Karl O. Albrecht
Research Subjects
Karl O. Albrecht has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Juan A. Lopez-Ruiz
Institute for Integrated Catalysis, Energy and Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Blvd., Richland, WA 99352, USA
4 shared publications Richard T. Hallen
Chemical and Biological Processes Development Group, Pacific Northwest National Laboratory, P.O. Box 999, Richland, Washington 99352, United States
4 shared publicationsAlan R. Cooper
Energy and Environment Directorate, Institute for Integrated Catalysis, Pacific Northwest National Laboratory, 902 Battelle Blvd., Richland, Washington 99352, United States
3 shared publicationsAndrew J. Schmidt
Chemical and Biological Processes Development Group, Pacific Northwest National Laboratory, P.O. Box 999, Richland, Washington 99352, United States
3 shared publications- Justin M. Billing
Pacific Northwest National Lab. (PNNL), Richland, WA (United States)
3 shared publications - Robert A. Dagle
Pacific Northwest National Laboratory (PNNL), Richland, WA (United States)
3 shared publications
Latest Publications
- Open Access
- 30 April 2026
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 148 (18) , 18746-18761
Catalyst Potential Prescribes Intermediate Coverages in Thermocatalytic Gluconic Acid Oxidation on Pt Nanoparticles
Thermocatalytic aqueous aerobic oxidation reactions occur as kinetically coupled processes that resemble two electrocatalytic half-reactions operating at open circuit. We leverage this concept to reveal a single set of elementary steps that describe not only the fundamental relationships between steady-state rates but also catalyst electrode potentials at open circuit (Ecat) during reactions among gluconic acid (GNA) and O2 on Pt surfaces at relevant conditions (0.03–0.95 M GNA, 20–2800 kPa O2, 333–363 K). Irreversible O2 reduction and GNA oxidation half-reactions couple via cycles that produce and consume surface hydroxyl moieties (HO*) on Pt sites, with kinetically relevant C–H bond scission that proceeds through heterolytic transition states (e.g., [*–O(H)···H+···C(H)(C5H9O6)-O(H)*]⧧). Observed turnover rates depend sensitively on the fractional coverages of both the O2- and GNA-derived intermediates. In situ measurements of Ecat provide needed mechanistic insight because these values appear uniquely sensitive to HO* coverages, which increase monotonically with increasing molar ratios of O2 to GNA. Notably, Ecat does not vary with the coverage of other surface intermediates. Intermittent exclusion of O2 from the reactor decreases Ecat to values below the point of zero charge (400 mVRHE) and, nonintuitively, yields increased reaction rates upon reintroduction of O2 due to the desorption of inhibiting GNA-derived carboxylate species. This strategy controls Ecat (and reactant coverages) in ways that increase reactor productivities by 50% or more when they are averaged over modulation cycles. These findings reveal the critical role of Ecat in setting the coverages of reactive intermediates and the ensuing impacts on rates during redox thermocatalysis.
- 30 April 2026
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 148 (18) , 18746-18761
Open AccessCatalyst Potential Prescribes Intermediate Coverages in Thermocatalytic Gluconic Acid Oxidation on Pt Nanoparticles
Thermocatalytic aqueous aerobic oxidation reactions occur as kinetically coupled processes that resemble two electrocatalytic half-reactions operating at open circuit. We leverage this concept to reveal a single set of elementary steps that describe not only the fundamental relationships between steady-state rates but also catalyst electrode potentials at open circuit (Ecat) during reactions among gluconic acid (GNA) and O2 on Pt surfaces at relevant conditions (0.03–0.95 M GNA, 20–2800 kPa O2, 333–363 K). Irreversible O2 reduction and GNA oxidation half-reactions couple via cycles that produce and consume surface hydroxyl moieties (HO*) on Pt sites, with kinetically relevant C–H bond scission that proceeds through heterolytic transition states (e.g., [*–O(H)···H+···C(H)(C5H9O6)-O(H)*]⧧). Observed turnover rates depend sensitively on the fractional coverages of both the O2- and GNA-derived intermediates. In situ measurements of Ecat provide needed mechanistic insight because these values appear uniquely sensitive to HO* coverages, which increase monotonically with increasing molar ratios of O2 to GNA. Notably, Ecat does not vary with the coverage of other surface intermediates. Intermittent exclusion of O2 from the reactor decreases Ecat to values below the point of zero charge (400 mVRHE) and, nonintuitively, yields increased reaction rates upon reintroduction of O2 due to the desorption of inhibiting GNA-derived carboxylate species. This strategy controls Ecat (and reactant coverages) in ways that increase reactor productivities by 50% or more when they are averaged over modulation cycles. These findings reveal the critical role of Ecat in setting the coverages of reactive intermediates and the ensuing impacts on rates during redox thermocatalysis.
- Open Access
- 16 July 2025
- Published by American Chemical Society (ACS) in ACS Catalysis
- p. 13015-13029
Surface Coverage Analysis Reveals Potential-Determining Heterolytic Reactions during Thermocatalytic Aerobic Glucose Oxidation
- 16 July 2025
- Published by American Chemical Society (ACS) in ACS Catalysis
- p. 13015-13029
Open AccessSurface Coverage Analysis Reveals Potential-Determining Heterolytic Reactions during Thermocatalytic Aerobic Glucose Oxidation
- 29 July 2020
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 34 (10) , 12556-12572
Methodology for the Development of Empirical Models Relating 13C NMR Spectral Features to Fuel Properties
- 29 July 2020
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 34 (10) , 12556-12572
Methodology for the Development of Empirical Models Relating 13C NMR Spectral Features to Fuel Properties
- 13 November 2019
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 7 (24) , 19889-19901
Strategies To Valorize the Hydrothermal Liquefaction-Derived Aqueous Phase into Fuels and Chemicals
- 13 November 2019
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 7 (24) , 19889-19901
Strategies To Valorize the Hydrothermal Liquefaction-Derived Aqueous Phase into Fuels and Chemicals
- Open Access
Cleanup and Conversion of Biomass Liquefaction Aqueous Phase to C3–C5 Olefins over ZnxZryOz Catalyst
The viability of using a ZnxZryOz mixed oxide catalyst for the direct production of C4 olefins from the aqueous phase derived from three different bio-oils was explored. The aqueous phases derived from (i) hydrothermal liquefaction of corn stover, (ii) fluidized bed fast pyrolysis of horse litter, and (iii) screw pyrolysis of wood pellets were evaluated as feedstocks. While exact compositions vary, the primary constituents for each feedstock are acetic acid and propionic acid. Continuous processing, based on liquid–liquid extraction, for the cleanup of the inorganic contaminants contained in the aqueous phase was also demonstrated. Complete conversion of the carboxylic acids was achieved over ZnxZryOz catalyst for all the feedstocks investigated. The main reaction products from each of the feedstocks include isobutene (>30% selectivity) and CO2 (>23% selectivity). Activity loss from coking was also observed, thereby rendering deactivation of the ZnxZryOz catalyst, however, complete recovery of catalyst activity was observed following regeneration. Finally, the presence of H2 in the feed was found to facilitate hydrogenation of intermediate acetone, thereby increasing propene production and, consequently, decreasing isobutene production.
Open AccessCleanup and Conversion of Biomass Liquefaction Aqueous Phase to C3–C5 Olefins over ZnxZryOz Catalyst
The viability of using a ZnxZryOz mixed oxide catalyst for the direct production of C4 olefins from the aqueous phase derived from three different bio-oils was explored. The aqueous phases derived from (i) hydrothermal liquefaction of corn stover, (ii) fluidized bed fast pyrolysis of horse litter, and (iii) screw pyrolysis of wood pellets were evaluated as feedstocks. While exact compositions vary, the primary constituents for each feedstock are acetic acid and propionic acid. Continuous processing, based on liquid–liquid extraction, for the cleanup of the inorganic contaminants contained in the aqueous phase was also demonstrated. Complete conversion of the carboxylic acids was achieved over ZnxZryOz catalyst for all the feedstocks investigated. The main reaction products from each of the feedstocks include isobutene (>30% selectivity) and CO2 (>23% selectivity). Activity loss from coking was also observed, thereby rendering deactivation of the ZnxZryOz catalyst, however, complete recovery of catalyst activity was observed following regeneration. Finally, the presence of H2 in the feed was found to facilitate hydrogenation of intermediate acetone, thereby increasing propene production and, consequently, decreasing isobutene production.
- 5 February 2019
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 9 (5) , 1117-1131
Oligomerization of ethanol-derived propene and isobutene mixtures to transportation fuels: catalyst and process considerations
In this paper, we report on solid acid catalysts and process conditions suitable for oligomerization of ethanol-derived mixed olefins propene and isobutene to transportation fuels, specifically targeting high-octane gasoline or jet-range hydrocarbons with high carbon efficiency. Catalytic performance was evaluated for two classes of solid acid catalysts—zeolites (H-ZSM-5, H-Y, H-beta) and polymeric resins (Amberlyst-36, Purolite-CT275)—each of which offer different catalytic properties. Two representative model olefin feeds: 1) diisobutene and 2) isobutene/propene (4/1 mol) mixture were used. Interestingly, both classes of solid acid catalysts can be tuned to produce a similar jet-distillate range hydrocarbon product with temperature determined to be the critical operating process parameter. For example, the propene conversion over H-beta zeolite was dramatically increased from 7 to 87% when the temperature was increased from 140 to 200 °C; whereas, nearly all (>99%) of the isobutene was converted over the same temperature range. However, with this relatively modest temperature increment (60 °C), formation of products in the jet-distillate range dramatically decreased from 90 to 65%, thus revealing an important activity/selectivity trade-off associated with the reaction temperature. Processing of aqueous ethanol to liquid hydrocarbon product was demonstrated in two sequential catalytic steps: 1) conversion of ethanol to an isobutene/propene-rich gas mixture over Zn1Zr2.5Oz catalyst, followed by 2) oligomerization over solid acid resin (Amberlyst-36). This processing sequence produced a highly branched olefin product primarily in the gasoline range (70% mass yield based on simulated distillation) with a high octane rating (approximate research octane number [RON] of 103). To increase the carbon yield to that of jet-range hydrocarbons, separation of the olefins from the light gases (i.e., H2, CO2, etc.) is required prior to oligomerization. Thus, in a separate set of experiments, an isobutene/propene mixture was converted over either H-beta (200 °C) or Purolite-CT275 (120 °C). This conversion step produced jet-range hydrocarbons with 80–85% mass yield. Upon subsequent distillation and hydrotreatment, both liquid products met select ASTM 7566 Annex A5 specifications for an alcohol-to-jet synthetic paraffinic kerosene (ATJ-SPK) blending component (e.g., specifications for freezing point, flash point, viscosity, and density).
- 5 February 2019
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 9 (5) , 1117-1131
Oligomerization of ethanol-derived propene and isobutene mixtures to transportation fuels: catalyst and process considerations
In this paper, we report on solid acid catalysts and process conditions suitable for oligomerization of ethanol-derived mixed olefins propene and isobutene to transportation fuels, specifically targeting high-octane gasoline or jet-range hydrocarbons with high carbon efficiency. Catalytic performance was evaluated for two classes of solid acid catalysts—zeolites (H-ZSM-5, H-Y, H-beta) and polymeric resins (Amberlyst-36, Purolite-CT275)—each of which offer different catalytic properties. Two representative model olefin feeds: 1) diisobutene and 2) isobutene/propene (4/1 mol) mixture were used. Interestingly, both classes of solid acid catalysts can be tuned to produce a similar jet-distillate range hydrocarbon product with temperature determined to be the critical operating process parameter. For example, the propene conversion over H-beta zeolite was dramatically increased from 7 to 87% when the temperature was increased from 140 to 200 °C; whereas, nearly all (>99%) of the isobutene was converted over the same temperature range. However, with this relatively modest temperature increment (60 °C), formation of products in the jet-distillate range dramatically decreased from 90 to 65%, thus revealing an important activity/selectivity trade-off associated with the reaction temperature. Processing of aqueous ethanol to liquid hydrocarbon product was demonstrated in two sequential catalytic steps: 1) conversion of ethanol to an isobutene/propene-rich gas mixture over Zn1Zr2.5Oz catalyst, followed by 2) oligomerization over solid acid resin (Amberlyst-36). This processing sequence produced a highly branched olefin product primarily in the gasoline range (70% mass yield based on simulated distillation) with a high octane rating (approximate research octane number [RON] of 103). To increase the carbon yield to that of jet-range hydrocarbons, separation of the olefins from the light gases (i.e., H2, CO2, etc.) is required prior to oligomerization. Thus, in a separate set of experiments, an isobutene/propene mixture was converted over either H-beta (200 °C) or Purolite-CT275 (120 °C). This conversion step produced jet-range hydrocarbons with 80–85% mass yield. Upon subsequent distillation and hydrotreatment, both liquid products met select ASTM 7566 Annex A5 specifications for an alcohol-to-jet synthetic paraffinic kerosene (ATJ-SPK) blending component (e.g., specifications for freezing point, flash point, viscosity, and density).
- 30 June 2018
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 32 (8) , 8483-8493
Assessment of Hydrotreatment for Hydrothermal Liquefaction Biocrudes from Sewage Sludge, Microalgae, and Pine Feedstocks
- 30 June 2018
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 32 (8) , 8483-8493
Assessment of Hydrotreatment for Hydrothermal Liquefaction Biocrudes from Sewage Sludge, Microalgae, and Pine Feedstocks
- 14 December 2017
- Published by American Chemical Society (ACS) in ACS Catalysis
- Vol. 8 (1) , 488-502
Aqueous-Phase Acetic Acid Ketonization over Monoclinic Zirconia
- 14 December 2017
- Published by American Chemical Society (ACS) in ACS Catalysis
- Vol. 8 (1) , 488-502
Aqueous-Phase Acetic Acid Ketonization over Monoclinic Zirconia
- 11 September 2017
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 5 (10) , 9136-9149
Steam Reforming of Acetic Acid over Co-Supported Catalysts: Coupling Ketonization for Greater Stability
- 11 September 2017
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 5 (10) , 9136-9149
Steam Reforming of Acetic Acid over Co-Supported Catalysts: Coupling Ketonization for Greater Stability