Min Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Min Sun has a total of 94 co-authors. Here are the top co-authors by number of shared publications:
Daniel Piedra
Department of Electrical Engineering and Computer Science, Massachusetts Institute of Technology, Cambridge, MA, United States of America
3 shared publications- Matteo Meneghini
University of Padova
2 shared publications Tomas Palacios
Microsystems Technology Laboratories, Massachusetts Institute of Technology, Cambridge, MA, USA
2 shared publications- Tomás Palacios
Microsystems Technology Laboratories, Massachusetts Institute of Technology 2 , Cambridge, Massachusetts 02139
2 shared publications Xiang Gao
IQE RF LLC, Somerset, NJ, USA
2 shared publications- Yuhao Zhang
The University of Hong Kong
2 shared publications
Latest Publications
- 18 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 11 (5) , 5078-5091
A Generalized Current Self-Sharing Strategy in Whole Operating Range for Series Capacitor Buck Converter
In high voltage step-down and high output current applications such as voltage regulator modules, electric vehicles, battery charger, series capacitor buck converter (SCBC) is a good choice but only in a limited duty cycle range. In this paper, a generalized current self-sharing strategy for the multi-phase SCBC is proposed, which have the ability of self-sharing current and uniform ultra-high step-down ratio in whole operating range. Through unified analysis of switching modes, the principles of charge-balance and volt-second balance are applied to achieve the self-sharing current and unified linear voltage step-down ratio. The master-slave phase-shift (Ms-Ps) modulation strategy for 4-phase SCBC is proposed to verify the proposed scheme, showing that the converter will have ultra-high 1/M-times voltage step-down and sensor-less current self-sharing over the full duty ratio range. Experiment results on 1.8V/20A hardware prototype is built to confirm the performance of the proposed strategy.
- 18 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 11 (5) , 5078-5091
A Generalized Current Self-Sharing Strategy in Whole Operating Range for Series Capacitor Buck Converter
In high voltage step-down and high output current applications such as voltage regulator modules, electric vehicles, battery charger, series capacitor buck converter (SCBC) is a good choice but only in a limited duty cycle range. In this paper, a generalized current self-sharing strategy for the multi-phase SCBC is proposed, which have the ability of self-sharing current and uniform ultra-high step-down ratio in whole operating range. Through unified analysis of switching modes, the principles of charge-balance and volt-second balance are applied to achieve the self-sharing current and unified linear voltage step-down ratio. The master-slave phase-shift (Ms-Ps) modulation strategy for 4-phase SCBC is proposed to verify the proposed scheme, showing that the converter will have ultra-high 1/M-times voltage step-down and sensor-less current self-sharing over the full duty ratio range. Experiment results on 1.8V/20A hardware prototype is built to confirm the performance of the proposed strategy.
- Open Access
- 26 March 2018
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 51 (16) , 163001
The 2018 GaN power electronics roadmap
- 26 March 2018
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 51 (16) , 163001
Open AccessThe 2018 GaN power electronics roadmap
- 4 July 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 64 (8) , 3126-3131
Instability of Dynamic- $R_{\text ON}$ and Threshold Voltage in GaN-on-GaN Vertical Field-Effect TransistorsThis paper investigates the recoverable degradation of GaN-on-GaN vertical transistors under positive gate bias stress. Based on combined pulsed measurements and constant voltage stress test, we demonstrate the following original results: 1) when subjected to moderate gate stress (0 V <; V GS <; 3 V), the devices show a negative threshold voltage shift, which is correlated with a decrease in on-resistance. This process is ascribed to the detrapping of electrons from the Al 2 O 3 insulator, induced by a low positive bias and 2) for high stress bias(V GS ≥ 5 V), a strong positive shift in threshold voltage is observed. This effect, which shows a slow recovery, is ascribed to the injection of electrons from the accumulation region (channel) toward the dielectric. Temperature-dependent measurements and 2-D simulations were carried out to support the hypothesis on degradation, and to evaluate the contribution of surface and bulk current in the n-GaN drift layer.
- 4 July 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 64 (8) , 3126-3131
Instability of Dynamic- $R_{\text ON}$ and Threshold Voltage in GaN-on-GaN Vertical Field-Effect TransistorsThis paper investigates the recoverable degradation of GaN-on-GaN vertical transistors under positive gate bias stress. Based on combined pulsed measurements and constant voltage stress test, we demonstrate the following original results: 1) when subjected to moderate gate stress (0 V <; V GS <; 3 V), the devices show a negative threshold voltage shift, which is correlated with a decrease in on-resistance. This process is ascribed to the detrapping of electrons from the Al 2 O 3 insulator, induced by a low positive bias and 2) for high stress bias(V GS ≥ 5 V), a strong positive shift in threshold voltage is observed. This effect, which shows a slow recovery, is ascribed to the injection of electrons from the accumulation region (channel) toward the dielectric. Temperature-dependent measurements and 2-D simulations were carried out to support the hypothesis on degradation, and to evaluate the contribution of surface and bulk current in the n-GaN drift layer.
- 27 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 38 (8) , 1097-1100
Vertical GaN Junction Barrier Schottky Rectifiers by Selective Ion Implantation
This letter demonstrates vertical GaN junction barrier Schottky (JBS) rectifiers fabricated with novel ion implantation techniques. We used two different methods to form the lateral p-n grids below the Schottky contact: 1) Mg implantation into n-GaN to form p-wells and 2) Si implantation into p-GaN to form n-wells. Specific differential ON-resistances (${R}_{ \mathrm{\scriptscriptstyle ON}}$ ) of 1.5–2.5$\text{m}\Omega ~\cdot $ cm 2 and 7–9$\text{m}\Omega ~\cdot $ cm 2 were obtained in the Mg-implanted and Si-implanted JBS rectifiers, respectively. A breakdown voltage of 500–600 V was achieved in both devices, with a leakage current at high reverse biases at least 100-fold lower than conventional vertical GaN Schottky barrier diodes. The impact of n-well and p-well widths on the${R}_{ \mathrm{\scriptscriptstyle ON}}$ and BV was investigated. Fast switching capability was also demonstrated. This letter shows the feasibility of forming patterned p-n junctions by novel ion implantation techniques, to enable high-performance vertical GaN power devices.- 27 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 38 (8) , 1097-1100
Vertical GaN Junction Barrier Schottky Rectifiers by Selective Ion Implantation
This letter demonstrates vertical GaN junction barrier Schottky (JBS) rectifiers fabricated with novel ion implantation techniques. We used two different methods to form the lateral p-n grids below the Schottky contact: 1) Mg implantation into n-GaN to form p-wells and 2) Si implantation into p-GaN to form n-wells. Specific differential ON-resistances (${R}_{ \mathrm{\scriptscriptstyle ON}}$ ) of 1.5–2.5$\text{m}\Omega ~\cdot $ cm 2 and 7–9$\text{m}\Omega ~\cdot $ cm 2 were obtained in the Mg-implanted and Si-implanted JBS rectifiers, respectively. A breakdown voltage of 500–600 V was achieved in both devices, with a leakage current at high reverse biases at least 100-fold lower than conventional vertical GaN Schottky barrier diodes. The impact of n-well and p-well widths on the${R}_{ \mathrm{\scriptscriptstyle ON}}$ and BV was investigated. Fast switching capability was also demonstrated. This letter shows the feasibility of forming patterned p-n junctions by novel ion implantation techniques, to enable high-performance vertical GaN power devices.- Top Cited PapersOpen Access
- 17 February 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 38 (4) , 509-512
High-Performance GaN Vertical Fin Power Transistors on Bulk GaN Substrates
This letter reports a GaN vertical fin power field-effect-transistor structure with submicron fin-shaped channels on bulk GaN substrates. In this vertical transistor design only n-GaN layers are needed, while no material regrowth or p-GaN layer is required. A combined dry/wet etch was used to get smooth fin vertical sidewalls. The fabricated transistor demonstrated a threshold voltage of 1 V and specific on resistance of 0.36 mΩcm 2 . By proper electric field engineering, 800 V blocking voltage was achieved at a gate bias of 0 V.
- 17 February 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 38 (4) , 509-512
Top Cited PapersOpen AccessHigh-Performance GaN Vertical Fin Power Transistors on Bulk GaN Substrates
This letter reports a GaN vertical fin power field-effect-transistor structure with submicron fin-shaped channels on bulk GaN substrates. In this vertical transistor design only n-GaN layers are needed, while no material regrowth or p-GaN layer is required. A combined dry/wet etch was used to get smooth fin vertical sidewalls. The fabricated transistor demonstrated a threshold voltage of 1 V and specific on resistance of 0.36 mΩcm 2 . By proper electric field engineering, 800 V blocking voltage was achieved at a gate bias of 0 V.
- Open Access
- 4 June 2012
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2012-02 (43) , 3239
Wafer-level Heterogeneous Integration of GaN HEMTs and Si (100) MOSFETs
- 4 June 2012
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2012-02 (43) , 3239
Open AccessWafer-level Heterogeneous Integration of GaN HEMTs and Si (100) MOSFETs
- 1 March 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 96 (10652221) , 169-172
Integration of a phase change material for junction-level cooling in GaN devices
Next generation gallium nitride (GaN) RF power transistors offer higher power, higher efficiency and wider bandwidth than competing Si technologies. However, the high power densities available in GaN power transistors create new challenges for heat dissipation. This paper presents a novel micro-scale thermal storage design that involves phase change material (PCM) filled grooves etched in the substrate to remove the heat generated in the active regions of a pulsed-mode GaN transistor. High electron mobility transistors (HEMTs) were fabricated on a GaN-on-Si wafer. Backside patterning and etching were done to thin the Si substrate under the active channel region of the selected transistors. A phase change material (PCM) with a melting temperature of 118°C was deposited in the etched grooves. Electrical measurements were carried out to compare the performance of transistors with and without PCM filled grooves. It was found that the groove etching did not degrade the transistor performance under low power conditions where the junction level heating is not enough to start the PCM melting process. From the current-voltage characteristics at different temperatures ranging from 25°C to 120°C, it was found that at higher temperatures, the current density in the PCM-enabled device was larger than in the reference device, due to the enhanced thermal management. The role of PCM was confirmed when measurements at temperatures well above the melting temperature of the PCM did not show signs of increase in the current density. The maximum current density in the device with PCM material was found to be much more stable under pulsed conditions than in current state-of-the-art devices.
- 1 March 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 96 (10652221) , 169-172
Integration of a phase change material for junction-level cooling in GaN devices
Next generation gallium nitride (GaN) RF power transistors offer higher power, higher efficiency and wider bandwidth than competing Si technologies. However, the high power densities available in GaN power transistors create new challenges for heat dissipation. This paper presents a novel micro-scale thermal storage design that involves phase change material (PCM) filled grooves etched in the substrate to remove the heat generated in the active regions of a pulsed-mode GaN transistor. High electron mobility transistors (HEMTs) were fabricated on a GaN-on-Si wafer. Backside patterning and etching were done to thin the Si substrate under the active channel region of the selected transistors. A phase change material (PCM) with a melting temperature of 118°C was deposited in the etched grooves. Electrical measurements were carried out to compare the performance of transistors with and without PCM filled grooves. It was found that the groove etching did not degrade the transistor performance under low power conditions where the junction level heating is not enough to start the PCM melting process. From the current-voltage characteristics at different temperatures ranging from 25°C to 120°C, it was found that at higher temperatures, the current density in the PCM-enabled device was larger than in the reference device, due to the enhanced thermal management. The role of PCM was confirmed when measurements at temperatures well above the melting temperature of the PCM did not show signs of increase in the current density. The maximum current density in the device with PCM material was found to be much more stable under pulsed conditions than in current state-of-the-art devices.