Yoshitomo Tanaka
Research Subjects
Yoshitomo Tanaka has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Takao Suzuki
The Center for Materials for Information Technology, The University of Alabama 1 , Tuscaloosa, Alabama 35487, USA
6 shared publications Gary Mankey
The Center for Materials for Information Technology, The University of Alabama 1 , Tuscaloosa, Alabama 35487, USA
5 shared publicationsClaudia Mewes
The Center for Materials for Information Technology, The University of Alabama 1 , Tuscaloosa, Alabama 35487, USA
2 shared publicationsIsao Kanada
Materials Development Center, TDK Corporation 2 , Narita, Chiba 286-0805, Japan
2 shared publicationsRainer Schad
The University of Alabama 1 The Center for Materials for Information Technology Tuscaloosa, Alabama 35487, USA
2 shared publications- Shuang Wu
Virginia Tech
2 shared publications
Latest Publications
- 14 January 2022
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 16 (10) , 2100574
No‐Heating Deposition of 1‐μm‐Thick Y‐Doped HfO2 Ferroelectric Films with Good Ferroelectric and Piezoelectric Properties by Radio Frequency Magnetron Sputtering Method
Y‐doped HfO2 ferroelectric films of ≈1 μm thick are deposited without heating by a radio frequency magnetron sputtering method. {100}‐oriented epitaxial films with orthorhombic phase are grown on (100)ITO//(100)YSZ substrates without heating. Their crystal structure is almost unchanged after postheat treatment at 800 °C. Ferroelectricity is confirmed for the no‐heating‐deposited films by polarization−electric field (P−E) curves, and their remanent polarization (Pr) and coercive fields are 12 μC cm−2 and 1.5 MV cm−1, respectively. These values are also almost unchanged after the postheat treatment. However, the postheat‐treated films show a lower breakdown electric field compared to the as‐deposited films without heat treatment. Approximately 1 μm‐thick films are also prepared without heating on (111)ITO/(111)Pt/TiOx/SiO2/(100)Si and (111)Pt/TiOx/SiO2/(100)Si substrates. Almost pure orthorhombic/tetragonal phase is deposited on both substrates without heating. The Pr value of the film on the (111)ITO/(111)Pt/TiOx/SiO2/(100)Si substrate is about 1.5 times larger than that on the (111)Pt/TiOx/SiO2/(100)Si substrate due to the better crystallinity of the film lattice‐matched with the underlying ITO layer. The effective piezoelectric constant (d33,f) of the film deposited on the (111)ITO/(111)Pt/TiOx/SiO2/(100)Si substrate without heating is estimated to be 4 pm V−1. The present low process temperature leads us to expect novel applications, especially for low‐heat‐resistance applications.
- 14 January 2022
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 16 (10) , 2100574
No‐Heating Deposition of 1‐μm‐Thick Y‐Doped HfO2 Ferroelectric Films with Good Ferroelectric and Piezoelectric Properties by Radio Frequency Magnetron Sputtering Method
Y‐doped HfO2 ferroelectric films of ≈1 μm thick are deposited without heating by a radio frequency magnetron sputtering method. {100}‐oriented epitaxial films with orthorhombic phase are grown on (100)ITO//(100)YSZ substrates without heating. Their crystal structure is almost unchanged after postheat treatment at 800 °C. Ferroelectricity is confirmed for the no‐heating‐deposited films by polarization−electric field (P−E) curves, and their remanent polarization (Pr) and coercive fields are 12 μC cm−2 and 1.5 MV cm−1, respectively. These values are also almost unchanged after the postheat treatment. However, the postheat‐treated films show a lower breakdown electric field compared to the as‐deposited films without heat treatment. Approximately 1 μm‐thick films are also prepared without heating on (111)ITO/(111)Pt/TiOx/SiO2/(100)Si and (111)Pt/TiOx/SiO2/(100)Si substrates. Almost pure orthorhombic/tetragonal phase is deposited on both substrates without heating. The Pr value of the film on the (111)ITO/(111)Pt/TiOx/SiO2/(100)Si substrate is about 1.5 times larger than that on the (111)Pt/TiOx/SiO2/(100)Si substrate due to the better crystallinity of the film lattice‐matched with the underlying ITO layer. The effective piezoelectric constant (d33,f) of the film deposited on the (111)ITO/(111)Pt/TiOx/SiO2/(100)Si substrate without heating is estimated to be 4 pm V−1. The present low process temperature leads us to expect novel applications, especially for low‐heat‐resistance applications.
- Open Access
- 1 March 2019
- Published by AIP Publishing in AIP Advances
- Vol. 9 (3) , 035032
Magnetic and structural properties of L1-Mn50Ga50-xAlx epitaxially grown thin films
Epitaxially grown L10- MnGa(Al) continuous thin films with the c-axis along the film normal are successfully fabricated on MgO (001) substrates at a substrate deposition temperature Ts of around 400 °C. The order parameter S is found to decrease with Al content, except for that for Al = 0. The films under consideration exhibit the perpendicular magnetic anisotropy constant Ku of about 1 x 107 erg/cm3 at 300 K. In order to clarify the magnetic anisotropy mechanism, the correlation between Ms(T) and Ku(T) is discussed. It is found that the values of n in the power law relation Ku(T) ∼ Ms(T)n are found to be 2.6, 2.3, and 2.0 for the films of 2.5, 5.6, 11.2 Al at%, respectively. The present result suggests that the magnetic anisotropy of L10-MnGaAl thin films may be explained in terms of the two-ion model, where both the contributions of Mn and Ga are significant to the total magnetic anisotropy”. The decrease of the value n with Al addition n is of interest, but the reason for this change is not understood at present.
- 1 March 2019
- Published by AIP Publishing in AIP Advances
- Vol. 9 (3) , 035032
Open AccessMagnetic and structural properties of L1-Mn50Ga50-xAlx epitaxially grown thin films
Epitaxially grown L10- MnGa(Al) continuous thin films with the c-axis along the film normal are successfully fabricated on MgO (001) substrates at a substrate deposition temperature Ts of around 400 °C. The order parameter S is found to decrease with Al content, except for that for Al = 0. The films under consideration exhibit the perpendicular magnetic anisotropy constant Ku of about 1 x 107 erg/cm3 at 300 K. In order to clarify the magnetic anisotropy mechanism, the correlation between Ms(T) and Ku(T) is discussed. It is found that the values of n in the power law relation Ku(T) ∼ Ms(T)n are found to be 2.6, 2.3, and 2.0 for the films of 2.5, 5.6, 11.2 Al at%, respectively. The present result suggests that the magnetic anisotropy of L10-MnGaAl thin films may be explained in terms of the two-ion model, where both the contributions of Mn and Ga are significant to the total magnetic anisotropy”. The decrease of the value n with Al addition n is of interest, but the reason for this change is not understood at present.
- Open Access
- 1 March 2019
- Published by AIP Publishing in AIP Advances
- Vol. 9 (3) , 035139
The thickness and growth temperature dependences of soft magnetic properties and an effective damping parameter of (FeCo)-Si alloy thin films
The dependences of magnetic properties and effective damping parameter (αeff) on film-thickness (d) and growth temperature (Ts) for Fe69Co26Si5 alloy films are investigated. The saturation magnetization (Ms) are found to decrease from approximately 1,700 to 1,500 emu/cm3 with d for Ts = 230 °C. For 40 nm films, the magnetization remains constant over the entire range of Ts from 35 to 360 °C. The coercivity (Hc) values for Ts above 120 °C are approximately 20 Oe. Those films deposited at Ts =120 °C or higher are epitaxial with the relation of FeCoSi//MgO in the film plane. For the films deposited at Ts =230 °C, the αeff rapidly decreases, and then slightly increases with d. The minimum αeff value of 0.002 is obtained at Ts = 230 °C.
- 1 March 2019
- Published by AIP Publishing in AIP Advances
- Vol. 9 (3) , 035139
Open AccessThe thickness and growth temperature dependences of soft magnetic properties and an effective damping parameter of (FeCo)-Si alloy thin films
The dependences of magnetic properties and effective damping parameter (αeff) on film-thickness (d) and growth temperature (Ts) for Fe69Co26Si5 alloy films are investigated. The saturation magnetization (Ms) are found to decrease from approximately 1,700 to 1,500 emu/cm3 with d for Ts = 230 °C. For 40 nm films, the magnetization remains constant over the entire range of Ts from 35 to 360 °C. The coercivity (Hc) values for Ts above 120 °C are approximately 20 Oe. Those films deposited at Ts =120 °C or higher are epitaxial with the relation of FeCoSi//MgO in the film plane. For the films deposited at Ts =230 °C, the αeff rapidly decreases, and then slightly increases with d. The minimum αeff value of 0.002 is obtained at Ts = 230 °C.
- Open Access
- 5 January 2018
- Published by AIP Publishing in AIP Advances
- Vol. 8 (5)
The growth temperature and measurement temperature dependences of soft magnetic properties and effective damping parameter of (FeCo)-Al alloy thin films
The soft magnetic properties and effective damping parameters of Fe73Co25Al2 alloy thin films are discussed. The effective damping parameter αeff measured by ferromagnetic resonance for the 10 nm-thick sample is nearly constant (≈0.004 ± 0.0008) for a growth temperature Ts from ambient to 200 °C, and then tends to decrease for higher temperatures and αeff is 0.002 ± 0.0004 at Ts = 300 °C. For the 80 nm-thick sample, the αeff seems to increase with Ts from αeff = 0.001 ± 0.0002 at Ts = ambient to αeff = 0.002 ± 0.0004. The αeff is found nearly constant (αeff = 0.004 ± 0.0008) over a temperature range from 10 to 300 K for the 10 nm films with the different Ts (ambient, 100 and 200 °C). Together with an increasing non-linearity of the frequency dependence of the linewidth at low Ts, extrinsic contributions such as two-magnon scattering dominate the observed temperature dependence of effective damping and linewidth.
- 5 January 2018
- Published by AIP Publishing in AIP Advances
- Vol. 8 (5)
Open AccessThe growth temperature and measurement temperature dependences of soft magnetic properties and effective damping parameter of (FeCo)-Al alloy thin films
The soft magnetic properties and effective damping parameters of Fe73Co25Al2 alloy thin films are discussed. The effective damping parameter αeff measured by ferromagnetic resonance for the 10 nm-thick sample is nearly constant (≈0.004 ± 0.0008) for a growth temperature Ts from ambient to 200 °C, and then tends to decrease for higher temperatures and αeff is 0.002 ± 0.0004 at Ts = 300 °C. For the 80 nm-thick sample, the αeff seems to increase with Ts from αeff = 0.001 ± 0.0002 at Ts = ambient to αeff = 0.002 ± 0.0004. The αeff is found nearly constant (αeff = 0.004 ± 0.0008) over a temperature range from 10 to 300 K for the 10 nm films with the different Ts (ambient, 100 and 200 °C). Together with an increasing non-linearity of the frequency dependence of the linewidth at low Ts, extrinsic contributions such as two-magnon scattering dominate the observed temperature dependence of effective damping and linewidth.
- Open Access
- 26 December 2017
- Published by AIP Publishing in AIP Advances
- Vol. 8 (5)
The temperature dependence of magnetic anisotropy of Nd-Fe-B thin films
The magnetic properties of Nd-Fe-B thin films with the three different compositions (#1: Nd12.6Fe81.5B5.9, #2: Nd14.6Fe78.1B7.4 and #3: Nd22.6Fe66.2B11.2) are discussed. With increasing Nd content, the c-axis orientation along the film normal is enhanced. It is found that sample #2 possesses the saturation magnetization Ms very close to that for Nd2Fe14B over a temperature range from 100 to about 300K. The magnetic anisotropy constant Ku2 for sample #2 is the highest among those samples, but smaller by about 20%, as compared to that for Nd2Fe14B. It is of interest to note that the temperature TR at which Ku1 changes its sign is lower by about 30K as compared to that previously reported for Nd2Fe14B. The reason for this discrepancy is not clear, but could be due to the presence of the minority phases of Nd-rich compounds and also a possible contribution of the magneto-elastic effect to the net magnetic anisotropy.
- 26 December 2017
- Published by AIP Publishing in AIP Advances
- Vol. 8 (5)
Open AccessThe temperature dependence of magnetic anisotropy of Nd-Fe-B thin films
The magnetic properties of Nd-Fe-B thin films with the three different compositions (#1: Nd12.6Fe81.5B5.9, #2: Nd14.6Fe78.1B7.4 and #3: Nd22.6Fe66.2B11.2) are discussed. With increasing Nd content, the c-axis orientation along the film normal is enhanced. It is found that sample #2 possesses the saturation magnetization Ms very close to that for Nd2Fe14B over a temperature range from 100 to about 300K. The magnetic anisotropy constant Ku2 for sample #2 is the highest among those samples, but smaller by about 20%, as compared to that for Nd2Fe14B. It is of interest to note that the temperature TR at which Ku1 changes its sign is lower by about 30K as compared to that previously reported for Nd2Fe14B. The reason for this discrepancy is not clear, but could be due to the presence of the minority phases of Nd-rich compounds and also a possible contribution of the magneto-elastic effect to the net magnetic anisotropy.
- Open Access
- 22 February 2017
- Published by AIP Publishing in AIP Advances
- Vol. 7 (5) , 056226
Magnetic properties and structure of low temperature phase MnBi with island structure
The magnetic properties of the low temperature phase (LTP) MnBi thin films of islands structure are discussed. The LTP MnBi islands are formed onto silica substrates after the multilayers Bi(3.2nm)/Mn(2nm)x N are deposited and then annealed at 450C for 0.5hr, where N is the number of the repetition of a pair of Mn and Bi layer. Those islands are found to be of the LTP MnBi, with the c-axis orientation along the normal to the sample plane for N=10 ∼ 40. Their size vary from place to place, but are averagely of about a few hundred nm in height and a few μm in width for N from 10 to 40. For N=200, the elongated islands are formed densely, with the length of about a few tens of μm. The coverage of those islands increases with N. The temperature dependence of saturation magnetization Ms is qualitatively similar to that for bulk, though the absolute values for Ms are smaller by 20%. The magnetic anisotropy constants of Ku1 and Ku2 are evaluated for the samples with N=10 ∼ 40, where Ku1 and Ku2 are the magnetic anisotropy constants corresponding to the second and fourth power term in the uniaxial magnetic anisotropy energy expression. It is found that the Ku1 increases with T monotonously, reaching to about 1x107 erg/cc at 400K. On the other hand, the Ku2 remains nearly zero for temperatures below 300K, and then becomes negative, reaching to about 7 x 106 erg/cc at 400K. This is the first to report of the temperature dependence of Ku1 and Ku2 in the LTP MnBi of an island structure. It is also noted that the decrease of Ku for a temperature range beyond around 450 K is possibly due to the decrease of the Ku2 component, as demonstrated in the present study.
- 22 February 2017
- Published by AIP Publishing in AIP Advances
- Vol. 7 (5) , 056226
Open AccessMagnetic properties and structure of low temperature phase MnBi with island structure
The magnetic properties of the low temperature phase (LTP) MnBi thin films of islands structure are discussed. The LTP MnBi islands are formed onto silica substrates after the multilayers Bi(3.2nm)/Mn(2nm)x N are deposited and then annealed at 450C for 0.5hr, where N is the number of the repetition of a pair of Mn and Bi layer. Those islands are found to be of the LTP MnBi, with the c-axis orientation along the normal to the sample plane for N=10 ∼ 40. Their size vary from place to place, but are averagely of about a few hundred nm in height and a few μm in width for N from 10 to 40. For N=200, the elongated islands are formed densely, with the length of about a few tens of μm. The coverage of those islands increases with N. The temperature dependence of saturation magnetization Ms is qualitatively similar to that for bulk, though the absolute values for Ms are smaller by 20%. The magnetic anisotropy constants of Ku1 and Ku2 are evaluated for the samples with N=10 ∼ 40, where Ku1 and Ku2 are the magnetic anisotropy constants corresponding to the second and fourth power term in the uniaxial magnetic anisotropy energy expression. It is found that the Ku1 increases with T monotonously, reaching to about 1x107 erg/cc at 400K. On the other hand, the Ku2 remains nearly zero for temperatures below 300K, and then becomes negative, reaching to about 7 x 106 erg/cc at 400K. This is the first to report of the temperature dependence of Ku1 and Ku2 in the LTP MnBi of an island structure. It is also noted that the decrease of Ku for a temperature range beyond around 450 K is possibly due to the decrease of the Ku2 component, as demonstrated in the present study.
- Open Access
- 29 February 2016
- Published by AIP Publishing in AIP Advances
- Vol. 6 (5) , 056008
Magnetic properties of low temperature phase MnBi of island structure
The magnetic and structural properties of island-structured LTP MnBi fabricated onto MgO single crystal substrates are discussed. The size and height of the “Volmer-Weber” type islands vary from place to place but are averagely a few microns and sub-microns, respectively. From the wetting angle (40 ∼ 60°) of those islands, the surface energy ΥMnBi of LTP MnBi is found to be 0.5∼0.8 J/m2. Those MnBi islands possesses the magnetic anisotropy constant Ku and saturation magnetization Ms close to those for bulk over a temperature range of 5 to 400 K. There seems to be a correlation between Ku and lattice constant c measured at 300K. The Ku is found to be inversely proportional to Ms5 over the temperature range from 5 K to 400 K, as compared to the Ms8 dependence for those fabricated onto fused silica glass substrates.
- 29 February 2016
- Published by AIP Publishing in AIP Advances
- Vol. 6 (5) , 056008
Open AccessMagnetic properties of low temperature phase MnBi of island structure
The magnetic and structural properties of island-structured LTP MnBi fabricated onto MgO single crystal substrates are discussed. The size and height of the “Volmer-Weber” type islands vary from place to place but are averagely a few microns and sub-microns, respectively. From the wetting angle (40 ∼ 60°) of those islands, the surface energy ΥMnBi of LTP MnBi is found to be 0.5∼0.8 J/m2. Those MnBi islands possesses the magnetic anisotropy constant Ku and saturation magnetization Ms close to those for bulk over a temperature range of 5 to 400 K. There seems to be a correlation between Ku and lattice constant c measured at 300K. The Ku is found to be inversely proportional to Ms5 over the temperature range from 5 K to 400 K, as compared to the Ms8 dependence for those fabricated onto fused silica glass substrates.