Keiji Onishi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Keiji Onishi has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
Makoto Tsubokura
RIKEN Center for Computational Science (R-CCS)
18 shared publications- Rahul Bale
Graduate School of System Informatics, Kobe University 1 , Kobe, Hyogo 6578501
6 shared publications Takuji Nakashima
Hiroshima University
5 shared publicationsNobuyuki Oshima
4 shared publicationsToshio Kobayashi
4 shared publicationsHuilai Zhang
3 shared publications
Latest Publications
- 1 March 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (3) , 033309
Numerical analysis of the efficiency of face masks for preventing droplet airborne infections
In this study, the flow field around face masks was visualized and evaluated using computational fluid dynamics. The protective efficiency of face masks suppressing droplet infection owing to differences in the shape, medium, and doubling usage is predicted. Under the ongoing COVID-19 pandemic condition, many studies have been conducted to highlight that airborne transmission is the possible transmission route. However, the virus infection prevention effect of face masks has not been sufficiently discussed and, thus, remains as a controversial issue. Therefore, we aimed to provide a beneficial index for the society. The topology-free immersed boundary method, which is advantageous for complex shapes, was used to model the flow in the constriction area, including the contact surface between the face and mask. The jet formed from the oral cavity flow out through the surface of the mask and leaks from the gap between the face and mask. A Darcy-type model of porous media was used to model the flow resistance of masks. A random variable stochastic model was used to measure particle transmittance. We evaluated the differences in the amount of leakage and deposition of the droplets during exhalation and inhalation, depending on the differences in the conditions between the surgical and cloth masks owing to coughing and breathing. The obtained results could be useful for epidemiological measures by numerically showing the particle suppression effect of the face mask. This includes both exhalation and inhalation.
- 1 March 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (3) , 033309
Numerical analysis of the efficiency of face masks for preventing droplet airborne infections
In this study, the flow field around face masks was visualized and evaluated using computational fluid dynamics. The protective efficiency of face masks suppressing droplet infection owing to differences in the shape, medium, and doubling usage is predicted. Under the ongoing COVID-19 pandemic condition, many studies have been conducted to highlight that airborne transmission is the possible transmission route. However, the virus infection prevention effect of face masks has not been sufficiently discussed and, thus, remains as a controversial issue. Therefore, we aimed to provide a beneficial index for the society. The topology-free immersed boundary method, which is advantageous for complex shapes, was used to model the flow in the constriction area, including the contact surface between the face and mask. The jet formed from the oral cavity flow out through the surface of the mask and leaks from the gap between the face and mask. A Darcy-type model of porous media was used to model the flow resistance of masks. A random variable stochastic model was used to measure particle transmittance. We evaluated the differences in the amount of leakage and deposition of the droplets during exhalation and inhalation, depending on the differences in the conditions between the surgical and cloth masks owing to coughing and breathing. The obtained results could be useful for epidemiological measures by numerically showing the particle suppression effect of the face mask. This includes both exhalation and inhalation.
- Open Access
Digital transformation of droplet/aerosol infection risk assessment realized on "Fugaku" for the fight against COVID-19
The fastest supercomputer in 2020, Fugaku, has not only achieved digital transformation of epidemiology in allowing end-to-end, detailed quantitative modeling of COVID-19 transmissions for the first time, but also transformed the behavior of the entire Japanese public through its detailed analysis of transmission risks in multitudes of societal situations entailing heavy risks. A novel aerosol simulation methodology was synthesized out of a combination of a new CFD methods meeting industrial demands, CUBE, which not only allowed the simulations to scale massively with high resolution required for micrometer virus-containing aerosol particles, but also extremely rapid time-to-solution due to its ability to generate the digital twins representing multitudes of societal situations in minutes not week, attaining true overall application high performance; such simulations have been running for the past 1.5 years on Fugaku, cumulatively consuming top supercomputer-class resources and the result communicated by the media as well as becoming official public policies.
Open AccessDigital transformation of droplet/aerosol infection risk assessment realized on "Fugaku" for the fight against COVID-19
The fastest supercomputer in 2020, Fugaku, has not only achieved digital transformation of epidemiology in allowing end-to-end, detailed quantitative modeling of COVID-19 transmissions for the first time, but also transformed the behavior of the entire Japanese public through its detailed analysis of transmission risks in multitudes of societal situations entailing heavy risks. A novel aerosol simulation methodology was synthesized out of a combination of a new CFD methods meeting industrial demands, CUBE, which not only allowed the simulations to scale massively with high resolution required for micrometer virus-containing aerosol particles, but also extremely rapid time-to-solution due to its ability to generate the digital twins representing multitudes of societal situations in minutes not week, attaining true overall application high performance; such simulations have been running for the past 1.5 years on Fugaku, cumulatively consuming top supercomputer-class resources and the result communicated by the media as well as becoming official public policies.
- 13 November 2021
- Published by Springer Nature
- p. 122-137
Nonlinear Mode Decomposition and Reduced-Order Modeling for Three-Dimensional Cylinder Flow by Distributed Learning on Fugaku
- 13 November 2021
- Published by Springer Nature
- p. 122-137
Nonlinear Mode Decomposition and Reduced-Order Modeling for Three-Dimensional Cylinder Flow by Distributed Learning on Fugaku
- 1 March 2020
- Published by Elsevier in Computers & Fluids
- Vol. 200, 104457
Stencil Penalty approach based constraint immersed boundary method
- 1 March 2020
- Published by Elsevier in Computers & Fluids
- Vol. 200, 104457
Stencil Penalty approach based constraint immersed boundary method
- Open Access
Topology-free immersed boundary method for incompressible turbulence flows: An aerodynamic simulation for 'dirty' CAD geometry
To design a method to solve the issues of handling 'dirty' and highly complex geometries, the topology-free method combined with the immersed boundary method is presented for viscous and incompressible flows at a high Reynolds number. The method simultaneously employs a ghost-cell technique and distributed forcing technique to impose the boundary conditions. An axis-projected interpolation scheme is used to avoid searching failures during fluid and solid identification. This method yields a topology-free immersed boundary, which particularly suits flow simulations of highly complex geometries. Difficulties generally arise when generating the calculation grid for these scenarios. This method allows dirty data to be handled without any preparatory treatment work to simplify or clean-up the geometry. This method is also applicable to the coherent structural turbulence model employed in this study. The verification cases, used in conjunction with the second-order central-difference scheme, resulted in first-order accuracy at finer resolution, although the coarser resolution retained second-order accuracy. This method is fully parallelized for distributed memory platforms. In this study, the accuracy and fidelity of this method were examined by simulating the flow around the bluff body, past a flat plate, and past dirty spheres. These simulations were compared with experimental data and other established results. Finally, results from the simulation of practical applications demonstrate the ability of the method to model highly complex, non-canonical three-dimensional flows. The countermeasure based on the accurate classification of geometric features has provided a robust and reasonable solution.
Open AccessTopology-free immersed boundary method for incompressible turbulence flows: An aerodynamic simulation for 'dirty' CAD geometry
To design a method to solve the issues of handling 'dirty' and highly complex geometries, the topology-free method combined with the immersed boundary method is presented for viscous and incompressible flows at a high Reynolds number. The method simultaneously employs a ghost-cell technique and distributed forcing technique to impose the boundary conditions. An axis-projected interpolation scheme is used to avoid searching failures during fluid and solid identification. This method yields a topology-free immersed boundary, which particularly suits flow simulations of highly complex geometries. Difficulties generally arise when generating the calculation grid for these scenarios. This method allows dirty data to be handled without any preparatory treatment work to simplify or clean-up the geometry. This method is also applicable to the coherent structural turbulence model employed in this study. The verification cases, used in conjunction with the second-order central-difference scheme, resulted in first-order accuracy at finer resolution, although the coarser resolution retained second-order accuracy. This method is fully parallelized for distributed memory platforms. In this study, the accuracy and fidelity of this method were examined by simulating the flow around the bluff body, past a flat plate, and past dirty spheres. These simulations were compared with experimental data and other established results. Finally, results from the simulation of practical applications demonstrate the ability of the method to model highly complex, non-canonical three-dimensional flows. The countermeasure based on the accurate classification of geometric features has provided a robust and reasonable solution.
- Open Access
- 1 January 2019
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Fluids engineering conference
- Vol. 2019, IS-23-23
Numerical Simulation of Combustion in a Rapid Compression Machine (RCM)
- 1 January 2019
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Fluids engineering conference
- Vol. 2019, IS-23-23
Open AccessNumerical Simulation of Combustion in a Rapid Compression Machine (RCM)
- 11 December 2018
- Published by SAGE Publications in The International Journal of High Performance Computing Applications
- Vol. 33 (4) , 678-698
CUBE: A scalable framework for large-scale industrial simulations
Writing high-performance solvers for engineering applications is a delicate task. These codes are often developed on an application to application basis, highly optimized to solve a certain problem. Here, we present our work on developing a general simulation framework for efficient computation of time-resolved approximations of complex industrial flow problems—Complex Unified Building cube method (CUBE). To address the challenges of emerging, modern supercomputers, suitable data structures and communication patterns are developed and incorporated into CUBE. We use a Cartesian grid together with various immersed boundary (IB) methods to accurately capture moving, complex geometries. The asymmetric workload of the IB is balanced by a predictive dynamic load balancer, and a multithreaded halo exchange algorithm is employed to efficiently overlap communication with computations. Our work also concerns efficient methods for handling the large amount of data produced by large-scale flow simulations, such as scalable parallel I/O, data compression, and in-situ processing.
- 11 December 2018
- Published by SAGE Publications in The International Journal of High Performance Computing Applications
- Vol. 33 (4) , 678-698
CUBE: A scalable framework for large-scale industrial simulations
Writing high-performance solvers for engineering applications is a delicate task. These codes are often developed on an application to application basis, highly optimized to solve a certain problem. Here, we present our work on developing a general simulation framework for efficient computation of time-resolved approximations of complex industrial flow problems—Complex Unified Building cube method (CUBE). To address the challenges of emerging, modern supercomputers, suitable data structures and communication patterns are developed and incorporated into CUBE. We use a Cartesian grid together with various immersed boundary (IB) methods to accurately capture moving, complex geometries. The asymmetric workload of the IB is balanced by a predictive dynamic load balancer, and a multithreaded halo exchange algorithm is employed to efficiently overlap communication with computations. Our work also concerns efficient methods for handling the large amount of data produced by large-scale flow simulations, such as scalable parallel I/O, data compression, and in-situ processing.
- 3 April 2018
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Evaluation of an Open-grill Vehicle Aerodynamics Simulation Method Considering Dirty CAD Geometries
In open-grille vehicle aerodynamics simulation using computational fluid dynamics, in addition to basic flow characteristics, such as turbulent flow with a Reynolds number of several million on the bluff body, it is important to accurately estimate the cooling air flow introduced from the front opening. It is therefore necessary to reproduce the detailed geometry of the entire vehicle including the engine bay as precisely as possible. However, there is a problem of generating a good-quality calculation grid with a small workload. It usually takes several days to a week for the pretreatment process to make the geometry data ‘clean’ or ‘watertight’. The authors proposed a computational method for complex geometries with a hierarchical Cartesian grid and a topology-independent immersed boundary method with dummy cells that discretize the geometry on a cell-by-cell basis and can set an imaginary point arbitrarily. It is possible to avoid problems of ‘dirty’ computer-aided-design data, such as a gap/overlap and a zero-thickness surface. The present study applied this method to the several full vehicle models. The results were compared with the results of a conventional method based on an unstructured grid. A resolution of about 6 mm was adopted, and the number of cells ranged from tens of millions to 100 million. Preprocessing in the conventional method takes 2 weeks, and improvements to the calculation speed using hundreds of cores have reached a limit. In the present method, preliminary processing was shortened to 10 minutes, and the calculation speed was scaled up to several thousand cores, thanks to the simplification of calculation by the Cartesian grid. Differences in the drag coefficient due to the effect of aerodynamic parts were almost comparable. Because the present method has higher parallel computing efficiency, it is suited to massively parallel environments that will emerge in the near future.
- 3 April 2018
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Evaluation of an Open-grill Vehicle Aerodynamics Simulation Method Considering Dirty CAD Geometries
In open-grille vehicle aerodynamics simulation using computational fluid dynamics, in addition to basic flow characteristics, such as turbulent flow with a Reynolds number of several million on the bluff body, it is important to accurately estimate the cooling air flow introduced from the front opening. It is therefore necessary to reproduce the detailed geometry of the entire vehicle including the engine bay as precisely as possible. However, there is a problem of generating a good-quality calculation grid with a small workload. It usually takes several days to a week for the pretreatment process to make the geometry data ‘clean’ or ‘watertight’. The authors proposed a computational method for complex geometries with a hierarchical Cartesian grid and a topology-independent immersed boundary method with dummy cells that discretize the geometry on a cell-by-cell basis and can set an imaginary point arbitrarily. It is possible to avoid problems of ‘dirty’ computer-aided-design data, such as a gap/overlap and a zero-thickness surface. The present study applied this method to the several full vehicle models. The results were compared with the results of a conventional method based on an unstructured grid. A resolution of about 6 mm was adopted, and the number of cells ranged from tens of millions to 100 million. Preprocessing in the conventional method takes 2 weeks, and improvements to the calculation speed using hundreds of cores have reached a limit. In the present method, preliminary processing was shortened to 10 minutes, and the calculation speed was scaled up to several thousand cores, thanks to the simplification of calculation by the Cartesian grid. Differences in the drag coefficient due to the effect of aerodynamic parts were almost comparable. Because the present method has higher parallel computing efficiency, it is suited to massively parallel environments that will emerge in the near future.
- Open Access
- 28 January 2018
- Published by Association for Computing Machinery (ACM)
- p. 278-288
A Study on Open Source Software for Large-Scale Data Visualization on SPARC64fx based HPC Systems
- 28 January 2018
- Published by Association for Computing Machinery (ACM)
- p. 278-288
Open AccessA Study on Open Source Software for Large-Scale Data Visualization on SPARC64fx based HPC Systems