanması can emniyeti bakımından avantaj sağlayacağı söylenebilir.
- 30 December 2024
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 7 (2) , 172-187
Ahşap ve ahşap esaslı levhalara uygulanan boyaların yanmada ışık yoğunluğuna etkisi
Bu çalışma, çeşitli örtücü ahşap boyaların ağaç malzeme ve levhalarda yanmada ışık yoğunluğuna etkilerini belirlemek amacı ile yapılmıştır. Bu maksatla Doğu kayını (Fagus oriantalis L.), sarıçam (Pinus silvestris L.), sapsız meşe (Quercus petraea L.) orta yoğunlukta lif levha (MDF) ve yonga levhadan hazırlanan, örnekler akrilik, sentetik ve selülozik boya (lake boya) ile ASTM-D-3023’e göre boyanmıştır. Örneklerin yanmada ışık yoğunlukları ASTM E 160–50 esaslarına göre belirlenmiştir. Işık yoğunluğu; malzeme çeşidine göre en yüksek Doğu kayınında, en düşük yonga levhada, boya çeşidine göre en yüksek akrilik boyada, en düşük sentetik boyada belirlenmiştir. Işık yoğunluğu; kendi kendine yanmada malzeme çeşidine göre en yüksek yonga levhada (865,3), en düşük sarıçamda (839,5), malzeme türü, boya çeşidi ve kat sayısı etkileşimine göre en yüksek YL+Ab+I’de (tek kat akrilik boya ile boyanmış yonga levha) (888,2), en düşük Sç+Sb+II’de (iki kat selülozik boya ile boyanmış sarıçam) (776,4) belirlenmiştir. Buna göre, araştırması yapılan malzemelerin dekorasyonda uygulanmasının düşünülmesi halinde, yangında dumandan boğulma tehlikesine karşı en uygun ve daha düşük risk içeren dekorasyon elemanının yonga levhadan yapılmış ve akrilik boya ile boyanmış materyaller olacağı tespit edilmiştir. Bu durum, yangın riski bulanan mekânlarda burada bulunan sonuçların dikkate alınarak uygulanması can emniyeti bakımından avantaj sağlayacağı söylenebilir.
- 29 December 2023
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 6 (2) , 175-182
Farklı perforelerle oluşturulan çapraz lamine ahşap levhaların (CLT) ısı iletkenlik değerlerinin belirlenmesi
Bu çalışmada, orman ürünleri sanayisinde yaygın bir kullanım alanına sahip olan sarıçam (Pinus silvestris L.) odunundan; kontrol grubu ile ara katmanlarda perforasyon oranları sırasıyla %5, %10 ve %20 olmak üzere 45 mm kalınlıkta, üç katmanlı çapraz lamine ahşap levhalar (CLT) oluşturulmuştur. Çapraz lamine ahşap levhaların ara katmanını oluşturan masif levhanın yüzeyine belirtilmiş olan oranlarda ve Ø10 mm çapında perforasyon işlemi yapılmış ve her iki yüzeyine tutkal sürüldükten sonra preslenerek çapraz lamine levha üretilmiştir. Çalışma kapsamında üretilen çapraz lamine ahşap levhaların TSE EN 322’ye göre rutubet miktarının tayini, TS EN 323’e göre yoğunlukları, TS EN 12667’ ye göre ise ısı iletim katsayıları tespit edilmiştir. Yapılan deneylerden elde edilen verilere göre, çapraz lamine ahşap levhaların (CLT) ara katmanlarına belirtilmiş olan oranlarda yapılan perforasyon uygulamasında ısı iletim katsayılarında kontrol grubuna kıyasla %1.05, %4.56 ve %9.73 oranında azalma meydana geldiği ve bu azalmanın da istatistiksel olarak anlamlı olduğu görülmüştür. Ara katmanlarda uygulanan perforasyon işleminin anlamlı olan etki düzeyinin daha yüksek olması için ara katmandaki levhanın daha düşük yoğunluğa sahip masif ahşap malzemelerden yapılması ve perforasyon işleminin ise CNC makinelerinde uygulanması önerilmektedir.
- 29 December 2023
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 6 (2) , 175-182
Farklı perforelerle oluşturulan çapraz lamine ahşap levhaların (CLT) ısı iletkenlik değerlerinin belirlenmesi
Bu çalışmada, orman ürünleri sanayisinde yaygın bir kullanım alanına sahip olan sarıçam (Pinus silvestris L.) odunundan; kontrol grubu ile ara katmanlarda perforasyon oranları sırasıyla %5, %10 ve %20 olmak üzere 45 mm kalınlıkta, üç katmanlı çapraz lamine ahşap levhalar (CLT) oluşturulmuştur. Çapraz lamine ahşap levhaların ara katmanını oluşturan masif levhanın yüzeyine belirtilmiş olan oranlarda ve Ø10 mm çapında perforasyon işlemi yapılmış ve her iki yüzeyine tutkal sürüldükten sonra preslenerek çapraz lamine levha üretilmiştir. Çalışma kapsamında üretilen çapraz lamine ahşap levhaların TSE EN 322’ye göre rutubet miktarının tayini, TS EN 323’e göre yoğunlukları, TS EN 12667’ ye göre ise ısı iletim katsayıları tespit edilmiştir. Yapılan deneylerden elde edilen verilere göre, çapraz lamine ahşap levhaların (CLT) ara katmanlarına belirtilmiş olan oranlarda yapılan perforasyon uygulamasında ısı iletim katsayılarında kontrol grubuna kıyasla %1.05, %4.56 ve %9.73 oranında azalma meydana geldiği ve bu azalmanın da istatistiksel olarak anlamlı olduğu görülmüştür. Ara katmanlarda uygulanan perforasyon işleminin anlamlı olan etki düzeyinin daha yüksek olması için ara katmandaki levhanın daha düşük yoğunluğa sahip masif ahşap malzemelerden yapılması ve perforasyon işleminin ise CNC makinelerinde uygulanması önerilmektedir.
- 1 October 2022
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 25 (3) , 1157-1165
Mimaride Kullanılan Yonga Levhaların Kolofan Katkılı Borlu Bileşikler ile Yangın Dayanımının Artırılması
One of the important factors that should be considered in architecture is the fire resistance of the materials used. This study, it is aimed to increase the fire resistance of particleboards, which are widely used in architecture. For this purpose, it is aimed to improve the fire resistance by using a new type of impregnation material obtained by modifying boron compounds with rosin additive. Within this context, particleboard samples prepared in accordance with TS 642 ISO 554 were sized according to ASTM-E 160-50. Combustion tests of prepared samples were done in accordance with ASTM-E 160-50 E, and the values obtained through the tests on the basis of burning time, weight loss ratios, FsC, SC, Gp temperatures were compared with the control samples. As a result, it was observed that average temperature values of FsC, SC decreased by 5%, Gp decreased by 1,8%, weight loss was reduced by 0,5% and the combustion period was increased by 2%. This case can be taken into account in the field where particleboard is used with high fire risk in architecture.
- 1 October 2022
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 25 (3) , 1157-1165
Mimaride Kullanılan Yonga Levhaların Kolofan Katkılı Borlu Bileşikler ile Yangın Dayanımının Artırılması
One of the important factors that should be considered in architecture is the fire resistance of the materials used. This study, it is aimed to increase the fire resistance of particleboards, which are widely used in architecture. For this purpose, it is aimed to improve the fire resistance by using a new type of impregnation material obtained by modifying boron compounds with rosin additive. Within this context, particleboard samples prepared in accordance with TS 642 ISO 554 were sized according to ASTM-E 160-50. Combustion tests of prepared samples were done in accordance with ASTM-E 160-50 E, and the values obtained through the tests on the basis of burning time, weight loss ratios, FsC, SC, Gp temperatures were compared with the control samples. As a result, it was observed that average temperature values of FsC, SC decreased by 5%, Gp decreased by 1,8%, weight loss was reduced by 0,5% and the combustion period was increased by 2%. This case can be taken into account in the field where particleboard is used with high fire risk in architecture.
- 1 December 2021
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 24 (4) , 1525-1532
Impacts of the Bleaching and Varnishing Process on the Glow State Combustion Temperature of Some Wood Materials, Part 2
This study was carried out to determine the impact of bleaching and varnishing on the glow-combustion temperature of wood material. For this purpose, specimens prepared according to ASTM D 358 from European Oak, Oriental beech and Scotch pine wood are bleached with a solution of 18% sodium hydroxide (NaOH), hydrogen peroxide (H2O2), calcium hydroxide (CaOH2), sodium silicate (NaSiO3), acetic acid (CH3COOH), sodium disulfide (Na2S2O5), oxalic acid (H2C2O4) and potassium permanganate (KMnO4). The bleached specimens are varnished with synthetic (Sn) waterborne (Sb), polyurethane (Pu) and acrylic (Av) in accordance with ASTM D 3023. The glow state combustion properties were determined in accordance with ASTM E 160-50. Consequently, the glow state combustion temperature; wood species, bleaching materials and varnish types of open interaction European oak+R-3+Synthetic varnish according to the highest, the lowest oriental beech+R-1+su bazli varnish at were obtained. Accordingly, the desired fireproof in the wood product applications made of European oak wood, bleached with R-3 (NaSiO3+H2O2) and coated with a synthetic varnish, use may be recommended.
- 1 December 2021
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 24 (4) , 1525-1532
Impacts of the Bleaching and Varnishing Process on the Glow State Combustion Temperature of Some Wood Materials, Part 2
This study was carried out to determine the impact of bleaching and varnishing on the glow-combustion temperature of wood material. For this purpose, specimens prepared according to ASTM D 358 from European Oak, Oriental beech and Scotch pine wood are bleached with a solution of 18% sodium hydroxide (NaOH), hydrogen peroxide (H2O2), calcium hydroxide (CaOH2), sodium silicate (NaSiO3), acetic acid (CH3COOH), sodium disulfide (Na2S2O5), oxalic acid (H2C2O4) and potassium permanganate (KMnO4). The bleached specimens are varnished with synthetic (Sn) waterborne (Sb), polyurethane (Pu) and acrylic (Av) in accordance with ASTM D 3023. The glow state combustion properties were determined in accordance with ASTM E 160-50. Consequently, the glow state combustion temperature; wood species, bleaching materials and varnish types of open interaction European oak+R-3+Synthetic varnish according to the highest, the lowest oriental beech+R-1+su bazli varnish at were obtained. Accordingly, the desired fireproof in the wood product applications made of European oak wood, bleached with R-3 (NaSiO3+H2O2) and coated with a synthetic varnish, use may be recommended.
- 1 June 2021
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 24 (2) , 655-662
Effect of Impregnation with Boron Compound Doped Rosin to the Combustion Resistance of Oriental Beech Wood (Fagus orientalis Lipsky)
Tr en In this study, investigation of the combustion properties of Oriental beech wood (Fagus orientalis Lipsky) impregnated with boron compound (borax (Na2B4O710H2O), boric acid (H3BO3) doped rosin (C19H29COOH) was aimed. For this purpose, Oriental beech wood samples were prepared according to ASTM E 160-50 and impregnated with boron compound doped rosin by the method of medium-term dipping (24 hours) according to ASTM D 1413 and producers’ definition. Combustion properties of samples after impregnated process were determined according to ASTM E 160-50. As a part of the research, 6 different combination and contents of impregnation materials have been used in order to especially investigate resistance against combustion of wood material treated with boron compounds in different concentrations. As a result of the study, retention performance and leaching resistance of boron compounds can be increased through rosin addition. Consequently, impregnation materials with rosin decreased the flame sourced combustion (Fsc) temperatures depending on kind of impregnation material, extended combustion period and decreased weight loss ratio of the test samples in comparison to the control samples. On the contrary, weight loss ratios were affected negatively in Oriental beech test samples up to 3% when compared with samples which were impregnated with borax. Meanwhile, combustion periods increased in test samples up to 30%. Rosin, in terms of its combustion performance, can be preferred in impregnation with boron compounds depending on kind of wood and using area. In this study, investigation of the combustion properties of Oriental beech wood (Fagus orientalis Lipsky) impregnated with boron compound (borax (Na2B4O710H2O), boric acid (H3BO3) doped rosin (C19H29COOH) was aimed. For this purpose, Oriental beech wood samples were prepared according to ASTM E 160-50 and impregnated with boron compound doped rosin by the method of medium-term dipping (24 hours) according to ASTM D 1413 and producers’ definition. Combustion properties of samples after impregnated process were determined according to ASTM E 160-50. As a part of the research, 6 different combination and contents of impregnation materials have been used in order to especially investigate resistance against combustion of wood material treated with boron compounds in different concentrations. As a result of the study, retention performance and leaching resistance of boron compounds can be increased through rosin addition. Consequently, impregnation materials with rosin decreased the flame sourced combustion (Fsc) temperatures depending on kind of impregnation material, extended combustion period and decreased weight loss ratio of the test samples in comparison to the control samples. On the contrary, weight loss ratios were affected negatively in Oriental beech test samples up to 3% when compared with samples which were impregnated with borax. Meanwhile, combustion periods increased in test samples up to 30%. Rosin, in terms of its combustion performance, can be preferred in impregnation with boron compounds depending on kind of wood and using area.
- 1 June 2021
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 24 (2) , 655-662
Effect of Impregnation with Boron Compound Doped Rosin to the Combustion Resistance of Oriental Beech Wood (Fagus orientalis Lipsky)
Tr en In this study, investigation of the combustion properties of Oriental beech wood (Fagus orientalis Lipsky) impregnated with boron compound (borax (Na2B4O710H2O), boric acid (H3BO3) doped rosin (C19H29COOH) was aimed. For this purpose, Oriental beech wood samples were prepared according to ASTM E 160-50 and impregnated with boron compound doped rosin by the method of medium-term dipping (24 hours) according to ASTM D 1413 and producers’ definition. Combustion properties of samples after impregnated process were determined according to ASTM E 160-50. As a part of the research, 6 different combination and contents of impregnation materials have been used in order to especially investigate resistance against combustion of wood material treated with boron compounds in different concentrations. As a result of the study, retention performance and leaching resistance of boron compounds can be increased through rosin addition. Consequently, impregnation materials with rosin decreased the flame sourced combustion (Fsc) temperatures depending on kind of impregnation material, extended combustion period and decreased weight loss ratio of the test samples in comparison to the control samples. On the contrary, weight loss ratios were affected negatively in Oriental beech test samples up to 3% when compared with samples which were impregnated with borax. Meanwhile, combustion periods increased in test samples up to 30%. Rosin, in terms of its combustion performance, can be preferred in impregnation with boron compounds depending on kind of wood and using area. In this study, investigation of the combustion properties of Oriental beech wood (Fagus orientalis Lipsky) impregnated with boron compound (borax (Na2B4O710H2O), boric acid (H3BO3) doped rosin (C19H29COOH) was aimed. For this purpose, Oriental beech wood samples were prepared according to ASTM E 160-50 and impregnated with boron compound doped rosin by the method of medium-term dipping (24 hours) according to ASTM D 1413 and producers’ definition. Combustion properties of samples after impregnated process were determined according to ASTM E 160-50. As a part of the research, 6 different combination and contents of impregnation materials have been used in order to especially investigate resistance against combustion of wood material treated with boron compounds in different concentrations. As a result of the study, retention performance and leaching resistance of boron compounds can be increased through rosin addition. Consequently, impregnation materials with rosin decreased the flame sourced combustion (Fsc) temperatures depending on kind of impregnation material, extended combustion period and decreased weight loss ratio of the test samples in comparison to the control samples. On the contrary, weight loss ratios were affected negatively in Oriental beech test samples up to 3% when compared with samples which were impregnated with borax. Meanwhile, combustion periods increased in test samples up to 30%. Rosin, in terms of its combustion performance, can be preferred in impregnation with boron compounds depending on kind of wood and using area.
- 1 June 2021
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 24 (2) , 637-643
Ağaç Malzemede Renk Açma ve Vernikleme İşleminin Yanmada Yıkılma Süresine Etkisi, Bölüm 1
Bu çalışma, ağaç malzemede renk açma ve vernikleme işleminin yanmada yıkılma süresine etkisini belirlemek amacıyla yapılmıştır. Bu maksatla; sapsız meşe (Quercus petraea Liebl.) odunundan ASTM D 358’e göre hazırlanan örnekler Sodyum hidroksit (NaOH), Hidrojen peroksit (H2O2), Kalsiyum hidroksit (Ca(OH)2) ve Sodyum silikat (NaSiO3)’ın %18’lik çözeltisi ile renk açma işlemi yapıldıktan sonra ASTM D 3023 esaslarına göre su bazlı (Sb), sentetik (Sn), poliüretan (Pu) ve akrilik vernikler (Av) ile kaplanmıştır. Hazırlanan örneklerin yanmada yıkılma süreleri ASTM E 160-50’ye göre belirlenmiştir. Sonuç olarak; yıkılma süresi (sn) vernik düzeyinde en yüksek akrilikte (1129 sn), en düşük sentetikte (651,1 sn), renk açma maddesi olarak en yüksek R3 (1114 sn) de, en düşük R2 (438 sn) de bulunmuştur. Renk açma çözeltisi ve vernik etkileşimine göre en yüksek Sb+R5 (1460 sn), en düşük Sn+R3 (840 sn) bulunmuştur. Buna göre yanmada yıkılmanın geç olması beklenen alanlarda bu durum dikkate alınabilir.
- 1 June 2021
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 24 (2) , 637-643
Ağaç Malzemede Renk Açma ve Vernikleme İşleminin Yanmada Yıkılma Süresine Etkisi, Bölüm 1
Bu çalışma, ağaç malzemede renk açma ve vernikleme işleminin yanmada yıkılma süresine etkisini belirlemek amacıyla yapılmıştır. Bu maksatla; sapsız meşe (Quercus petraea Liebl.) odunundan ASTM D 358’e göre hazırlanan örnekler Sodyum hidroksit (NaOH), Hidrojen peroksit (H2O2), Kalsiyum hidroksit (Ca(OH)2) ve Sodyum silikat (NaSiO3)’ın %18’lik çözeltisi ile renk açma işlemi yapıldıktan sonra ASTM D 3023 esaslarına göre su bazlı (Sb), sentetik (Sn), poliüretan (Pu) ve akrilik vernikler (Av) ile kaplanmıştır. Hazırlanan örneklerin yanmada yıkılma süreleri ASTM E 160-50’ye göre belirlenmiştir. Sonuç olarak; yıkılma süresi (sn) vernik düzeyinde en yüksek akrilikte (1129 sn), en düşük sentetikte (651,1 sn), renk açma maddesi olarak en yüksek R3 (1114 sn) de, en düşük R2 (438 sn) de bulunmuştur. Renk açma çözeltisi ve vernik etkileşimine göre en yüksek Sb+R5 (1460 sn), en düşük Sn+R3 (840 sn) bulunmuştur. Buna göre yanmada yıkılmanın geç olması beklenen alanlarda bu durum dikkate alınabilir.
- 1 March 2021
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 24 (1) , 103-112
Strengthening the Retention Amount and Leaching Resistance of Boron Compounds Used as Impregnation Material
This study is carried out in order to increase the retention performance of synthetic boron compounds. For this purpose, the test samples prepared from Scots pine (Pinus sylvestris Lipsky), European oak (Quercus petraea Liebl.) and Oriental Beech (Fagus orientalis Lipsky) woods and impregnated with dipping method in accordance with the principles of TS 6193 EN 84 by using 12 different composisiton of Developed Impregnation Liquid (DIL). The impregnated test materials are tested according to TS 6193 EN 84 principles. It has been found that the retention amount and leaching resistance of the DIL is approximately 2 times higher than the ones which are impregnated with boron compounds. DIL is more environmentally friendly than other toxic impregnation materials which are harmful for human health such as CCA beside its preservation feature against biotic and abiotic factors through boron compounds content. Moreoever the wood materials impregnated with DIL can be recycled comparatively more easily and in a healthy way at the end of economical lifetime.
- 1 March 2021
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 24 (1) , 103-112
Strengthening the Retention Amount and Leaching Resistance of Boron Compounds Used as Impregnation Material
This study is carried out in order to increase the retention performance of synthetic boron compounds. For this purpose, the test samples prepared from Scots pine (Pinus sylvestris Lipsky), European oak (Quercus petraea Liebl.) and Oriental Beech (Fagus orientalis Lipsky) woods and impregnated with dipping method in accordance with the principles of TS 6193 EN 84 by using 12 different composisiton of Developed Impregnation Liquid (DIL). The impregnated test materials are tested according to TS 6193 EN 84 principles. It has been found that the retention amount and leaching resistance of the DIL is approximately 2 times higher than the ones which are impregnated with boron compounds. DIL is more environmentally friendly than other toxic impregnation materials which are harmful for human health such as CCA beside its preservation feature against biotic and abiotic factors through boron compounds content. Moreoever the wood materials impregnated with DIL can be recycled comparatively more easily and in a healthy way at the end of economical lifetime.