Li Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Li Zhou has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Song Hu
Tongren University College of Agriculture and Forestry Engineering and Planning Tongren
5 shared publications Yong Huang
5 shared publications- Yong Huang
Guizhou University College of Architecture and Urban Planning Guiyang
5 shared publications Song Hu
4 shared publicationsHonggang Tang
3 shared publicationsHuanyi Wang
3 shared publications
Latest Publications
- 5 October 2026
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Structures and Buildings
- p. 1-17
Behaviour analysis of phosphogypsum-filled cold-formed steel walls under different lateral loading patterns
Full-scale phosphogypsum-filled cold-formed steel (PFCFS) composite walls were tested under quasi-static loading to investigate their behaviour and damage characteristics under different lateral loading patterns, including monotonic loading, cyclic loading followed by monotonic loading, and cyclic loading. The results showed similar failure modes and predominantly ductile behaviour. However, the loading patterns significantly influenced damage accumulation and seismic performance degradation. Cyclic loading accelerated damage development in sheathing connections and phosphogypsum infill, resulting in notable reductions in stiffness, deformation capacity, energy dissipation and ductility. The Park–Ang damage model was employed to evaluate damage evolution, and five performance levels were defined: intact, minor damage, moderate damage, severe damage and failure. Findings provide a reference framework for the seismic evaluation and design of PFCFS walls.
- 5 October 2026
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Structures and Buildings
- p. 1-17
Behaviour analysis of phosphogypsum-filled cold-formed steel walls under different lateral loading patterns
Full-scale phosphogypsum-filled cold-formed steel (PFCFS) composite walls were tested under quasi-static loading to investigate their behaviour and damage characteristics under different lateral loading patterns, including monotonic loading, cyclic loading followed by monotonic loading, and cyclic loading. The results showed similar failure modes and predominantly ductile behaviour. However, the loading patterns significantly influenced damage accumulation and seismic performance degradation. Cyclic loading accelerated damage development in sheathing connections and phosphogypsum infill, resulting in notable reductions in stiffness, deformation capacity, energy dissipation and ductility. The Park–Ang damage model was employed to evaluate damage evolution, and five performance levels were defined: intact, minor damage, moderate damage, severe damage and failure. Findings provide a reference framework for the seismic evaluation and design of PFCFS walls.
- Open Access
- 5 December 2025
- Published by Elsevier in Energy Reports
- Vol. 14, 5401-5413
Indoor thermal environment of traditional Chinese wooden residential buildings: A case study in Guizhou, China
- 5 December 2025
- Published by Elsevier in Energy Reports
- Vol. 14, 5401-5413
Open AccessIndoor thermal environment of traditional Chinese wooden residential buildings: A case study in Guizhou, China
- 5 September 2025
- Published by Elsevier in Structures
- Vol. 80
Behavior of cold-formed thin-walled steel walls filled with phosphogypsum under monotonic lateral loading: Tests and simulations
- 5 September 2025
- Published by Elsevier in Structures
- Vol. 80
Behavior of cold-formed thin-walled steel walls filled with phosphogypsum under monotonic lateral loading: Tests and simulations
- 17 April 2025
- Published by Elsevier in Structures
- Vol. 76
Experimental and numerical study on axial compression performance of cold-formed thin-walled steel walls filled with phosphogypsum
- 17 April 2025
- Published by Elsevier in Structures
- Vol. 76
Experimental and numerical study on axial compression performance of cold-formed thin-walled steel walls filled with phosphogypsum
- 1 January 2025
- Published by ELS Publishing Co. Limited in Proceedings: Engineering
- Vol. 2, 1-2
Fire resistance of square timber columns: simplified models for predicting the charring rate and failure time
To study the fire resistance performance of square timber columns, fire test data were collected, and the charring depth of timber columns was analyzed in detail. An optimization model for predicting ...
- 1 January 2025
- Published by ELS Publishing Co. Limited in Proceedings: Engineering
- Vol. 2, 1-2
Fire resistance of square timber columns: simplified models for predicting the charring rate and failure time
To study the fire resistance performance of square timber columns, fire test data were collected, and the charring depth of timber columns was analyzed in detail. An optimization model for predicting ...
- 9 December 2024
- Published by SAGE Publications in Indoor and Built Environment
- Vol. 34 (2) , 460-476
Impact of windows on the indoor thermal environment of Chinese Chuandou-style timber residential houses: Tests and simulations
Model tests and simulations were conducted to investigate the influence of windows on the thermal environment of Chinese Chuandou-style timber residential houses. Besides, the thermal comfort of the house was also analyzed. The test results indicated that the measured temperature curves have obvious five-stage characteristics. The air temperature in the attic during the daytime was higher than that in the room, especially when the windows were open. During the daytime, when the windows were closed, the indoor air temperature was higher than the outdoor air temperature, while when the windows were fully open, the opposite pattern was observed. Numerical simulations showed that increasing the window–wall ratio could lead to an increase in indoor air temperature during the daytime, and decreasing the window width–height ratio would slightly reduce the indoor air temperature. The window opening degree has a significant impact on the indoor thermal environment, the higher the window opening degree, the lower the indoor air temperature during the daytime. Further, reducing the window heat transfer coefficient could also lead to a slight increase in indoor air temperature. The thermal comfort of the house was poor during the daytime in summer, but it was slightly improved when the windows were open.
- 9 December 2024
- Published by SAGE Publications in Indoor and Built Environment
- Vol. 34 (2) , 460-476
Impact of windows on the indoor thermal environment of Chinese Chuandou-style timber residential houses: Tests and simulations
Model tests and simulations were conducted to investigate the influence of windows on the thermal environment of Chinese Chuandou-style timber residential houses. Besides, the thermal comfort of the house was also analyzed. The test results indicated that the measured temperature curves have obvious five-stage characteristics. The air temperature in the attic during the daytime was higher than that in the room, especially when the windows were open. During the daytime, when the windows were closed, the indoor air temperature was higher than the outdoor air temperature, while when the windows were fully open, the opposite pattern was observed. Numerical simulations showed that increasing the window–wall ratio could lead to an increase in indoor air temperature during the daytime, and decreasing the window width–height ratio would slightly reduce the indoor air temperature. The window opening degree has a significant impact on the indoor thermal environment, the higher the window opening degree, the lower the indoor air temperature during the daytime. Further, reducing the window heat transfer coefficient could also lead to a slight increase in indoor air temperature. The thermal comfort of the house was poor during the daytime in summer, but it was slightly improved when the windows were open.
- 1 July 2024
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Structures and Buildings
- Vol. 177 (7) , 569-588
Effect of wall sheathings on seismic behaviour of phosphogypsum-filled CFS shear walls
To improve the seismic behaviour of cold-formed steel (CFS) walls, a novel infilled CFS wall covered with different wall sheathings (gypsum wallboard, oriented strand board and fibre cement board) was assessed. Four full-scale specimens were tested under cyclic lateral loads to investigate the impacts of the wall sheathings on the seismic performance of the CFS wall. The failure process, failure mode, load–displacement curve, strength degradation, stiffness degradation, energy dissipation, deformation and strain variation of the walls were investigated. The failure modes of the walls were found to be failure of the connections between the CFS frame and the sheathing as well as crushing of the infill material. Compared with a specimen without sheathing, the peak load and lateral stiffness of the walls with sheathing were increased by 1.25–1.72 times, indicating that the sheathings played an important role in the lateral resistance of the wall. An analysis model and formulas for predicting wall lateral stiffness were developed. Comparisons between the calculations and experimental data showed that the proposed theoretical method was able to predict the lateral stiffness of the infilled CFS walls accurately.
- 1 July 2024
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Structures and Buildings
- Vol. 177 (7) , 569-588
Effect of wall sheathings on seismic behaviour of phosphogypsum-filled CFS shear walls
To improve the seismic behaviour of cold-formed steel (CFS) walls, a novel infilled CFS wall covered with different wall sheathings (gypsum wallboard, oriented strand board and fibre cement board) was assessed. Four full-scale specimens were tested under cyclic lateral loads to investigate the impacts of the wall sheathings on the seismic performance of the CFS wall. The failure process, failure mode, load–displacement curve, strength degradation, stiffness degradation, energy dissipation, deformation and strain variation of the walls were investigated. The failure modes of the walls were found to be failure of the connections between the CFS frame and the sheathing as well as crushing of the infill material. Compared with a specimen without sheathing, the peak load and lateral stiffness of the walls with sheathing were increased by 1.25–1.72 times, indicating that the sheathings played an important role in the lateral resistance of the wall. An analysis model and formulas for predicting wall lateral stiffness were developed. Comparisons between the calculations and experimental data showed that the proposed theoretical method was able to predict the lateral stiffness of the infilled CFS walls accurately.
- 10 May 2024
- Published by Elsevier in Thin-Walled Structures
- Vol. 201
Numerical study on the seismic performance of phosphogypsum-filled cold-formed thin-walled steel composite walls
- 10 May 2024
- Published by Elsevier in Thin-Walled Structures
- Vol. 201
Numerical study on the seismic performance of phosphogypsum-filled cold-formed thin-walled steel composite walls
- Open Access
- 27 February 2024
- Published by Science Research Academic Press in Advances in Computer and Engineering Technology Research
- Vol. 1 (2) , 432-440
Research on the Indoor Thermal Environment of Several Traditional Chinese Residential Buildings
To study the indoor thermal environment characteristics and influencing factors of traditional Chinese residential buildings, the existing research studies on the indoor thermal environment of traditional residential buildings were collected and organized, and the relevant measured data was extracted using GetDate software. After data analysis, the construction characteristics of brick and wood structures, wood structures, and raw soil structures were summarized. The indoor and outdoor temperature changes of the residential buildings in summer and winter were revealed. Finally, the indoor thermal environment characteristics and influencing factors of three types of traditional residential buildings were summarized. The research results can provide a reference for the construction and low-carbon renovation of traditional residential buildings.
- 27 February 2024
- Published by Science Research Academic Press in Advances in Computer and Engineering Technology Research
- Vol. 1 (2) , 432-440
Open AccessResearch on the Indoor Thermal Environment of Several Traditional Chinese Residential Buildings
To study the indoor thermal environment characteristics and influencing factors of traditional Chinese residential buildings, the existing research studies on the indoor thermal environment of traditional residential buildings were collected and organized, and the relevant measured data was extracted using GetDate software. After data analysis, the construction characteristics of brick and wood structures, wood structures, and raw soil structures were summarized. The indoor and outdoor temperature changes of the residential buildings in summer and winter were revealed. Finally, the indoor thermal environment characteristics and influencing factors of three types of traditional residential buildings were summarized. The research results can provide a reference for the construction and low-carbon renovation of traditional residential buildings.