Mohamed Lamine Fares
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mohamed Lamine Fares has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
- David Piot
University Lyon
5 shared publications F. Montheillet
3 shared publicationsM. Belaid
Badji-Mokhtar University of Annaba/Laboratory of Metallurgy and Materials Engineering P.O. Box 12 El Hadjar 23000 Annaba Algeria
3 shared publicationsO. Chahaoui
Sciences and Technology Institute, Laghrour Abbes University, Khenchela, Algeria
3 shared publications- Frank Montheillet
University Lyon
2 shared publications H. Ghous
Metallurgy and Materials Engineering Laboratory (LMGM), Metallurgy and Material Engineering Department, Badji Mokhtar University, Algeria
2 shared publications
Latest Publications
- 12 January 2022
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 53 (1) , 15-38
Surface characterization of a modified cold work tool steel treated by powder‐pack boronizing
The present work examines the effects of pack‐boronizing treatment on the surface characteristics of modified industrial cold‐work tool steel intended for polymer crushing. Particular attention is paid to optimizing the process parameters to improve the tool surface properties and thus achieve a satisfactory tool life. To this end, a series of samples were subjected to boronizing treatment within the temperature range from 800 °C to 1000 °C for soaking periods of 2 h, 4 h, 6 h and 8 h. The structural and mechanical properties of the modified metal surface were analyzed using optical and scanning electron microscopy, x‐ray diffraction, microhardness testing and pin‐on‐disk tribotesting. The adhesion quality of the boride layer‐substrate was carried out using the adhesion test Daimler Benz Rockwell‐C. The corrosion properties were determined by the electrochemical polarization method. Experimental results showed that the optimum temperature‐temporal conditions of 900 °C/4 h that are the intermediate processing parameters led to a better compromise between the intended properties, in terms of resistance to wear and corrosion, as well as adhesion quality.
- 12 January 2022
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 53 (1) , 15-38
Surface characterization of a modified cold work tool steel treated by powder‐pack boronizing
The present work examines the effects of pack‐boronizing treatment on the surface characteristics of modified industrial cold‐work tool steel intended for polymer crushing. Particular attention is paid to optimizing the process parameters to improve the tool surface properties and thus achieve a satisfactory tool life. To this end, a series of samples were subjected to boronizing treatment within the temperature range from 800 °C to 1000 °C for soaking periods of 2 h, 4 h, 6 h and 8 h. The structural and mechanical properties of the modified metal surface were analyzed using optical and scanning electron microscopy, x‐ray diffraction, microhardness testing and pin‐on‐disk tribotesting. The adhesion quality of the boride layer‐substrate was carried out using the adhesion test Daimler Benz Rockwell‐C. The corrosion properties were determined by the electrochemical polarization method. Experimental results showed that the optimum temperature‐temporal conditions of 900 °C/4 h that are the intermediate processing parameters led to a better compromise between the intended properties, in terms of resistance to wear and corrosion, as well as adhesion quality.
- 20 November 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 126538
Influence of niobium solutes on the microstructural evolution of nickel during hot working
- 20 November 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 126538
Influence of niobium solutes on the microstructural evolution of nickel during hot working
- 17 September 2019
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 297, 31-50
Constitutive Modelling of an Industrial Rolled Sheet for a DIN 1623 St14 (DC04) Steel
The comprehension of the anisotropy impacts on mechanical properties of the rolled steel sheets was investigated using a non-quadratic anisotropic yield function. In this study, experimental and modelling determination of behavior of an industrial rolled sheets for a DIN 1623 St14 steel were carried out. The yield stresses and Lankford r-values in uniaxial were experimentally determined but the balanced biaxial tension stress states and rb were assumed. The parameters of the associated yield equation, derived from the three orthotropic yield functions proposed by Hill48 and Yld2000-2d, were determined. Predictions and the evolution of normalized yield stress and normalized Lankford parameters (plastic strain ratio) obtained by the presented investigative are considered. In order to describe the path of equivalent plastic behavior, the isotropic hardening function is described using the following various empirical standard formulae based on: Hollomon, Ludwick, Swift and Voce model.
- 17 September 2019
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 297, 31-50
Constitutive Modelling of an Industrial Rolled Sheet for a DIN 1623 St14 (DC04) Steel
The comprehension of the anisotropy impacts on mechanical properties of the rolled steel sheets was investigated using a non-quadratic anisotropic yield function. In this study, experimental and modelling determination of behavior of an industrial rolled sheets for a DIN 1623 St14 steel were carried out. The yield stresses and Lankford r-values in uniaxial were experimentally determined but the balanced biaxial tension stress states and rb were assumed. The parameters of the associated yield equation, derived from the three orthotropic yield functions proposed by Hill48 and Yld2000-2d, were determined. Predictions and the evolution of normalized yield stress and normalized Lankford parameters (plastic strain ratio) obtained by the presented investigative are considered. In order to describe the path of equivalent plastic behavior, the isotropic hardening function is described using the following various empirical standard formulae based on: Hollomon, Ludwick, Swift and Voce model.
- 26 December 2018
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 941, 2264-2269
The Avrami Kinetics of Dynamic Recrystallization in Nickel-Niobium Alloys
The flow curves determined on a series of Ni-Nb alloys are analysed. Six alloys containing Ni–0.01, 0.1, 1, 2, 5 and 10 wt. % Nb with pure Ni were tested in torsion at various strain rates within the hot forging temperature range. Under these conditions, large strains were attained, which permitted steady state flow to take place. The double-differentiation method is employed to define the critical strain for the initiation of DRX, leading to the evaluation of the strain hardening and dynamic recovery parameters. The relations obtained are compared to ones determined earlier using a least squares approach. It is shown that the two sets of relations do not differ appreciably. These results are employed to predict the Avrami kinetics of a range of Ni-Nb alloys strained at different temperatures and strain rates. The Avrami time exponents all fall in the range 1.0 to 5.0. The dependence of the time of half-softening, t50, on Nb content, strain rate and temperature is also derived under the same conditions.
- 26 December 2018
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 941, 2264-2269
The Avrami Kinetics of Dynamic Recrystallization in Nickel-Niobium Alloys
The flow curves determined on a series of Ni-Nb alloys are analysed. Six alloys containing Ni–0.01, 0.1, 1, 2, 5 and 10 wt. % Nb with pure Ni were tested in torsion at various strain rates within the hot forging temperature range. Under these conditions, large strains were attained, which permitted steady state flow to take place. The double-differentiation method is employed to define the critical strain for the initiation of DRX, leading to the evaluation of the strain hardening and dynamic recovery parameters. The relations obtained are compared to ones determined earlier using a least squares approach. It is shown that the two sets of relations do not differ appreciably. These results are employed to predict the Avrami kinetics of a range of Ni-Nb alloys strained at different temperatures and strain rates. The Avrami time exponents all fall in the range 1.0 to 5.0. The dependence of the time of half-softening, t50, on Nb content, strain rate and temperature is also derived under the same conditions.
- 15 November 2016
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 879, 1251-1257
Influence of Niobium Content on the Hot Mechanical Behavior of Nickel Alloys
Nickel-base superalloys are usually employed for large forged parts in aerospace industry. A comprehensive understanding of their mechanical behavior during hot working is required, especially for manufacturers in order to enhance the in-service properties. In this context, the first part of the work aims at investigating the mechanical behavior of nickel during hot deformation, with particular emphasis on the influence of niobium additions in solid solution. For this purpose, a series of wrought model alloys including pure nickel and Ni-Nb alloys (Ni-0.01, 0.1, 1, 2, 5 and 10 wt. % Nb) were prepared and deformed by hot torsion at temperatures ranging from 800 to 1000 °C degrees and at three (von Mises equivalent) strain rates of 0.03, 0.1 and 0.3 s-1. Afterwards, the key rheological parameters that characterize strain hardening and dynamic recovery were determined through a simple analytical method based on the classical Laasraoui-Jonas constitutive equation, allowing reasonable fit for the flow curves for all studied Ni-Nb alloys. In this way, the effect of niobium solutes on the fundamental mechanisms of deformation was well highlighted. In the second part, three usual models describing strain hardening and dynamic recovery, referred to as the Laasraoui-Jonas (LJ), Kocks-Mecking (KM), and power law (PW) equations are compared within the range of moderate strains. Transformation formulae are derived, allowing the parameters of one law to be computed from the parameters of any of the two others. The theoretical derivations are illustrated by the specific case of a Ni-Nb alloy in the solid solution domain.
- 15 November 2016
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 879, 1251-1257
Influence of Niobium Content on the Hot Mechanical Behavior of Nickel Alloys
Nickel-base superalloys are usually employed for large forged parts in aerospace industry. A comprehensive understanding of their mechanical behavior during hot working is required, especially for manufacturers in order to enhance the in-service properties. In this context, the first part of the work aims at investigating the mechanical behavior of nickel during hot deformation, with particular emphasis on the influence of niobium additions in solid solution. For this purpose, a series of wrought model alloys including pure nickel and Ni-Nb alloys (Ni-0.01, 0.1, 1, 2, 5 and 10 wt. % Nb) were prepared and deformed by hot torsion at temperatures ranging from 800 to 1000 °C degrees and at three (von Mises equivalent) strain rates of 0.03, 0.1 and 0.3 s-1. Afterwards, the key rheological parameters that characterize strain hardening and dynamic recovery were determined through a simple analytical method based on the classical Laasraoui-Jonas constitutive equation, allowing reasonable fit for the flow curves for all studied Ni-Nb alloys. In this way, the effect of niobium solutes on the fundamental mechanisms of deformation was well highlighted. In the second part, three usual models describing strain hardening and dynamic recovery, referred to as the Laasraoui-Jonas (LJ), Kocks-Mecking (KM), and power law (PW) equations are compared within the range of moderate strains. Transformation formulae are derived, allowing the parameters of one law to be computed from the parameters of any of the two others. The theoretical derivations are illustrated by the specific case of a Ni-Nb alloy in the solid solution domain.
- 23 December 2014
- Published by Wiley in Steel Research International
- Vol. 86 (9) , 1090-1103
Comparing the Hot Ductility Behaviour of Low-Carbon Microalloyed Nb-V-Ti Steels During Two Thermal Cycling Routes: Solutionizing and Precipitation Treatments
- 23 December 2014
- Published by Wiley in Steel Research International
- Vol. 86 (9) , 1090-1103
Comparing the Hot Ductility Behaviour of Low-Carbon Microalloyed Nb-V-Ti Steels During Two Thermal Cycling Routes: Solutionizing and Precipitation Treatments
- 17 June 2014
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 45 (10) , 4324-4332
A Critical Assessment of Three Usual Equations for Strain Hardening and Dynamic Recovery
- 17 June 2014
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 45 (10) , 4324-4332
A Critical Assessment of Three Usual Equations for Strain Hardening and Dynamic Recovery
- 1 December 2013
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 586, 350-357
Influence of niobium solutes on the mechanical behavior of nickel during hot working
- 1 December 2013
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 586, 350-357
Influence of niobium solutes on the mechanical behavior of nickel during hot working
- 10 September 2013
- Published by Springer Nature in Metals and Materials International
- Vol. 19 (5) , 1005-1019
Mechanical modeling of macroscopic behavior for anisotropic and heterogeneous metal alloys
- 10 September 2013
- Published by Springer Nature in Metals and Materials International
- Vol. 19 (5) , 1005-1019
Mechanical modeling of macroscopic behavior for anisotropic and heterogeneous metal alloys