Martina Lingg
Research Subjects
Martina Lingg has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Ayodhya N. Tiwari
4 shared publications- Romain Carron
Laboratory for Thin Films and Photovoltaics Empa – Swiss Federal Laboratories for Materials Science and Technology Duebendorf Switzerland
4 shared publications - Stephan Buecheler
Laboratory for Thin Films and Photovoltaics, Empa—Swiss Federal Laboratories for Materials Science and Technology, Überlandstrasse 129, CH-8600 Dübendorf, Switzerland
4 shared publications Benjamin Bissig
2 shared publications- Carlos Guerra-Nuñez
Laboratory of Mechanics of Materials and Nanostructure, Empa, Swiss Federal Laboratories for Materials Science and Technology, Feuerwerkstrasse 39, CH-3602 Thun, Switzerland
2 shared publications Enrico Avancini
2 shared publications
Latest Publications
- Open Access
Review of CdTe1−xSex Thin Films in Solar Cell Applications
Recent improvements in CdTe thin film solar cells have been achieved by using CdTe1−xSex as a part of the absorber layer. This review summarizes the published literature concerning the material properties of CdTe1−xSex and its application in current thin film CdTe photovoltaics. One of the important properties of CdTe1−xSex is its band gap bowing, which facilitates a lowering of the CdTe band gap towards the optimum band gap for highest theoretical efficiency. In practice, a CdTe1−xSex gradient is introduced to the front of CdTe, which induces a band gap gradient and allows for the fabrication of solar cells with enhanced short-circuit current while maintaining a high open-circuit voltage. In some device structures, the addition of CdTe1−xSex also allows for a reduction in CdS thickness or its complete elimination, reducing parasitic absorption of low wavelength photons.
Open AccessReview of CdTe1−xSex Thin Films in Solar Cell Applications
Recent improvements in CdTe thin film solar cells have been achieved by using CdTe1−xSex as a part of the absorber layer. This review summarizes the published literature concerning the material properties of CdTe1−xSex and its application in current thin film CdTe photovoltaics. One of the important properties of CdTe1−xSex is its band gap bowing, which facilitates a lowering of the CdTe band gap towards the optimum band gap for highest theoretical efficiency. In practice, a CdTe1−xSex gradient is introduced to the front of CdTe, which induces a band gap gradient and allows for the fabrication of solar cells with enhanced short-circuit current while maintaining a high open-circuit voltage. In some device structures, the addition of CdTe1−xSex also allows for a reduction in CdS thickness or its complete elimination, reducing parasitic absorption of low wavelength photons.
- 1 January 2019
- Published by Elsevier in Thin Solid Films
- Vol. 669, 482-486
Bandgap of thin film solar cell absorbers: A comparison of various determination methods
- 1 January 2019
- Published by Elsevier in Thin Solid Films
- Vol. 669, 482-486
Bandgap of thin film solar cell absorbers: A comparison of various determination methods
- Open Access
- 1 October 2018
- Published by Taylor & Francis in Science and Technology of Advanced Materials
- Vol. 19 (1) , 683-692
Structural and electronic properties of CdTe1-xSex films and their application in solar cells
The performance improvement of conventional CdTe solar cells is mainly limited by doping concentration and minority carrier life time. Alloying CdTe with an isovalent element changes its properties, for example its band gap and behaviour of dopants, which has a significant impact on its performance as a solar cell absorber. In this work, the structural, optical, and electronic properties of CdTe1-xSex films are examined for different Se concentrations. The band gap of this compound changes with composition with a minimum of 1.40 eV for x = 0.3. We show that with increasing x, the lattice constant of CdTe1-xSex decreases, which can influence the solubility of dopants. We find that alloying CdTe with Se changes the effect of Cu doping on the p-type conductivity in CdTe1-xSex, reducing the achievable charge carrier concentration with increasing x. Using a front surface CdTe1-xSex layer, compositional, structural and electronic grading is introduced to solar cells. The efficiency is increased, mostly due to an increase in the short-circuit current density caused by a combination of lower band gap and a better interface between the absorber and window layer, despite a loss in the open-circuit voltage caused by the lower band gap and reduced charge carrier concentration. GRAPHICAL ABSTRACT
- 1 October 2018
- Published by Taylor & Francis in Science and Technology of Advanced Materials
- Vol. 19 (1) , 683-692
Open AccessStructural and electronic properties of CdTe1-xSex films and their application in solar cells
The performance improvement of conventional CdTe solar cells is mainly limited by doping concentration and minority carrier life time. Alloying CdTe with an isovalent element changes its properties, for example its band gap and behaviour of dopants, which has a significant impact on its performance as a solar cell absorber. In this work, the structural, optical, and electronic properties of CdTe1-xSex films are examined for different Se concentrations. The band gap of this compound changes with composition with a minimum of 1.40 eV for x = 0.3. We show that with increasing x, the lattice constant of CdTe1-xSex decreases, which can influence the solubility of dopants. We find that alloying CdTe with Se changes the effect of Cu doping on the p-type conductivity in CdTe1-xSex, reducing the achievable charge carrier concentration with increasing x. Using a front surface CdTe1-xSex layer, compositional, structural and electronic grading is introduced to solar cells. The efficiency is increased, mostly due to an increase in the short-circuit current density caused by a combination of lower band gap and a better interface between the absorber and window layer, despite a loss in the open-circuit voltage caused by the lower band gap and reduced charge carrier concentration. GRAPHICAL ABSTRACT
- 1 July 2017
- Published by Elsevier in Thin Solid Films
- Vol. 633, 218-221
On a better estimate of the charge collection function in CdTe solar cells: Al2O3 enhanced electron beam induced current measurements
- 1 July 2017
- Published by Elsevier in Thin Solid Films
- Vol. 633, 218-221
On a better estimate of the charge collection function in CdTe solar cells: Al2O3 enhanced electron beam induced current measurements
Surface Passivation for Reliable Measurement of Bulk Electronic Properties of Heterojunction Devices
Quantum efficiency measurements of state of the art Cu(In,Ga)Se2 (CIGS) thin film solar cells reveal current losses in the near infrared spectral region. These losses can be ascribed to inadequate optical absorption or poor collection of photogenerated charge carriers. Insight on the limiting mechanism is crucial for the development of more efficient devices. The electron beam induced current measurement technique applied on device cross-sections promises an experimental access to depth resolved information about the charge carrier collection probability. Here, this technique is used to show that charge carrier collection in CIGS deposited by multistage co-evaporation at low temperature is efficient over the optically active region and collection losses are minor as compared to the optical ones. Implications on the favorable absorber design are discussed. Furthermore, it is observed that the measurement is strongly affected by cross-section surface recombination and an accurate determination of the collection efficiency is not possible. Therefore it is proposed and shown that the use of an Al2O3 layer deposited onto the cleaved cross-section significantly improves the accuracy of the measurement by reducing the surface recombination. A model for the passivation mechanism is presented and the passivation concept is extended to other solar cell technologies such as CdTe and Cu2(Zn,Sn)(S,Se)4.
Surface Passivation for Reliable Measurement of Bulk Electronic Properties of Heterojunction Devices
Quantum efficiency measurements of state of the art Cu(In,Ga)Se2 (CIGS) thin film solar cells reveal current losses in the near infrared spectral region. These losses can be ascribed to inadequate optical absorption or poor collection of photogenerated charge carriers. Insight on the limiting mechanism is crucial for the development of more efficient devices. The electron beam induced current measurement technique applied on device cross-sections promises an experimental access to depth resolved information about the charge carrier collection probability. Here, this technique is used to show that charge carrier collection in CIGS deposited by multistage co-evaporation at low temperature is efficient over the optically active region and collection losses are minor as compared to the optical ones. Implications on the favorable absorber design are discussed. Furthermore, it is observed that the measurement is strongly affected by cross-section surface recombination and an accurate determination of the collection efficiency is not possible. Therefore it is proposed and shown that the use of an Al2O3 layer deposited onto the cleaved cross-section significantly improves the accuracy of the measurement by reducing the surface recombination. A model for the passivation mechanism is presented and the passivation concept is extended to other solar cell technologies such as CdTe and Cu2(Zn,Sn)(S,Se)4.
- Open Access
- 20 April 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (48) , 42069-42075
Sol gel and ceramic synthesis of Sr 2 FeMo 1−x W x O 6 (0 ≤ x ≤ 1) double perovskites series
Preparation methods (ceramic and sol–gel methods) using reducing conditions were optimized for the formation of phase pure double perovskites of Sr2FeMo(1−x)WxO6 (0 ≤ x ≤ 1) showing enhanced homogeneity and cation ordering for investigating magnetic properties. X-ray diffraction (XRD) revealed a structural transition from tetragonal to monoclinic as W replaces Mo (x = 0.5–0.6). The SQUID magnetometry confirmed a ferrimagnetic ground state for Sr2FeMoO6 whereas Sr2FeWO6 shows an antiferromagnetic state. Current results demonstrate that improved preparation methods can enhance the saturation magnetization.
- 20 April 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (48) , 42069-42075
Open AccessSol gel and ceramic synthesis of Sr 2 FeMo 1−x W x O 6 (0 ≤ x ≤ 1) double perovskites series
Preparation methods (ceramic and sol–gel methods) using reducing conditions were optimized for the formation of phase pure double perovskites of Sr2FeMo(1−x)WxO6 (0 ≤ x ≤ 1) showing enhanced homogeneity and cation ordering for investigating magnetic properties. X-ray diffraction (XRD) revealed a structural transition from tetragonal to monoclinic as W replaces Mo (x = 0.5–0.6). The SQUID magnetometry confirmed a ferrimagnetic ground state for Sr2FeMoO6 whereas Sr2FeWO6 shows an antiferromagnetic state. Current results demonstrate that improved preparation methods can enhance the saturation magnetization.