Jacek Boguski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jacek Boguski has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- Jarosław Wróbel
Institute of Applied Physics, Military University of Technology, Warsaw, Poland
10 shared publications - Sebastian Zlotnik
Institute of Applied Physics, Military University of Technology, gen. Sylwestra Kaliskiego 2, 00-908 Warsaw, Poland
6 shared publications - Piotr Martyniuk
Institute of Applied Physics, Military University of Technology, 2 Kaliskiego St., 00-908 Warsaw, Poland
5 shared publications - Jerzy Wrobel
Institute of Physics Polish Academy of Sciences, Aleja Lotników 32/46, PL-02-668 Warsaw, Poland
4 shared publications - Antoni Rogalski
Institute of Applied Physics, Military University of Technology, Warsaw, Poland
3 shared publications - Grażyna Przybytniak
Institute of Nuclear Chemistry and Technology, Warsaw, Poland
3 shared publications
Latest Publications
- 3 February 2026
- Published by Elsevier in Measurement
- Vol. 269
Evaluation of bulk and contact noise components with the Transfer Length Method: Model and experiment
- 3 February 2026
- Published by Elsevier in Measurement
- Vol. 269
Evaluation of bulk and contact noise components with the Transfer Length Method: Model and experiment
- Open Access
- 2 May 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (17)
Ionic liquid as a novel surface passivation for InAs/InAsSb type-II superlattice infrared detector
This research paper reports a novel approach to the passivation of InAs/InAsSb type-II superlattice mesa structures, using a hydrophobic ionic liquid 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [hmim][NTf2]. The most important advantages of ionic liquids are low vapor pressure, chemical resistance in a wide temperature range, and a simple procedure of applying to semiconductor structures. In the proposed technology, the ionic liquid is directly applied to a detector mesa after the metallization process. The measurements of dark current density–voltage characteristics of detector mesa structures reveal that the [hmim][NTf2] ionic liquid serves as passivator. The dark current density after passivation decreases and does not increase even after accelerated aging performed by heating samples for 24 h at 80 °C in air. Scanning electron microscope imaging, in turn, reveals that the hydrophobic ionic liquid forms a thin layer of several dozen nanometers on the surface of the detector mesa and does not cause short circuits. The ionic liquid also protects the device against atmospheric conditions; therefore, there is no need to create an encapsulating layer additionally protecting the slope of the detector mesa.
- 2 May 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (17)
Open AccessIonic liquid as a novel surface passivation for InAs/InAsSb type-II superlattice infrared detector
This research paper reports a novel approach to the passivation of InAs/InAsSb type-II superlattice mesa structures, using a hydrophobic ionic liquid 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [hmim][NTf2]. The most important advantages of ionic liquids are low vapor pressure, chemical resistance in a wide temperature range, and a simple procedure of applying to semiconductor structures. In the proposed technology, the ionic liquid is directly applied to a detector mesa after the metallization process. The measurements of dark current density–voltage characteristics of detector mesa structures reveal that the [hmim][NTf2] ionic liquid serves as passivator. The dark current density after passivation decreases and does not increase even after accelerated aging performed by heating samples for 24 h at 80 °C in air. Scanning electron microscope imaging, in turn, reveals that the hydrophobic ionic liquid forms a thin layer of several dozen nanometers on the surface of the detector mesa and does not cause short circuits. The ionic liquid also protects the device against atmospheric conditions; therefore, there is no need to create an encapsulating layer additionally protecting the slope of the detector mesa.
- Open Access
- 24 February 2023
- Published by Polish Academy of Sciences Chancellery in Opto-Electronics Review
- Vol. 31, 144564
Multi-technique characterisation of InAs-on-GaAs wafers with circular defect pattern
The article presents the results of diameter mapping for circular-symmetric disturbance of homogeneity of epitaxially grown InAs (100) layers on GaAs substrates. The set of acceptors (beryllium) doped InAs epilayers was studied in order to evaluate the impact of Be doping on the 2-inch InAs-on-GaAs wafers quality. During the initial identification of size and shape of the circular pattern, non-destructive optical techniques were used, showing a 100% difference in average roughness between the wafer centre and its outer part. On the other hand, no volumetric (bulk) differences are detectable using Raman spectroscopy and high-resolution X-ray diffraction. The correlation between Be doping level and circular defect pattern surface area has been found.
- 24 February 2023
- Published by Polish Academy of Sciences Chancellery in Opto-Electronics Review
- Vol. 31, 144564
Open AccessMulti-technique characterisation of InAs-on-GaAs wafers with circular defect pattern
The article presents the results of diameter mapping for circular-symmetric disturbance of homogeneity of epitaxially grown InAs (100) layers on GaAs substrates. The set of acceptors (beryllium) doped InAs epilayers was studied in order to evaluate the impact of Be doping on the 2-inch InAs-on-GaAs wafers quality. During the initial identification of size and shape of the circular pattern, non-destructive optical techniques were used, showing a 100% difference in average roughness between the wafer centre and its outer part. On the other hand, no volumetric (bulk) differences are detectable using Raman spectroscopy and high-resolution X-ray diffraction. The correlation between Be doping level and circular defect pattern surface area has been found.
- Open Access
- 24 February 2023
- Published by Polish Academy of Sciences Chancellery in Opto-Electronics Review
- Vol. 31, 144567
InAs light-to-heavy hole effective mass ratio determined experimentally from mobility spectrum analysis
Careful selection of the physical model of the material for a specific doping and selected operating temperatures is a non-trivial task. In numerical simulations that optimize practical devices such as detectors or lasers architecture, this challenge can be very difficult. However, even for such a well-known material as a 5 µm thick layer of indium arsenide on a semi-insulating gallium arsenide substrate, choosing a realistic set of band structure parameters for valence bands is remarkable. Here, the authors test the applicability range of various models of the valence band geometry, using a series of InAs samples with varying levels of p-type doping. Carefully prepared and pretested the van der Pauw geometry samples have been used for magneto-transport data acquisition in the 20–300 K temperature range and magnetic fields up to ±15 T, combined with a mobility spectra analysis. It was shown that in a degenerate statistic regime, temperature trends of mobility for heavy- and light-holes are uncorrelated. It has also been shown that parameters of the valence band effective masses with warping effect inclusion should be used for selected acceptor dopant levels and range of temperatures.
- 24 February 2023
- Published by Polish Academy of Sciences Chancellery in Opto-Electronics Review
- Vol. 31, 144567
Open AccessInAs light-to-heavy hole effective mass ratio determined experimentally from mobility spectrum analysis
Careful selection of the physical model of the material for a specific doping and selected operating temperatures is a non-trivial task. In numerical simulations that optimize practical devices such as detectors or lasers architecture, this challenge can be very difficult. However, even for such a well-known material as a 5 µm thick layer of indium arsenide on a semi-insulating gallium arsenide substrate, choosing a realistic set of band structure parameters for valence bands is remarkable. Here, the authors test the applicability range of various models of the valence band geometry, using a series of InAs samples with varying levels of p-type doping. Carefully prepared and pretested the van der Pauw geometry samples have been used for magneto-transport data acquisition in the 20–300 K temperature range and magnetic fields up to ±15 T, combined with a mobility spectra analysis. It was shown that in a degenerate statistic regime, temperature trends of mobility for heavy- and light-holes are uncorrelated. It has also been shown that parameters of the valence band effective masses with warping effect inclusion should be used for selected acceptor dopant levels and range of temperatures.
- Open Access
- 5 July 2022
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 16 (8)
Experimental Verification of Single‐Type Electron Population in Indium Tin Oxide Layers
Accurate determination of electronic transport properties of individual transparent conductive oxide layers, namely indium tin oxide (ITO), is essential for further development and design of photonic devices with ITO layer as a tunable ultrafast optoelectronic component. Precise magnetotransport measurements are here implemented to achieve carrier mobility distribution that gives insight into types and characteristics of carrier species. ITO thin films with various sheet resistance of ≈10, 75, and 350 Ω sq−1, respectively, are examined at near‐room temperature. Unimodal mobility distribution is revealed in ITO films, independently on their resistivity, with no evidence of unseparated contributions from surface or interface states. The electron mobility varies depending on ITO's resistivity, ranging from 36.8 to 47.2 cm2 V−1 s−1 at 300 K. Importantly, no minority hole conduction is present. The ITO thin films exhibit solely bulk‐like conduction with an absence of parallel conductions. In addition, the existence of single‐type electron population in ITO that can be viewed as an important validation of exclusively donor‐type defects and/or impurities contributing to total ITO conductivity is experimentally confirmed. These results indicate that ITO can be viewed as an integrated counterpart for photonic metadevices.
- 5 July 2022
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 16 (8)
Open AccessExperimental Verification of Single‐Type Electron Population in Indium Tin Oxide Layers
Accurate determination of electronic transport properties of individual transparent conductive oxide layers, namely indium tin oxide (ITO), is essential for further development and design of photonic devices with ITO layer as a tunable ultrafast optoelectronic component. Precise magnetotransport measurements are here implemented to achieve carrier mobility distribution that gives insight into types and characteristics of carrier species. ITO thin films with various sheet resistance of ≈10, 75, and 350 Ω sq−1, respectively, are examined at near‐room temperature. Unimodal mobility distribution is revealed in ITO films, independently on their resistivity, with no evidence of unseparated contributions from surface or interface states. The electron mobility varies depending on ITO's resistivity, ranging from 36.8 to 47.2 cm2 V−1 s−1 at 300 K. Importantly, no minority hole conduction is present. The ITO thin films exhibit solely bulk‐like conduction with an absence of parallel conductions. In addition, the existence of single‐type electron population in ITO that can be viewed as an important validation of exclusively donor‐type defects and/or impurities contributing to total ITO conductivity is experimentally confirmed. These results indicate that ITO can be viewed as an integrated counterpart for photonic metadevices.
- 4 February 2022
- Published by Wydawnictwo SIGMA-NOT, sp. z.o.o. in PRZEGLĄD ELEKTROTECHNICZNY
- Vol. 1 (2) , 146-149
Badanie wpływu wybranych parametrów cyklicznego procesu mokrego trawienia chemicznego epitaksjalnych warstw InAs
W niniejszym artykule poświęcono uwagę procesowi mokrego trawienia chemicznego warstw epitaksjalnych InAs. Do procesu wprowadzono modyfikację, polegającą na wykonaniu trawienia w sposób cykliczny, przy założonych całkowitych czasach procesu. Zbadano wpływ ilości cykli w procesie mokrego trawienia chemicznego na głębokość trawienia oraz chropowatość strawionej warstwy.
- 4 February 2022
- Published by Wydawnictwo SIGMA-NOT, sp. z.o.o. in PRZEGLĄD ELEKTROTECHNICZNY
- Vol. 1 (2) , 146-149
Badanie wpływu wybranych parametrów cyklicznego procesu mokrego trawienia chemicznego epitaksjalnych warstw InAs
W niniejszym artykule poświęcono uwagę procesowi mokrego trawienia chemicznego warstw epitaksjalnych InAs. Do procesu wprowadzono modyfikację, polegającą na wykonaniu trawienia w sposób cykliczny, przy założonych całkowitych czasach procesu. Zbadano wpływ ilości cykli w procesie mokrego trawienia chemicznego na głębokość trawienia oraz chropowatość strawionej warstwy.
- 1 January 2022
- Published by Wydawnictwo SIGMA-NOT, sp. z.o.o. in PRZEGLĄD ELEKTROTECHNICZNY
- Vol. 98 (9) , 228-230
Characterization of multi-channel charge carrier transport for epitaxial semiconductor structures
The paper highlights the need to develop techniques for the precise parameterization of multi-channel charge carrier transport, which are of fundamental importance for the effective design of semiconductor devices. The current state of development of these measurement techniques at the Military University of Technology is presented, as well as exemplary results for semiconductor structures obtained by molecular beam epitaxy (MBE).
- 1 January 2022
- Published by Wydawnictwo SIGMA-NOT, sp. z.o.o. in PRZEGLĄD ELEKTROTECHNICZNY
- Vol. 98 (9) , 228-230
Characterization of multi-channel charge carrier transport for epitaxial semiconductor structures
The paper highlights the need to develop techniques for the precise parameterization of multi-channel charge carrier transport, which are of fundamental importance for the effective design of semiconductor devices. The current state of development of these measurement techniques at the Military University of Technology is presented, as well as exemplary results for semiconductor structures obtained by molecular beam epitaxy (MBE).
- Open Access
Facile and Electrically Reliable Electroplated Gold Contacts to p-Type InAsSb Bulk-Like Epilayers
Narrow band-gap semiconductors, namely ternary InAsSb alloys, find substantial technological importance for mid-infrared application as photodetectors in medical diagnostics or environmental monitoring. Thus, it is crucial to develop electrical contacts for these materials because they are the fundamental blocks of all semiconductor devices. This study demonstrates that electroplated gold contacts can be considered as a simple and reliable metallization technology for the electrical-response examination of a test structure. Unalloyed electroplated Au contacts to InAsSb exhibit specific contact resistivity even lower than vacuum-deposited standard Ti–Au. Moreover, temperature-dependent transport properties, such as Hall carrier concentration and mobility, show similar trends, with a minor shift in the transition temperature. It can be associated with a difference in metallization technology, mainly the presence of a Ti interlayer in vacuum-deposited contacts. Such a transition may give insight into not only the gentle balance changes between conductivity channels but also an impression of changing the dominance of carrier type from p- to n-type. The magnetotransport experiments assisted with mobility spectrum analysis clearly show that such an interpretation is incorrect. InAsSb layers are strongly p-type dominant, with a clear contribution from valence band carriers observed at the whole analyzed temperature range. Furthermore, the presence of thermally activated band electrons is detected at temperatures higher than 220 K.
Open AccessFacile and Electrically Reliable Electroplated Gold Contacts to p-Type InAsSb Bulk-Like Epilayers
Narrow band-gap semiconductors, namely ternary InAsSb alloys, find substantial technological importance for mid-infrared application as photodetectors in medical diagnostics or environmental monitoring. Thus, it is crucial to develop electrical contacts for these materials because they are the fundamental blocks of all semiconductor devices. This study demonstrates that electroplated gold contacts can be considered as a simple and reliable metallization technology for the electrical-response examination of a test structure. Unalloyed electroplated Au contacts to InAsSb exhibit specific contact resistivity even lower than vacuum-deposited standard Ti–Au. Moreover, temperature-dependent transport properties, such as Hall carrier concentration and mobility, show similar trends, with a minor shift in the transition temperature. It can be associated with a difference in metallization technology, mainly the presence of a Ti interlayer in vacuum-deposited contacts. Such a transition may give insight into not only the gentle balance changes between conductivity channels but also an impression of changing the dominance of carrier type from p- to n-type. The magnetotransport experiments assisted with mobility spectrum analysis clearly show that such an interpretation is incorrect. InAsSb layers are strongly p-type dominant, with a clear contribution from valence band carriers observed at the whole analyzed temperature range. Furthermore, the presence of thermally activated band electrons is detected at temperatures higher than 220 K.
- Open Access
- 22 January 2020
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 14 (4)
Locally‐Strain‐Induced Heavy‐Hole‐Band Splitting Observed in Mobility Spectrum of p‐Type InAs Grown on GaAs
High‐quality Be‐doped InAs layer grown by molecular beam epitaxy on GaAs substrate has been examined via magnetotransport measurements and high‐resolution quantitative mobility spectrum analysis (HR‐QMSA) in the range of 5–300 K and up to 15 T magnetic field. The results show four‐channel conductivity and essential splitting of the most populated hole‐like channel below 55 K. It is concluded that origin of such effect results from the locally strain‐induced interlayer, which direct observation is difficult or impossible via alternative techniques. Based on the magnetotransport data analysis, the multilayer model is proposed, which is implemented into nextnano simulation, giving the proof of the argumentation correctness. These results indicate potential usefulness of HR‐QMSA technique even in the degeneration statistic regime.
- 22 January 2020
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 14 (4)
Open AccessLocally‐Strain‐Induced Heavy‐Hole‐Band Splitting Observed in Mobility Spectrum of p‐Type InAs Grown on GaAs
High‐quality Be‐doped InAs layer grown by molecular beam epitaxy on GaAs substrate has been examined via magnetotransport measurements and high‐resolution quantitative mobility spectrum analysis (HR‐QMSA) in the range of 5–300 K and up to 15 T magnetic field. The results show four‐channel conductivity and essential splitting of the most populated hole‐like channel below 55 K. It is concluded that origin of such effect results from the locally strain‐induced interlayer, which direct observation is difficult or impossible via alternative techniques. Based on the magnetotransport data analysis, the multilayer model is proposed, which is implemented into nextnano simulation, giving the proof of the argumentation correctness. These results indicate potential usefulness of HR‐QMSA technique even in the degeneration statistic regime.
- Open Access
- 5 July 2018
- Published by Springer Nature in Discover Nano
- Vol. 13 (1) , 196
Electrical Properties of Midwave and Longwave InAs/GaSb Superlattices Grown on GaAs Substrates by Molecular Beam Epitaxy
In the present work, we report on the in-plane electrical transport properties of midwave (MWIR) and longwave infrared (LWIR) InAs/GaSb type-II superlattices (T2SLs) grown by molecular beam epitaxy (MBE) system on GaAs (001) substrate. The huge lattice mismatch between the T2SL and GaAs substrate is reduced by the growth of GaSb buffer layer based on interfacial misfit array (IMF) technique. In order to compensate the strain in the InAs/GaSb T2SL, we utilized a special shutters sequence to get InSb-like and GaAs-like interfaces. It is found that the MWIR InAs/GaSb T2SL exhibits a p- and n-type conduction at low and high temperatures, respectively. Interestingly, the conduction change temperature is observed to be dependent on the growth temperature. On the other hand, LWIR T2SL conduction is dominated only by electrons. It is important to note that the dominant scattering mechanism in LWIR T2SL at low temperatures is the interface roughness scattering mechanism.
- 5 July 2018
- Published by Springer Nature in Discover Nano
- Vol. 13 (1) , 196
Open AccessElectrical Properties of Midwave and Longwave InAs/GaSb Superlattices Grown on GaAs Substrates by Molecular Beam Epitaxy
In the present work, we report on the in-plane electrical transport properties of midwave (MWIR) and longwave infrared (LWIR) InAs/GaSb type-II superlattices (T2SLs) grown by molecular beam epitaxy (MBE) system on GaAs (001) substrate. The huge lattice mismatch between the T2SL and GaAs substrate is reduced by the growth of GaSb buffer layer based on interfacial misfit array (IMF) technique. In order to compensate the strain in the InAs/GaSb T2SL, we utilized a special shutters sequence to get InSb-like and GaAs-like interfaces. It is found that the MWIR InAs/GaSb T2SL exhibits a p- and n-type conduction at low and high temperatures, respectively. Interestingly, the conduction change temperature is observed to be dependent on the growth temperature. On the other hand, LWIR T2SL conduction is dominated only by electrons. It is important to note that the dominant scattering mechanism in LWIR T2SL at low temperatures is the interface roughness scattering mechanism.