Sarah-Jane Potts
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sarah-Jane Potts has a total of 61 co-authors. Here are the top co-authors by number of shared publications:
- Trystan Watson
Swansea University, Bay Campus, Neath, Skewen SA18EN, Wales
7 shared publications - Carys Worsley
Swansea University, Bay Campus, Neath, Skewen SA18EN, Wales
6 shared publications - Eifion Jewell
SPECIFIC Faculty of Science and Engineering Swansea University Bay Campus, Crymlyn Burrows Swansea SA1 8EN UK
6 shared publications - Chris Phillips
Welsh Centre for Printing and Coating, College of Engineering, Swansea University, Swansea, UK
5 shared publications - Tim Charles Claypole
Swansea University
5 shared publications Eifion Jewell
3 shared publications
Latest Publications
- Open Access
- 17 April 2026
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 303
Outdoor evaluation of carbon-based perovskite solar modules: Comparison between temperate and tropical climates
- 17 April 2026
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 303
Open AccessOutdoor evaluation of carbon-based perovskite solar modules: Comparison between temperate and tropical climates
- Open Access
- 24 November 2025
- Published by Springer Nature in Communications Materials
- Vol. 6 (1) , 266
Manufacturing planar perovskite solar cells in dusty environments
Production of silicon solar cells necessitates cleanrooms to prevent dust contamination, which can lead to defects and reduced performance. This poses challenges for scaling up manufacturing and improving accessibility for device manufacture in less developed economies as cleanrooms represent an expensive and energy intensive investment, and so it is key that the next generation of solar technology differentiates from this. Perovskite has the potential to be far more robust and resilient to defects caused by dust particles, which then impacts on the capital cost of the equipment required for manufacture. This study evaluates the effects of non-conductive dust on planar perovskite devices, testing two different device structures with efficiencies exceeding 16%, testing an active area of 0.09 cm 2 . The setup simulated dust settling during the manufacturing process, expecting compromised performance in contaminated devices. Results revealed that devices with dust performed similarly to clean ones, with only limited losses in some performance metrics. High tolerance to contamination suggests that perovskite technology may remain operational under less controlled environments. These findings point toward a more accessible fabrication route reducing dependence on expensive cleanroom conditions typically required for silicon-based technologies.
- 24 November 2025
- Published by Springer Nature in Communications Materials
- Vol. 6 (1) , 266
Open AccessManufacturing planar perovskite solar cells in dusty environments
Production of silicon solar cells necessitates cleanrooms to prevent dust contamination, which can lead to defects and reduced performance. This poses challenges for scaling up manufacturing and improving accessibility for device manufacture in less developed economies as cleanrooms represent an expensive and energy intensive investment, and so it is key that the next generation of solar technology differentiates from this. Perovskite has the potential to be far more robust and resilient to defects caused by dust particles, which then impacts on the capital cost of the equipment required for manufacture. This study evaluates the effects of non-conductive dust on planar perovskite devices, testing two different device structures with efficiencies exceeding 16%, testing an active area of 0.09 cm 2 . The setup simulated dust settling during the manufacturing process, expecting compromised performance in contaminated devices. Results revealed that devices with dust performed similarly to clean ones, with only limited losses in some performance metrics. High tolerance to contamination suggests that perovskite technology may remain operational under less controlled environments. These findings point toward a more accessible fabrication route reducing dependence on expensive cleanroom conditions typically required for silicon-based technologies.
- Open Access
- 30 September 2025
- Published by Wiley in Advanced Materials Technologies
- Vol. 11 (2)
Outdoor Stability of 518 cm 2 Active Area Screen‐Printed Mesoscopic Carbon‐Based Perovskite Solar Modules Over 12 Months
Mesoscopic carbon‐based perovskite solar cells (C‐PSCs) composed of screen‐printed TiO 2 , ZrO 2 , and carbon layers offer a pathway to stable, scalable, low‐cost photovoltaics via commercially mature fabrication methods. While their potential lifespan has been demonstrated under standardized conditions, few studies examine the behavior of large‐area modules exposed to real‐world environments. Here, 12 months of outdoor weathering data are presented for 518 cm 2 active area MAPbI 3 modules with over 80% geometric fill factor, fabricated using low‐cost mechanical scribing. Modules exhibited power conversion efficiencies (PCEs) up to 9.4% under 1 sun, with PCE increasing at lower light intensities. Following outdoor continuous intermittent power point tracking for over 12 months, an encapsulated module retained 68% of its initial PCE. Performance remained stable during cooler months, only falling when temperatures rose during summer months. Similar temperature‐dependent trends are observed in repeated trials. Weathering trials identified key degradation pathways linked to fabrication—namely, non‐uniform heating during perovskite annealing, encapsulation, and infiltration‐related failures. Controlling heat exposure and conformity during module manufacture and operation is therefore critical to extending lifetime. These results highlight the importance of real‐condition assessments in optimizing the scale‐up of novel perovskite technologies, providing key insights into the steps required to achieve commercially viable lifetimes.
- 30 September 2025
- Published by Wiley in Advanced Materials Technologies
- Vol. 11 (2)
Open AccessOutdoor Stability of 518 cm 2 Active Area Screen‐Printed Mesoscopic Carbon‐Based Perovskite Solar Modules Over 12 Months
Mesoscopic carbon‐based perovskite solar cells (C‐PSCs) composed of screen‐printed TiO 2 , ZrO 2 , and carbon layers offer a pathway to stable, scalable, low‐cost photovoltaics via commercially mature fabrication methods. While their potential lifespan has been demonstrated under standardized conditions, few studies examine the behavior of large‐area modules exposed to real‐world environments. Here, 12 months of outdoor weathering data are presented for 518 cm 2 active area MAPbI 3 modules with over 80% geometric fill factor, fabricated using low‐cost mechanical scribing. Modules exhibited power conversion efficiencies (PCEs) up to 9.4% under 1 sun, with PCE increasing at lower light intensities. Following outdoor continuous intermittent power point tracking for over 12 months, an encapsulated module retained 68% of its initial PCE. Performance remained stable during cooler months, only falling when temperatures rose during summer months. Similar temperature‐dependent trends are observed in repeated trials. Weathering trials identified key degradation pathways linked to fabrication—namely, non‐uniform heating during perovskite annealing, encapsulation, and infiltration‐related failures. Controlling heat exposure and conformity during module manufacture and operation is therefore critical to extending lifetime. These results highlight the importance of real‐condition assessments in optimizing the scale‐up of novel perovskite technologies, providing key insights into the steps required to achieve commercially viable lifetimes.
- Open Access
- 24 May 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 12 (25) , 9401-9411
Infiltration issues in printed mesoporous carbon perovskite solar cells: a troubleshooting guide
Characteristic CPSC infiltration defects are identified and linked to specific manufacturing issues. Preventative solutions are presented, to produce a troubleshooting reference resource for tackling poor infiltration at multiple scales.
- 24 May 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 12 (25) , 9401-9411
Open AccessInfiltration issues in printed mesoporous carbon perovskite solar cells: a troubleshooting guide
Characteristic CPSC infiltration defects are identified and linked to specific manufacturing issues. Preventative solutions are presented, to produce a troubleshooting reference resource for tackling poor infiltration at multiple scales.
- Open Access
- 9 April 2024
- Published by Wiley in Advanced Functional Materials
- Vol. 34 (36) , 2401959
Enhancing the Performance of the Mesoporous TiO2 Film in Printed Perovskite Photovoltaics through High‐Speed Imaging and Ink Rheology Techniques
Mesoscopic carbon‐based perovskite solar cells (C‐PSCs) have the potential to be manufactured at an industrial scale by utilizing screen‐printing, a simple, affordable, and commercially mature process. As such, many recent publications have focused on enhancing performance through modifying cell architecture and perovskite chemistries. This work examines how ink rheology can be tuned to optimize cell performance through reducing the occurrence of common print defects to create higher quality m‐TiO2 films. Inks with different solvent dilutions and rheological profiles are assessed using high‐speed imaging through the screen‐printing visualization (SPV) technique, to investigate the impact of the viscosity and elasticity on ink separation mechanisms. The resultant film quality and its influence on device performances are then assessed. Ink separation lengths are minimized, and the formation of filaments ceases during printing, leading to improved TiO2 film topography and homogenous infiltration of the perovskite precursor. Consequently, PCE is improved by over 10% of the original efficiency in cells and 224 cm2 active area modules due to enhanced Voc and FF. These results not only provide key insights into tailoring ink rheology, to achieve improved print homogeneity and higher performing cells, but also aid further work on enhancing the performance of other screen‐printed functional films.
- 9 April 2024
- Published by Wiley in Advanced Functional Materials
- Vol. 34 (36) , 2401959
Open AccessEnhancing the Performance of the Mesoporous TiO2 Film in Printed Perovskite Photovoltaics through High‐Speed Imaging and Ink Rheology Techniques
Mesoscopic carbon‐based perovskite solar cells (C‐PSCs) have the potential to be manufactured at an industrial scale by utilizing screen‐printing, a simple, affordable, and commercially mature process. As such, many recent publications have focused on enhancing performance through modifying cell architecture and perovskite chemistries. This work examines how ink rheology can be tuned to optimize cell performance through reducing the occurrence of common print defects to create higher quality m‐TiO2 films. Inks with different solvent dilutions and rheological profiles are assessed using high‐speed imaging through the screen‐printing visualization (SPV) technique, to investigate the impact of the viscosity and elasticity on ink separation mechanisms. The resultant film quality and its influence on device performances are then assessed. Ink separation lengths are minimized, and the formation of filaments ceases during printing, leading to improved TiO2 film topography and homogenous infiltration of the perovskite precursor. Consequently, PCE is improved by over 10% of the original efficiency in cells and 224 cm2 active area modules due to enhanced Voc and FF. These results not only provide key insights into tailoring ink rheology, to achieve improved print homogeneity and higher performing cells, but also aid further work on enhancing the performance of other screen‐printed functional films.
- Open Access
- 3 April 2024
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 5 (10) , 4354-4365
Age-induced excellence with green solvents: the impact of residual solvent and post-treatments in screen-printed carbon perovskite solar cells and modules
Screen-printed perovskite devices made using green γ-valerolactone precursors are found to improve significantly following fabrication due to slow residual solvent loss over time. This is also observed in large-scale 220 cm2 modules.
- 3 April 2024
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 5 (10) , 4354-4365
Open AccessAge-induced excellence with green solvents: the impact of residual solvent and post-treatments in screen-printed carbon perovskite solar cells and modules
Screen-printed perovskite devices made using green γ-valerolactone precursors are found to improve significantly following fabrication due to slow residual solvent loss over time. This is also observed in large-scale 220 cm2 modules.
- Open Access
Improving the Corrosion Performance of Organically Coated Steel Using a Sol–Gel Overcoat
Organically coated steels are widely used in applications in which they are subjected to the natural environment and therefore require excellent corrosion resistance. Organic clearcoats are typically employed as a barrier that improves the overall corrosion resistance; however, they are typically derived from fossil fuel-based feedstock. A more sustainable alternative could be possible using sol–gel coatings. The application of a simple tetraethoxysilane (TEOS)-based sol–gel was applied to polyurethane-coated steels using a spray coater. The concentration of TEOS was altered to produce coatings containing either 2.5% or 10%. The 10% TEOS resulted in dense, homogeneous coatings that offered a significant improvement in corrosion resistance compared to an uncoated substrate. Whereas the 2.5% TEOS coatings were inhomogeneous and porous, which indicated a limitation of concentration required to produce a uniform coating. The successful demonstration of using a simple TEOS-based coating to improve the corrosion resistance of organically coated steel highlights the potential for further investigation into the use of sol–gels for these applications.
Open AccessImproving the Corrosion Performance of Organically Coated Steel Using a Sol–Gel Overcoat
Organically coated steels are widely used in applications in which they are subjected to the natural environment and therefore require excellent corrosion resistance. Organic clearcoats are typically employed as a barrier that improves the overall corrosion resistance; however, they are typically derived from fossil fuel-based feedstock. A more sustainable alternative could be possible using sol–gel coatings. The application of a simple tetraethoxysilane (TEOS)-based sol–gel was applied to polyurethane-coated steels using a spray coater. The concentration of TEOS was altered to produce coatings containing either 2.5% or 10%. The 10% TEOS resulted in dense, homogeneous coatings that offered a significant improvement in corrosion resistance compared to an uncoated substrate. Whereas the 2.5% TEOS coatings were inhomogeneous and porous, which indicated a limitation of concentration required to produce a uniform coating. The successful demonstration of using a simple TEOS-based coating to improve the corrosion resistance of organically coated steel highlights the potential for further investigation into the use of sol–gels for these applications.
- Open Access
- 3 January 2022
- Published by Springer Nature in Journal of Materials Science
- Vol. 57 (4) , 2650-2666
The influence of carbon morphologies and concentrations on the rheology and electrical performance of screen-printed carbon pastes
Screen-printing inks containing various morphologies of carbon are used in the production of a variety of printed electronics applications. Particle morphology influences the rheology of the ink which will affect the deposition and therefore the electrical performance of a printed component. To assess the effect of both carbon morphology and concentration on print topography and conductivity, screen printable carbon inks with differing loading concentrations of graphite, carbon black and graphite nanoplatelets (GNPs) were formulated, printed and characterised, with rheological and novel print visualisation techniques used to elucidate the mechanisms responsible. Carbon morphology had significant effects on the packing of particles. The smaller carbon black particles had more interparticle interactions leading to better conductivities, but also higher ink viscosities and elasticities than the other morphologies. Increases in carbon concentration led to increases in film thickness and roughness for all morphologies. However, beyond a critical point further increases in carbon concentration led to agglomerations of particles, mesh marking and increases in surface roughness, preventing further improvements in the print conductivity. The optimal loading concentrations were identifiable using a custom-made screen-printing apparatus used with high speed imaging for all morphologies. Notable increases in filamentation during ink separation were found to occur with further increases in carbon concentration beyond the optimum. As this point could not be identified using shear rheology alone, this method combined with shear rheology could be used to optimise the carbon concentration of screen-printing inks, preventing the use of excess material which has no benefit on print quality and conductivity.
- 3 January 2022
- Published by Springer Nature in Journal of Materials Science
- Vol. 57 (4) , 2650-2666
Open AccessThe influence of carbon morphologies and concentrations on the rheology and electrical performance of screen-printed carbon pastes
Screen-printing inks containing various morphologies of carbon are used in the production of a variety of printed electronics applications. Particle morphology influences the rheology of the ink which will affect the deposition and therefore the electrical performance of a printed component. To assess the effect of both carbon morphology and concentration on print topography and conductivity, screen printable carbon inks with differing loading concentrations of graphite, carbon black and graphite nanoplatelets (GNPs) were formulated, printed and characterised, with rheological and novel print visualisation techniques used to elucidate the mechanisms responsible. Carbon morphology had significant effects on the packing of particles. The smaller carbon black particles had more interparticle interactions leading to better conductivities, but also higher ink viscosities and elasticities than the other morphologies. Increases in carbon concentration led to increases in film thickness and roughness for all morphologies. However, beyond a critical point further increases in carbon concentration led to agglomerations of particles, mesh marking and increases in surface roughness, preventing further improvements in the print conductivity. The optimal loading concentrations were identifiable using a custom-made screen-printing apparatus used with high speed imaging for all morphologies. Notable increases in filamentation during ink separation were found to occur with further increases in carbon concentration beyond the optimum. As this point could not be identified using shear rheology alone, this method combined with shear rheology could be used to optimise the carbon concentration of screen-printing inks, preventing the use of excess material which has no benefit on print quality and conductivity.
- Open Access
- 30 November 2021
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 3 (2) , 1125-1138
Green solvent engineering for enhanced performance and reproducibility in printed carbon-based mesoscopic perovskite solar cells and modules
Green solvent mixes are applied in printed mesoscopic perovskite solar cells and modules, achieving 13.8% PCE at 1 cm 2 and >9% PCE in a 220 cm 2 module. This shows how green solvent engineering can aid improvement and scale-up in emerging technologies.
- 30 November 2021
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 3 (2) , 1125-1138
Open AccessGreen solvent engineering for enhanced performance and reproducibility in printed carbon-based mesoscopic perovskite solar cells and modules
Green solvent mixes are applied in printed mesoscopic perovskite solar cells and modules, achieving 13.8% PCE at 1 cm 2 and >9% PCE in a 220 cm 2 module. This shows how green solvent engineering can aid improvement and scale-up in emerging technologies.
- 26 October 2021
- Published by Swansea University
Advanced Manufacture by Screen Printing
Screen-printing is the most widely used process in printed electronics, due to its ability to transfer materials with a wide range of functional properties at high thickness and solid loading. However, the science of screen printing is still rooted in the graphics era, with limited understanding of the fundamental science behind the ink transfer process. A multifaceted approach encompassing all aspects of the production of printed electronics from ink formulation, through screen-printing and post processing was therefore undertaken. With a focus on carbon inks due to their electrical conductivity, low cost, inertness and ability to be modified or functionalised. Parametric studies found that with blade squeegees, lower angles and softer blades led to increases in ink deposition, irrespective of ink rheology. However, the effects of print speed and snap distance were related to the rheology of the inks. Existing computational models were inaccurate and based on two contrasting theories. Extensional CaBER testing provided qualitative indications of the effect of separation speed and distance on deposition. However, this could only assess the effect of vertical, 2-dimensional forces and could not evaluate the influence of shear forces due to separation angle or the effects of the screen mesh. For this purpose, a screen-printing visualisation rig was specifically constructed, allowing the ink transfer mechanism to be captured for the first time. This identified similarities with one of the two theories, although existing models had oversimplified the process and did not account for variations in lengths of the separation regions or the contact angle between the mesh and substrate. It was also found that changes in the ink rheology and parameter settings changes the lengths of these regions, as well as the shape and presence of filaments formed during separation. The parameters of print speed, snap distance, solid loading and ink rheology were assessed and found to affect the mesh/substrate contact time and filamentation behaviour. This had a quantifiable effect on ink deposition, in terms of the amount of ink transfer, roughness and therefore conductivity. Finally, photonic annealing and subsequent compression rolling were found to enhance the conductivity of carbon inks by removing binder between particles and consolidating the ink film, leading to 8 times reduction in resistivity for a graphite-based ink and halving in resistivity for an ink containing a combination of carbon black and graphite, where there was less potential for improvement due to the conductive bridges between the graphite flakes.
- 26 October 2021
- Published by Swansea University
Advanced Manufacture by Screen Printing
Screen-printing is the most widely used process in printed electronics, due to its ability to transfer materials with a wide range of functional properties at high thickness and solid loading. However, the science of screen printing is still rooted in the graphics era, with limited understanding of the fundamental science behind the ink transfer process. A multifaceted approach encompassing all aspects of the production of printed electronics from ink formulation, through screen-printing and post processing was therefore undertaken. With a focus on carbon inks due to their electrical conductivity, low cost, inertness and ability to be modified or functionalised. Parametric studies found that with blade squeegees, lower angles and softer blades led to increases in ink deposition, irrespective of ink rheology. However, the effects of print speed and snap distance were related to the rheology of the inks. Existing computational models were inaccurate and based on two contrasting theories. Extensional CaBER testing provided qualitative indications of the effect of separation speed and distance on deposition. However, this could only assess the effect of vertical, 2-dimensional forces and could not evaluate the influence of shear forces due to separation angle or the effects of the screen mesh. For this purpose, a screen-printing visualisation rig was specifically constructed, allowing the ink transfer mechanism to be captured for the first time. This identified similarities with one of the two theories, although existing models had oversimplified the process and did not account for variations in lengths of the separation regions or the contact angle between the mesh and substrate. It was also found that changes in the ink rheology and parameter settings changes the lengths of these regions, as well as the shape and presence of filaments formed during separation. The parameters of print speed, snap distance, solid loading and ink rheology were assessed and found to affect the mesh/substrate contact time and filamentation behaviour. This had a quantifiable effect on ink deposition, in terms of the amount of ink transfer, roughness and therefore conductivity. Finally, photonic annealing and subsequent compression rolling were found to enhance the conductivity of carbon inks by removing binder between particles and consolidating the ink film, leading to 8 times reduction in resistivity for a graphite-based ink and halving in resistivity for an ink containing a combination of carbon black and graphite, where there was less potential for improvement due to the conductive bridges between the graphite flakes.