Sabina Huč
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Sabina Huč has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Staffan Svensson
University of Borås , Faculty of Textiles, Engineering and Business , SE-501 90 Borås , Sweden
3 shared publicationsTomaž Hozjan
Faculty of Civil and Geodetic Engineering, University of Ljubljana, Ljubljana, Slovenia
3 shared publications- Boris Azinović
ZAG Ljubljana
1 shared publication - Francesco Mirko Massaro
Norwegian University of Science and Technology
1 shared publication - Haris Stamatopoulos
Norwegian University of Science and Technology
1 shared publication Igor Planinc
Faculty of Civil and Geodetic Engineering, University of Ljubljana, Ljubljana, Slovenia
1 shared publication
Latest Publications
- Open Access
- 15 October 2026
- Published by Springer Nature
- p. 1093-1101
The Effect of Wood Rheology on Reusability of Timber Products
- 15 October 2026
- Published by Springer Nature
- p. 1093-1101
Open AccessThe Effect of Wood Rheology on Reusability of Timber Products
- Open Access
- 1 April 2025
- Published by Elsevier in Structures
- Vol. 75
A new numerical model for analysing timber-concrete composite beams under fire conditions
- 1 April 2025
- Published by Elsevier in Structures
- Vol. 75
Open AccessA new numerical model for analysing timber-concrete composite beams under fire conditions
- 9 August 2021
- Published by Springer Nature in Acta Mechanica
- Vol. 232 (10) , 3977-3996
An analytical solution of the elastic concrete ring under restrained shrinkage, considering an interlayer slip
- 9 August 2021
- Published by Springer Nature in Acta Mechanica
- Vol. 232 (10) , 3977-3996
An analytical solution of the elastic concrete ring under restrained shrinkage, considering an interlayer slip
- Open Access
- 17 December 2020
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 75 (7) , 655-667
Wood-adhesive bond loaded in mode II: experimental and numerical analysis using elasto-plastic and fracture mechanics models
The goal of the study was to analyze fracture properties of adhesive bond using a three-point end-notched flexure test and the compliance-based beam method. Critical strain energy release rates (G IIc ) and cohesive laws were obtained for adhesive bonds made of European beech (Fagus sylvatica L.) and adhesives such as EPI, MUF, PRF and PUR. The experiments were assisted with FE analyses employing three different material models of wood: elastic (Elas), symmetric elasto-plastic (EP) and elasto-plastic with different compressive and tensile yield stresses parallel to fiber (EP+). The highest mean G IIc was achieved for PUR (5.40 Nmm−1) and then decreased as follows: 2.33, 1.80, 1.59 Nmm−1 for MUF, EPI, and PRF, respectively. The failure of bondline was brittle and occurred at bondline for EPI, MUF and PRF, and ductile and commonly occurring in wood for PUR adhesive. The FE simulations employing cohesive models agreed well with the experimental findings for all adhesives. FE model with Elas material was found accurate enough for EPI, MUF and PRF adhesives. For PUR adhesive, the model EP+ was found to be the most accurate in prediction of maximal force. The impact of friction between lamellas may be up to 4.2% when varying friction coefficient from 0 to 1. The impact of the grain angle distortion (α) with respect to longitudinal specimen axis showed its high influence on resulting stiffness and maximal force. It was found that three-point end-notched test is suitable for EPI, MUF, and PRF, while it is less appropriate for a bond with PUR adhesive due to notable plastic behavior.
- 17 December 2020
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 75 (7) , 655-667
Open AccessWood-adhesive bond loaded in mode II: experimental and numerical analysis using elasto-plastic and fracture mechanics models
The goal of the study was to analyze fracture properties of adhesive bond using a three-point end-notched flexure test and the compliance-based beam method. Critical strain energy release rates (G IIc ) and cohesive laws were obtained for adhesive bonds made of European beech (Fagus sylvatica L.) and adhesives such as EPI, MUF, PRF and PUR. The experiments were assisted with FE analyses employing three different material models of wood: elastic (Elas), symmetric elasto-plastic (EP) and elasto-plastic with different compressive and tensile yield stresses parallel to fiber (EP+). The highest mean G IIc was achieved for PUR (5.40 Nmm−1) and then decreased as follows: 2.33, 1.80, 1.59 Nmm−1 for MUF, EPI, and PRF, respectively. The failure of bondline was brittle and occurred at bondline for EPI, MUF and PRF, and ductile and commonly occurring in wood for PUR adhesive. The FE simulations employing cohesive models agreed well with the experimental findings for all adhesives. FE model with Elas material was found accurate enough for EPI, MUF and PRF adhesives. For PUR adhesive, the model EP+ was found to be the most accurate in prediction of maximal force. The impact of friction between lamellas may be up to 4.2% when varying friction coefficient from 0 to 1. The impact of the grain angle distortion (α) with respect to longitudinal specimen axis showed its high influence on resulting stiffness and maximal force. It was found that three-point end-notched test is suitable for EPI, MUF, and PRF, while it is less appropriate for a bond with PUR adhesive due to notable plastic behavior.
- 8 November 2019
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 74 (5) , 445-457
Numerical analysis of moisture-induced strains and stresses in glued-laminated timber
Changes in relative humidity of the ambient air, RH (%), cause wetting and drying of wood material, which results in non-uniform moisture contents or moisture gradients, and consequently in moisture-induced stresses and strains in the glued-laminated timber (glulam) members. The aim of the present paper is to perform a hygro-mechanical analysis to predict the mechanical behavior of glulam specimens exposed to two RH regimes, causing wetting from 50% to 90% RH and drying from 90% to 50% RH, and compare the numerical to the experimental results. The aims are also to quantitatively analyze the influence of characteristic material parameters required in the multi-Fickian moisture transport model and the mechanical model on moisture-induced strains and stresses in glulam specimens and to determine the possibility of cracking of the material by analyzing the maximum tensile stresses perpendicular to the grain. Accurate numerical predictions of moisture contents and moisture-induced strains are obtained in the glulam specimens during wetting and drying as compared to the experimental results. The influence of a particular characteristic material parameter on moisture-induced strains and stresses is characterized as significant, but not crucial when a rough numerical estimation of the mechanical behavior of the glulam beam exposed to RH changes is required.
- 8 November 2019
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 74 (5) , 445-457
Numerical analysis of moisture-induced strains and stresses in glued-laminated timber
Changes in relative humidity of the ambient air, RH (%), cause wetting and drying of wood material, which results in non-uniform moisture contents or moisture gradients, and consequently in moisture-induced stresses and strains in the glued-laminated timber (glulam) members. The aim of the present paper is to perform a hygro-mechanical analysis to predict the mechanical behavior of glulam specimens exposed to two RH regimes, causing wetting from 50% to 90% RH and drying from 90% to 50% RH, and compare the numerical to the experimental results. The aims are also to quantitatively analyze the influence of characteristic material parameters required in the multi-Fickian moisture transport model and the mechanical model on moisture-induced strains and stresses in glulam specimens and to determine the possibility of cracking of the material by analyzing the maximum tensile stresses perpendicular to the grain. Accurate numerical predictions of moisture contents and moisture-induced strains are obtained in the glulam specimens during wetting and drying as compared to the experimental results. The influence of a particular characteristic material parameter on moisture-induced strains and stresses is characterized as significant, but not crucial when a rough numerical estimation of the mechanical behavior of the glulam beam exposed to RH changes is required.
- Open Access
- 9 February 2018
- Published by Springer Nature in Wood Science and Technology
- Vol. 52 (3) , 793-808
Rheological behavior of wood in stress relaxation under compression
- 9 February 2018
- Published by Springer Nature in Wood Science and Technology
- Vol. 52 (3) , 793-808
Open AccessRheological behavior of wood in stress relaxation under compression
- Open Access
- 24 August 2017
- Published by Springer Nature in Wood Science and Technology
- Vol. 52 (1) , 29-43
Coupled two-dimensional modeling of viscoelastic creep of wood
- 24 August 2017
- Published by Springer Nature in Wood Science and Technology
- Vol. 52 (1) , 29-43
Open AccessCoupled two-dimensional modeling of viscoelastic creep of wood