Behzad Nayebi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Behzad Nayebi has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
- Mehdi Shahedi Asl
Advanced Materials Research Center, Department of Chemistry and Materials Science, School of Science, Xi’an Jiaotong-Liverpool University, Suzhou, China
26 shared publications Mahdi Ghassemi Kakroudi
9 shared publicationsMohammadreza Shokouhimehr
9 shared publicationsZohre Ahmadi
9 shared publications- Mohammadreza Shokouhimehr
Institute of Nanosensor Technology, Hanyang University, Ansan, Republic of Korea
6 shared publications Soroush Parvizi
5 shared publications
Latest Publications
- Open Access
- 1 March 2025
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 13 (3) , 1325-1340
Spark plasma sintering of a novel Mg-0.7Ca alloy: A comprehensive study
- 1 March 2025
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 13 (3) , 1325-1340
Open AccessSpark plasma sintering of a novel Mg-0.7Ca alloy: A comprehensive study
- Open Access
- 14 August 2024
- Published by Synsint Research Group in Synthesis and Sintering
- Vol. 4 (3) , 197-202
A perspective to efficient synthesis of zirconium carbide via novel pyro-vacuum method: lower temperatures and enhanced purity
The use of ultra-high temperature ceramics (UHTCs) as a novel additive in the refractory industry is becoming increasingly popular. However, the synthesis of such materials is associated with some commercial obstacles, mainly high-temperature synthesis methods. In the present study, the pyro-vacuum method is presented as a new method to decrease the final product's synthesis temperature and oxygen content. Some thermodynamic aspects and phase evolution of the materials during the synthesis procedure are described for the synthesis of non-oxide material. Conclusively, it seems that by applying vacuum conditions, the final UHTC phases can be synthesized at significantly lower temperatures (>400 °C lower, for ZrC), if adequate powder mixtures are considered. Also due to phase analysis, it was found that the oxygen content of the final phase is lower than the conventional routes and other references. The process provides promising prospects for the economic synthesis of UHTCs.
- 14 August 2024
- Published by Synsint Research Group in Synthesis and Sintering
- Vol. 4 (3) , 197-202
Open AccessA perspective to efficient synthesis of zirconium carbide via novel pyro-vacuum method: lower temperatures and enhanced purity
The use of ultra-high temperature ceramics (UHTCs) as a novel additive in the refractory industry is becoming increasingly popular. However, the synthesis of such materials is associated with some commercial obstacles, mainly high-temperature synthesis methods. In the present study, the pyro-vacuum method is presented as a new method to decrease the final product's synthesis temperature and oxygen content. Some thermodynamic aspects and phase evolution of the materials during the synthesis procedure are described for the synthesis of non-oxide material. Conclusively, it seems that by applying vacuum conditions, the final UHTC phases can be synthesized at significantly lower temperatures (>400 °C lower, for ZrC), if adequate powder mixtures are considered. Also due to phase analysis, it was found that the oxygen content of the final phase is lower than the conventional routes and other references. The process provides promising prospects for the economic synthesis of UHTCs.
- Open Access
- 26 June 2024
- Published by Synsint Research Group in Synthesis and Sintering
- Vol. 4 (2) , 154-159
On the synthesis and sintering behavior of a novel Mg-Ca alloy, Part II: Spark plasma sintering
With the growing interest in lightweight materials, magnesium and its alloys have received substantial attention for replacing existing alloys. After investigating the mechanical alloying process of Mg-Ca alloys and determining the optimum parameters for milling in part I of this study, the current research aims to examine the second step: the sintering process. This study proposes the powder metallurgy method to process Mg-Ca alloy through the spark plasma sintering technique at 420 °C under an applied pressure of 38 MPa. Samples with different additives (starch or paraffin) were sintered for various dwell times (7 and 10 min) to determine the optimal mechanical and physical properties. To study the microstructure and phase composition of the sintered alloys, X-ray diffractometer (XRD), field scanning electron microscopy (FESEM), and X-ray energy dispersive spectroscopy (EDS) were utilized. Density measurement, compression test, and micro-hardness evaluation were also conducted for the physical and mechanical feathers analysis. The results indicated that samples with a dwell time of 10 min exhibited superior mechanical properties. Additionally, the starch-containing sample outperformed the paraffin-containing sample in both physical and mechanical properties.
- 26 June 2024
- Published by Synsint Research Group in Synthesis and Sintering
- Vol. 4 (2) , 154-159
Open AccessOn the synthesis and sintering behavior of a novel Mg-Ca alloy, Part II: Spark plasma sintering
With the growing interest in lightweight materials, magnesium and its alloys have received substantial attention for replacing existing alloys. After investigating the mechanical alloying process of Mg-Ca alloys and determining the optimum parameters for milling in part I of this study, the current research aims to examine the second step: the sintering process. This study proposes the powder metallurgy method to process Mg-Ca alloy through the spark plasma sintering technique at 420 °C under an applied pressure of 38 MPa. Samples with different additives (starch or paraffin) were sintered for various dwell times (7 and 10 min) to determine the optimal mechanical and physical properties. To study the microstructure and phase composition of the sintered alloys, X-ray diffractometer (XRD), field scanning electron microscopy (FESEM), and X-ray energy dispersive spectroscopy (EDS) were utilized. Density measurement, compression test, and micro-hardness evaluation were also conducted for the physical and mechanical feathers analysis. The results indicated that samples with a dwell time of 10 min exhibited superior mechanical properties. Additionally, the starch-containing sample outperformed the paraffin-containing sample in both physical and mechanical properties.
- Open Access
- 1 April 2023
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 11 (4) , 1276-1291
Enhanced oxidation and overheating resistance of the extruded Mg–Zn–Al–Mn magnesium alloy by Calcium addition
- 1 April 2023
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 11 (4) , 1276-1291
Open AccessEnhanced oxidation and overheating resistance of the extruded Mg–Zn–Al–Mn magnesium alloy by Calcium addition
- 27 November 2022
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 295
Characteristics of porous SS316L: Influences of the Sn additive on the interfacial phenomena during the pressureless sintering
- 27 November 2022
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 295
Characteristics of porous SS316L: Influences of the Sn additive on the interfacial phenomena during the pressureless sintering
- 7 August 2022
- Published by Elsevier in Surfaces and Interfaces
- Vol. 34
In-situ synthesized MgO-based ceramic coatings on a novel Mg–Ca material: Morphological response to the PEO electrolyte
- 7 August 2022
- Published by Elsevier in Surfaces and Interfaces
- Vol. 34
In-situ synthesized MgO-based ceramic coatings on a novel Mg–Ca material: Morphological response to the PEO electrolyte
- 1 September 2021
- Published by Elsevier in Intermetallics
- Vol. 136, 107261
Formation of Al–Al2O3 core–shell nanosphere chains during electron beam melting of γ-TiAl
- 1 September 2021
- Published by Elsevier in Intermetallics
- Vol. 136, 107261
Formation of Al–Al2O3 core–shell nanosphere chains during electron beam melting of γ-TiAl
- Open Access
- 1 March 2021
- Published by Elsevier in Journal of Science: Advanced Materials and Devices
- Vol. 6 (1) , 42-48
Toughening of ZrB2-based composites with in-situ synthesized ZrC from ZrO2 and graphite precursors
- 1 March 2021
- Published by Elsevier in Journal of Science: Advanced Materials and Devices
- Vol. 6 (1) , 42-48
Open AccessToughening of ZrB2-based composites with in-situ synthesized ZrC from ZrO2 and graphite precursors
- 1 June 2020
- Published by Elsevier in Ceramics International
- Vol. 46 (9) , 13685-13694
Densification and toughening mechanisms in spark plasma sintered ZrB2-based composites with zirconium and graphite additives
- 1 June 2020
- Published by Elsevier in Ceramics International
- Vol. 46 (9) , 13685-13694
Densification and toughening mechanisms in spark plasma sintered ZrB2-based composites with zirconium and graphite additives