Syed Ahmed Ali
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Syed Ahmed Ali has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Mohammad Mozahar Hossain
Department of Chemical Engineering, King Fahd University of Petroleum and Minerals, Dhahran, Saudi Arabia
7 shared publications - Abdullah Mohammed Aitani
Interdisciplinary Research Center for Refining and Advanced Chemicals, King Fahd University of Petroleum & Minerals, Dhahran, Saudi Arabia
3 shared publications - Faisal M. Almulla
School of Chemical Engineering and Analytical Science, The University of Manchester, Manchester M13 9PL, United Kingdom
3 shared publications - Wasim Ullah Khan
National Research and Development Institute for Cryogenic and Isotopic Technologies, 240050 Ramnicu Valcea, Romania
3 shared publications - Dwi Hantoko
Institute of Energy and Power Engineering, Zhejiang University of Technology, Hangzhou, China
2 shared publications Essa I. Alnaimi
2 shared publications
Latest Publications
- 24 September 2026
- Published by Elsevier in Chemical Engineering Science
- Vol. 339
Kinetics-driven reactor design for NH3 decomposition to hydrogen over nickel and cobalt catalysts
- 24 September 2026
- Published by Elsevier in Chemical Engineering Science
- Vol. 339
Kinetics-driven reactor design for NH3 decomposition to hydrogen over nickel and cobalt catalysts
- 15 February 2025
- Published by Elsevier in Chemical Engineering Research and Design
- Vol. 215, 494-506
Hierarchical zeolite-containing mesoporous silica core-shell (Beta@MS) catalysts for the conversion of heavy reformate to xylenes
- 15 February 2025
- Published by Elsevier in Chemical Engineering Research and Design
- Vol. 215, 494-506
Hierarchical zeolite-containing mesoporous silica core-shell (Beta@MS) catalysts for the conversion of heavy reformate to xylenes
- 5 February 2025
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 64 (7) , 3614-3634
Production of Xylenes from Heavy Reformate: Advances in Process Chemistry, Catalyst Design, and Kinetics
- 5 February 2025
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 64 (7) , 3614-3634
Production of Xylenes from Heavy Reformate: Advances in Process Chemistry, Catalyst Design, and Kinetics
- 3 June 2024
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 63 (23) , 10126-10139
Molecular-Level Kinetic Modeling of Catalytic Naphtha Reforming
- 3 June 2024
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 63 (23) , 10126-10139
Molecular-Level Kinetic Modeling of Catalytic Naphtha Reforming
- 1 April 2024
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 63 (14) , 5987-6002
n-Butane Oxidation to Maleic Anhydride: Reaction Mechanism and Kinetics Over VPO Catalyst
- 1 April 2024
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 63 (14) , 5987-6002
n-Butane Oxidation to Maleic Anhydride: Reaction Mechanism and Kinetics Over VPO Catalyst
- 13 February 2024
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 9 (6) , 1433-1443
Influence of feed contamination on the conversion of heavy reformate and toluene over a composite hierarchical zeolite catalyst
The effect of feed contaminants on the conversion of heavy reformate and toluene mixture over a catalyst containing 4 wt% Mo impregnated on a bifunctional hierarchical composite of mordenite and ZSM-5 is reported. Specifically, the effects of contaminants in the feed (water, 1,2,4,5-tetramethylbenzene (1245-TeMB) and indene) and contaminants in hydrogen (H2S and CO) were investigated through catalytic performance tests in a fixed-bed micro-reactor at 350 °C and 20 bar H2. The presence of >35 ppm water in the feed caused significant reduction in the dealkylation of methylethylbenzenes (MEBs) due to a decrease in catalyst's acidity. Hence a dried feed (containing 35 ppm water) was used. An increase of 1.2 wt% in the formation of xylenes was observed with the introduction of 10 wt% 1245-TeMB in the feed due to an increase in the methyl/ring ratio. The addition of 1 wt% indene in the feed resulted in a 4 wt% drop in the formation of xylenes due to the preferential adsorption of indene. The tests with 50 ppm H2S and 50 ppm CO in hydrogen showed a drop of about 2 wt% in the formation of xylenes. However, the weak basicity of CO exhibited a much lower impact than the adsorption of H2S on the dealkylation. The effects of these contaminants are discussed in the light of changes observed in product composition during the introduction of a contaminant (48 h) and after restoring the baseline conditions (48 h).
- 13 February 2024
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 9 (6) , 1433-1443
Influence of feed contamination on the conversion of heavy reformate and toluene over a composite hierarchical zeolite catalyst
The effect of feed contaminants on the conversion of heavy reformate and toluene mixture over a catalyst containing 4 wt% Mo impregnated on a bifunctional hierarchical composite of mordenite and ZSM-5 is reported. Specifically, the effects of contaminants in the feed (water, 1,2,4,5-tetramethylbenzene (1245-TeMB) and indene) and contaminants in hydrogen (H2S and CO) were investigated through catalytic performance tests in a fixed-bed micro-reactor at 350 °C and 20 bar H2. The presence of >35 ppm water in the feed caused significant reduction in the dealkylation of methylethylbenzenes (MEBs) due to a decrease in catalyst's acidity. Hence a dried feed (containing 35 ppm water) was used. An increase of 1.2 wt% in the formation of xylenes was observed with the introduction of 10 wt% 1245-TeMB in the feed due to an increase in the methyl/ring ratio. The addition of 1 wt% indene in the feed resulted in a 4 wt% drop in the formation of xylenes due to the preferential adsorption of indene. The tests with 50 ppm H2S and 50 ppm CO in hydrogen showed a drop of about 2 wt% in the formation of xylenes. However, the weak basicity of CO exhibited a much lower impact than the adsorption of H2S on the dealkylation. The effects of these contaminants are discussed in the light of changes observed in product composition during the introduction of a contaminant (48 h) and after restoring the baseline conditions (48 h).
- Open Access
Kinetics of Heavy Reformate Conversion to Xylenes over MCM-41 on Zeolite Beta Composite Catalyst
Commercial heavy reformate is converted over MCM-41 on zeolite beta composite catalyst to produce mixed xylenes in a fluidized-bed batch reactor. The heavy reformate feedstock contains 67.4 wt.% trimethyl benzenes (TMBs) and 31.1 wt.% methyl ethyl benzenes (MEBs). The experiments were carried out at 300, 350 and 400 °C, while the reaction times were varied between 5 and 20 s. The conversion of MEBs was more than two times the conversion of TMBs. The selectivity to xylenes was quite high (60–65 wt.%) but changed very little with reaction time or temperature. A kinetic model was developed using a five-reaction network. The product composition obtained from the estimated kinetic parameters closely matches the experimental results, which confirms the validity of the assumptions made for kinetic modeling. The trend in the apparent activation energies of the reactions was in accordance with the relative size of the reactant molecules, and the lowest activation energy was for the transalkylation of TMBs with toluene to produce xylenes.
Open AccessKinetics of Heavy Reformate Conversion to Xylenes over MCM-41 on Zeolite Beta Composite Catalyst
Commercial heavy reformate is converted over MCM-41 on zeolite beta composite catalyst to produce mixed xylenes in a fluidized-bed batch reactor. The heavy reformate feedstock contains 67.4 wt.% trimethyl benzenes (TMBs) and 31.1 wt.% methyl ethyl benzenes (MEBs). The experiments were carried out at 300, 350 and 400 °C, while the reaction times were varied between 5 and 20 s. The conversion of MEBs was more than two times the conversion of TMBs. The selectivity to xylenes was quite high (60–65 wt.%) but changed very little with reaction time or temperature. A kinetic model was developed using a five-reaction network. The product composition obtained from the estimated kinetic parameters closely matches the experimental results, which confirms the validity of the assumptions made for kinetic modeling. The trend in the apparent activation energies of the reactions was in accordance with the relative size of the reactant molecules, and the lowest activation energy was for the transalkylation of TMBs with toluene to produce xylenes.
- Open Access
Experimental Investigation of Metal-Based Calixarenes as Dispersed Catalyst Precursors for Heavy Oil Hydrocracking
Slurry-phase hydrocracking utilizing metal-containing oil-soluble compounds as precursors of dispersed catalysts is an effective approach for heavy oil upgrading. We propose applying metal-based p-tert-butylcalix[6]arene (TBC[6]s) organic species as dispersed catalyst precursors to enhance catalytic hydrogenation reactions involved in the upgrading of vacuum gas oil (VGO). Co- and Ni-based TBC[6]s were synthesized and characterized by SEM-EDX, ICP, XRD, and FT-IR. The thermogravimetric and calorimetric behaviors of the synthesized complexes, which are key properties of dispersed hydrocracking catalysts, were also explored. The experimental evaluation of the synthesized catalyst precursors show that the synthesized metal-based TBC[6] catalyst precursors improved the catalytic hydrogenation reactions. A co-catalytic system was also investigated by adding a commercial, first-stage hydrocracking supported catalyst in addition to the dispersed catalysts. The naphtha yields increased from 10.7 wt.% for the supported catalyst to 11.7 wt.% and 12 wt.% after adding it along with Ni-TBC[6] and Co-TBC[6], respectively. Mixing the metal-based precursors resulted in elevated yields of liquid products due to the in situ generation of highly active Co–Ni bimetallic dispersed catalysts.
Open AccessExperimental Investigation of Metal-Based Calixarenes as Dispersed Catalyst Precursors for Heavy Oil Hydrocracking
Slurry-phase hydrocracking utilizing metal-containing oil-soluble compounds as precursors of dispersed catalysts is an effective approach for heavy oil upgrading. We propose applying metal-based p-tert-butylcalix[6]arene (TBC[6]s) organic species as dispersed catalyst precursors to enhance catalytic hydrogenation reactions involved in the upgrading of vacuum gas oil (VGO). Co- and Ni-based TBC[6]s were synthesized and characterized by SEM-EDX, ICP, XRD, and FT-IR. The thermogravimetric and calorimetric behaviors of the synthesized complexes, which are key properties of dispersed hydrocracking catalysts, were also explored. The experimental evaluation of the synthesized catalyst precursors show that the synthesized metal-based TBC[6] catalyst precursors improved the catalytic hydrogenation reactions. A co-catalytic system was also investigated by adding a commercial, first-stage hydrocracking supported catalyst in addition to the dispersed catalysts. The naphtha yields increased from 10.7 wt.% for the supported catalyst to 11.7 wt.% and 12 wt.% after adding it along with Ni-TBC[6] and Co-TBC[6], respectively. Mixing the metal-based precursors resulted in elevated yields of liquid products due to the in situ generation of highly active Co–Ni bimetallic dispersed catalysts.