Yaoxin Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yaoxin Zhang has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
Yafei Jia
12 shared publications- Yafei Jia
Univ. of Mississippi
11 shared publications - Mohammad Z. Al-Hamdan
Univ. of Mississippi
7 shared publications Sam S. Y. Wang
National Center for Computational Hydroscience and Engineering, 345 old Chemistry, The University of Mississippi, University, MS 38677
6 shared publicationsXiaobo Chao
Univ. of Mississippi
5 shared publications- Sam S. Y. Wang
The University of Mississippi
4 shared publications
Latest Publications
- 1 November 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Hydraulic Engineering
- Vol. 152 (6)
Numerical Study of Sediment Transport with Flow Hydrographs of Varying Length in a Laboratory Flume
This paper presents a numerical sediment transport model based on data from a series of experiments with flow hydrographs of varying lengths in a laboratory flume with a sand bed. The model was calibrated and validated using one flow hydrograph and then applied to other hydrographs. Digital flumes with different initial and boundary conditions were generated to assist numerical simulations and further explore additional scenarios, such as flow rates on the rising limb of the hydrograph, different sediment sizes, and longer hydrographs. Both numerical and experimental results demonstrate the influence of flow hydrograph duration on transport rates, which typically resulted in a counterclockwise hysteresis pattern. Different rising slopes of the flow rate had limited effects on the hysteresis pattern. Coarser sediment yielded lower transport rates, while finer particles led to increased transport rates, though neither caused appreciable changes to the hysteresis pattern. Limited sediment supply resulted in a change in hysteresis pattern from counterclockwise to figure-8. Longer hydrographs led to irregular hysteresis patterns due to the influence of bedforms that developed during peak flows.
- 1 November 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Hydraulic Engineering
- Vol. 152 (6)
Numerical Study of Sediment Transport with Flow Hydrographs of Varying Length in a Laboratory Flume
This paper presents a numerical sediment transport model based on data from a series of experiments with flow hydrographs of varying lengths in a laboratory flume with a sand bed. The model was calibrated and validated using one flow hydrograph and then applied to other hydrographs. Digital flumes with different initial and boundary conditions were generated to assist numerical simulations and further explore additional scenarios, such as flow rates on the rising limb of the hydrograph, different sediment sizes, and longer hydrographs. Both numerical and experimental results demonstrate the influence of flow hydrograph duration on transport rates, which typically resulted in a counterclockwise hysteresis pattern. Different rising slopes of the flow rate had limited effects on the hysteresis pattern. Coarser sediment yielded lower transport rates, while finer particles led to increased transport rates, though neither caused appreciable changes to the hysteresis pattern. Limited sediment supply resulted in a change in hysteresis pattern from counterclockwise to figure-8. Longer hydrographs led to irregular hysteresis patterns due to the influence of bedforms that developed during peak flows.
- Open Access
- 10 September 2026
- Published by Elsevier in Engineering Analysis with Boundary Elements
- Vol. 193
A virtual element method based on weak Galerkin formulation for groundwater flow with singular sources using meshfree shape functions
- 10 September 2026
- Published by Elsevier in Engineering Analysis with Boundary Elements
- Vol. 193
Open AccessA virtual element method based on weak Galerkin formulation for groundwater flow with singular sources using meshfree shape functions
- Open Access
- 12 July 2024
- Published by MDPI AG in Mathematics
- Vol. 12 (14) , 2184
Parallel Implicit Solvers for 2D Numerical Models on Structured Meshes
This paper presents the parallelization of two widely used implicit numerical solvers for the solution of partial differential equations on structured meshes, namely, the ADI (Alternating-Direction Implicit) solver for tridiagonal linear systems and the SIP (Strongly Implicit Procedure) solver for the penta-diagonal systems. Both solvers were parallelized using CUDA (Computer Unified Device Architecture) Fortran on GPGPUs (General-Purpose Graphics Processing Units). The parallel ADI solver (P-ADI) is based on the Parallel Cyclic Reduction (PCR) algorithm, while the parallel SIP solver (P-SIP) uses the wave front method (WF) following a diagonal line calculation strategy. To map the solution schemes onto the hierarchical block-threads framework of the CUDA on the GPU, the P-ADI solver adopted two mapping methods, one block thread with iterations (OBM-it) and multi-block threads (MBMs), while the P-SIP solver also used two mappings, one conventional mapping using effective WF lines (WF-e) with matrix coefficients and solution variables defined on original computational mesh, and a newly proposed mapping using all WF mesh (WF-all), on which matrix coefficients and solution variables are defined. Both the P-ADI and the P-SIP have been integrated into a two-dimensional (2D) hydrodynamic model, the CCHE2D (Center of Computational Hydroscience and Engineering) model, developed by the National Center for Computational Hydroscience and Engineering at the University of Mississippi. This study for the first time compared these two parallel solvers and their efficiency using examples and applications in complex geometries, which can provide valuable guidance for future uses of these two parallel implicit solvers in computational fluids dynamics (CFD). Both parallel solvers demonstrated higher efficiency than their serial counterparts on the CPU (Central Processing Unit): 3.73~4.98 speedup ratio for flow simulations, and 2.166~3.648 speedup ratio for sediment transport simulations. In general, the P-ADI solver is faster than but not as stable as the P-SIP solver; and for the P-SIP solver, the newly developed mapping method WF-all significantly improved the conventional mapping method WF-e.
- 12 July 2024
- Published by MDPI AG in Mathematics
- Vol. 12 (14) , 2184
Open AccessParallel Implicit Solvers for 2D Numerical Models on Structured Meshes
This paper presents the parallelization of two widely used implicit numerical solvers for the solution of partial differential equations on structured meshes, namely, the ADI (Alternating-Direction Implicit) solver for tridiagonal linear systems and the SIP (Strongly Implicit Procedure) solver for the penta-diagonal systems. Both solvers were parallelized using CUDA (Computer Unified Device Architecture) Fortran on GPGPUs (General-Purpose Graphics Processing Units). The parallel ADI solver (P-ADI) is based on the Parallel Cyclic Reduction (PCR) algorithm, while the parallel SIP solver (P-SIP) uses the wave front method (WF) following a diagonal line calculation strategy. To map the solution schemes onto the hierarchical block-threads framework of the CUDA on the GPU, the P-ADI solver adopted two mapping methods, one block thread with iterations (OBM-it) and multi-block threads (MBMs), while the P-SIP solver also used two mappings, one conventional mapping using effective WF lines (WF-e) with matrix coefficients and solution variables defined on original computational mesh, and a newly proposed mapping using all WF mesh (WF-all), on which matrix coefficients and solution variables are defined. Both the P-ADI and the P-SIP have been integrated into a two-dimensional (2D) hydrodynamic model, the CCHE2D (Center of Computational Hydroscience and Engineering) model, developed by the National Center for Computational Hydroscience and Engineering at the University of Mississippi. This study for the first time compared these two parallel solvers and their efficiency using examples and applications in complex geometries, which can provide valuable guidance for future uses of these two parallel implicit solvers in computational fluids dynamics (CFD). Both parallel solvers demonstrated higher efficiency than their serial counterparts on the CPU (Central Processing Unit): 3.73~4.98 speedup ratio for flow simulations, and 2.166~3.648 speedup ratio for sediment transport simulations. In general, the P-ADI solver is faster than but not as stable as the P-SIP solver; and for the P-SIP solver, the newly developed mapping method WF-all significantly improved the conventional mapping method WF-e.
- 25 April 2024
- Published by Elsevier in Advances in Water Resources
- Vol. 188
Application of 1D model for overland flow simulations on 2D complex domains
- 25 April 2024
- Published by Elsevier in Advances in Water Resources
- Vol. 188
Application of 1D model for overland flow simulations on 2D complex domains
- Open Access
- 10 January 2024
- Published by IntechOpen
Erosion Control at Downstream of Reservoir Using In-stream Weirs
As low-head hydraulic structures, instream weirs are built across rivers to control the upstream water surface elevation and the downstream flow conditions. This chapter presents a study of erosion control using instream weirs at downstream of a reservoir; JiJi Weir was built across the longest river in Taiwan, Chuoshui Creek, a mountainous river with steep slopes. Due to the easy-to-be-eroded fine lithology layers of mud, shiver, and sandstones on channel bed, the downstream of JiJi Weir had suffered from severe channel incision and head-cut development problems, which greatly threatens the integrity of the dam. To protect the JiJi Weir and its downstream channel from serious channel erosions, the Water Resources Agency (WRA) of Taiwan proposed erosion control plans that multiple instream weir structures were to be installed along the downstream channel of JiJi Weir. A three-dimensional (3D) numerical model, CCHE3D model with capabilities of simulating bedrock erosions, was used to evaluate those erosion control plans and thus explore for the optimal design.
- 10 January 2024
- Published by IntechOpen
Open AccessErosion Control at Downstream of Reservoir Using In-stream Weirs
As low-head hydraulic structures, instream weirs are built across rivers to control the upstream water surface elevation and the downstream flow conditions. This chapter presents a study of erosion control using instream weirs at downstream of a reservoir; JiJi Weir was built across the longest river in Taiwan, Chuoshui Creek, a mountainous river with steep slopes. Due to the easy-to-be-eroded fine lithology layers of mud, shiver, and sandstones on channel bed, the downstream of JiJi Weir had suffered from severe channel incision and head-cut development problems, which greatly threatens the integrity of the dam. To protect the JiJi Weir and its downstream channel from serious channel erosions, the Water Resources Agency (WRA) of Taiwan proposed erosion control plans that multiple instream weir structures were to be installed along the downstream channel of JiJi Weir. A three-dimensional (3D) numerical model, CCHE3D model with capabilities of simulating bedrock erosions, was used to evaluate those erosion control plans and thus explore for the optimal design.
- 8 December 2023
- Published by Elsevier in Journal of Hydrology
- Vol. 628
Generation of 1D channel networks for overland flow simulations on 2D complex domains
- 8 December 2023
- Published by Elsevier in Journal of Hydrology
- Vol. 628
Generation of 1D channel networks for overland flow simulations on 2D complex domains
- Open Access
- 14 April 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (8) , 4940
Development of a Two-Dimensional Hybrid Sediment-Transport Model
This paper presents the development of a two-dimensional hydrodynamic sediment transport model using the finite volume method based on a collocated unstructured hybrid-mesh system consisting of triangular and quadrilateral cells. The model is a single-phase nonequilibrium sediment-transport model for nonuniform and noncohesive sediments in unsteady turbulent flows that considers multiple sediment-transport processes such as deposition, erosion, transport, and bed sorting. This model features a hybrid unstructured mesh system for easy mesh generation in complex domains. To avoid interpolation from vertices in conventional unstructured models, this model adopted a second-order accurate edge-gradient evaluation method to consider the mesh irregularities based on Taylor’s series expansion. In addition, the multipoint momentum interpolation corrections were integrated to avoid possible nonphysical oscillations during the wetting-and-drying process, common in unsteady sediment transport problems, to ensure both numerical stability and numerical accuracy. The developed sediment transport model was validated by a benchmark degradation case for the erosion process with armoring effects, a benchmark aggradation case for the deposition process, and a naturally meandering river for long-term unsteady sediment-transport processes. Finally, the model was successfully applied to simulate sediment transport in a reservoir that was significantly affected by typhoon events.
- 14 April 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (8) , 4940
Open AccessDevelopment of a Two-Dimensional Hybrid Sediment-Transport Model
This paper presents the development of a two-dimensional hydrodynamic sediment transport model using the finite volume method based on a collocated unstructured hybrid-mesh system consisting of triangular and quadrilateral cells. The model is a single-phase nonequilibrium sediment-transport model for nonuniform and noncohesive sediments in unsteady turbulent flows that considers multiple sediment-transport processes such as deposition, erosion, transport, and bed sorting. This model features a hybrid unstructured mesh system for easy mesh generation in complex domains. To avoid interpolation from vertices in conventional unstructured models, this model adopted a second-order accurate edge-gradient evaluation method to consider the mesh irregularities based on Taylor’s series expansion. In addition, the multipoint momentum interpolation corrections were integrated to avoid possible nonphysical oscillations during the wetting-and-drying process, common in unsteady sediment transport problems, to ensure both numerical stability and numerical accuracy. The developed sediment transport model was validated by a benchmark degradation case for the erosion process with armoring effects, a benchmark aggradation case for the deposition process, and a naturally meandering river for long-term unsteady sediment-transport processes. Finally, the model was successfully applied to simulate sediment transport in a reservoir that was significantly affected by typhoon events.
- 22 March 2023
- Published by Elsevier in Journal of Hydrology
- Vol. 620
Physically based numerical model for the landscape evolution of soil-mantled watersheds driven by rainfall and overland flow
- 22 March 2023
- Published by Elsevier in Journal of Hydrology
- Vol. 620
Physically based numerical model for the landscape evolution of soil-mantled watersheds driven by rainfall and overland flow
- 7 October 2022
- Published by Morressier GmbH
Automatic Structured Mesh Generation
An automatic generation algorithm, Advancing Extraction Method (AEM), for body-fitted structured meshes is presented. The proposed method is desi |
- 7 October 2022
- Published by Morressier GmbH
Automatic Structured Mesh Generation
An automatic generation algorithm, Advancing Extraction Method (AEM), for body-fitted structured meshes is presented. The proposed method is desi |