Rafal Anyszka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Rafal Anyszka has a total of 158 co-authors. Here are the top co-authors by number of shared publications:
Anke Blume
21 shared publications- Dariusz Mariusz Bieliński
Institute of Polymer and Dye Technology, Faculty of Chemistry, Lodz University of Technology, Stefanowskiego 16, 90-537 Lodz, Poland
17 shared publications Mika Paajanen
VTT Technical Research Centre of Finland,Tampere,Finland
17 shared publicationsWilma Dierkes
Faculty of Engineering Technology, Department of Mechanics of Solids, Surfaces & Systems (MS3), Chair of Elastomer Technology and Engineering, University of Twente, 7500 AE Enschede, The Netherlands
11 shared publications- Anke Blume
Department of Elastomer Technology and Engineering, University of Twente, Drienerlolaan 5, 7522 NB Enschede, The Netherlands
10 shared publications Eetta Saarimaki
VTT Technical Research Centre of Finland Ltd., Tampere, Finland
9 shared publications
Latest Publications
- Open Access
The Effect of Vulcanization Temperature on the Network Structure and Properties of TBAF-Functionalized BR/VMQ Blends for Mars Environment Applications
Rubber compounds intended for Mars exploration missions must remain elastic at extremely low temperatures while being manufactured in a reliable and energy-efficient manner. In this study, the effect of vulcanization temperature (100–160 °C) on the network structure and properties of butadiene/silicone rubber (BR/VMQ) blends was investigated, comparing a conventional sulfur curing system (REF) with the same system activated by fluoride anion obtained from tetra-n-butylammonium fluoride (TBAF). The fluoride anion acts as an in situ activator of elemental sulfur, through the opening of the S8 ring, facilitating the crosslinking process at significantly lower temperatures. Fluoride enabled rapid vulcanization at 100–120 °C, shortening the optimum cure time from 129.1 min to 61.4 min at 100 °C and from 36.7 min to 16.9 min at 120 °C. Equilibrium swelling and thiol-amine analysis revealed opposite structural responses to lowered curing temperature: the crosslink density of the reference compounds increased (from 1.25 × 10−4 to 1.56 × 10−4 mol/cm3 between 160 °C and 120 °C), whereas that of the TBAF-containing compounds decreased (from 1.32 × 10−4 to 0.60 × 10−4 mol/cm3 between 160 °C and 100 °C), yielding networks dominated by elastic polysulfidic crosslinks (up to 97.2%). We attribute this to a suppressed crosslink maturation under conditions of reduced thermal energy and shortened curing time. Low-temperature curing also suppressed the crystallization of the VMQ phase (melting enthalpy decreasing from 1.23 J/g to 0.21 J/g for TBAF compounds), which we hypothesize results from insufficient energy for phase separation and regular chain packing in this strongly immiscible blend. TBAF-cured compounds exhibited lower tanδ peaks, a stable tanδ plateau between approximately −60 °C and +20 °C, a tanδ-peak shift towards lower temperatures with decreasing curing temperature, and higher elongation at break and tensile strength at −40 °C. The results show that low-temperature, fluoride-activated vulcanization is a promising route for tailoring BR/VMQ networks towards stable dynamic performance across the Martian daily temperature range.
Open AccessThe Effect of Vulcanization Temperature on the Network Structure and Properties of TBAF-Functionalized BR/VMQ Blends for Mars Environment Applications
Rubber compounds intended for Mars exploration missions must remain elastic at extremely low temperatures while being manufactured in a reliable and energy-efficient manner. In this study, the effect of vulcanization temperature (100–160 °C) on the network structure and properties of butadiene/silicone rubber (BR/VMQ) blends was investigated, comparing a conventional sulfur curing system (REF) with the same system activated by fluoride anion obtained from tetra-n-butylammonium fluoride (TBAF). The fluoride anion acts as an in situ activator of elemental sulfur, through the opening of the S8 ring, facilitating the crosslinking process at significantly lower temperatures. Fluoride enabled rapid vulcanization at 100–120 °C, shortening the optimum cure time from 129.1 min to 61.4 min at 100 °C and from 36.7 min to 16.9 min at 120 °C. Equilibrium swelling and thiol-amine analysis revealed opposite structural responses to lowered curing temperature: the crosslink density of the reference compounds increased (from 1.25 × 10−4 to 1.56 × 10−4 mol/cm3 between 160 °C and 120 °C), whereas that of the TBAF-containing compounds decreased (from 1.32 × 10−4 to 0.60 × 10−4 mol/cm3 between 160 °C and 100 °C), yielding networks dominated by elastic polysulfidic crosslinks (up to 97.2%). We attribute this to a suppressed crosslink maturation under conditions of reduced thermal energy and shortened curing time. Low-temperature curing also suppressed the crystallization of the VMQ phase (melting enthalpy decreasing from 1.23 J/g to 0.21 J/g for TBAF compounds), which we hypothesize results from insufficient energy for phase separation and regular chain packing in this strongly immiscible blend. TBAF-cured compounds exhibited lower tanδ peaks, a stable tanδ plateau between approximately −60 °C and +20 °C, a tanδ-peak shift towards lower temperatures with decreasing curing temperature, and higher elongation at break and tensile strength at −40 °C. The results show that low-temperature, fluoride-activated vulcanization is a promising route for tailoring BR/VMQ networks towards stable dynamic performance across the Martian daily temperature range.
- Open Access
Closing Editorial to the Special Issue “Exploration and Innovation in Sustainable Rubber Performance”
It is with great pleasure that we present the collection of articles published in this Special Issue of MDPI’s Polymers, dedicated to “Exploration and Innovation in Sustainable Rubber Performance”
Open AccessClosing Editorial to the Special Issue “Exploration and Innovation in Sustainable Rubber Performance”
It is with great pleasure that we present the collection of articles published in this Special Issue of MDPI’s Polymers, dedicated to “Exploration and Innovation in Sustainable Rubber Performance”
- Open Access
- 10 October 2025
- Published by Elsevier in Radiation Physics and Chemistry
- Vol. 239
Ionizing radiation resistance of butadiene and silicone rubbers for Mars applications
- 10 October 2025
- Published by Elsevier in Radiation Physics and Chemistry
- Vol. 239
Open AccessIonizing radiation resistance of butadiene and silicone rubbers for Mars applications
- Open Access
- 15 July 2025
- Published by Elsevier in European Polymer Journal
- Vol. 236
Insight into the interactions of functionalised rubber-modified silica in tyre tread compounds
- 15 July 2025
- Published by Elsevier in European Polymer Journal
- Vol. 236
Open AccessInsight into the interactions of functionalised rubber-modified silica in tyre tread compounds
- Open Access
Improved Rubber Performance Through Phenolic Resin-Modified Silica: A Novel Coupling Mechanism for Enhanced Recyclability
Passenger car tires (PCTs) usually consist of a silica/silane-filled Butadiene Rubber (BR) or Solution Styrene Butadiene (SSBR) tread compound. This system is widely used due to improvements observed in rolling resistance (RR) as well as wet grip compared to carbon black-filled compounds. However, the covalent bond that couples silica via silane with the rubber increases the challenge of recycling these products. Furthermore, this strong covalent bond is unable to reform once it is broken, leading to a deterioration in tire properties. This work aims to improve these negative aspects of silica-filled compounds by developing a novel coupling system based on non-covalent interactions, which exhibit a reversible feature. The formation of this new coupling was accomplished by reacting silica with silane and a phenolic resin in order to obtain simultaneous π–π interactions and hydrogen bonding. The reaction was performed using two different silanes (amino and epoxy silane) and an alkyl phenol–formaldehyde resin. The implementation of the new coupling resulted in improved crosslink density, better mechanical performance, superior fatigue behavior, and a similar rolling resistance indicator.
Open AccessImproved Rubber Performance Through Phenolic Resin-Modified Silica: A Novel Coupling Mechanism for Enhanced Recyclability
Passenger car tires (PCTs) usually consist of a silica/silane-filled Butadiene Rubber (BR) or Solution Styrene Butadiene (SSBR) tread compound. This system is widely used due to improvements observed in rolling resistance (RR) as well as wet grip compared to carbon black-filled compounds. However, the covalent bond that couples silica via silane with the rubber increases the challenge of recycling these products. Furthermore, this strong covalent bond is unable to reform once it is broken, leading to a deterioration in tire properties. This work aims to improve these negative aspects of silica-filled compounds by developing a novel coupling system based on non-covalent interactions, which exhibit a reversible feature. The formation of this new coupling was accomplished by reacting silica with silane and a phenolic resin in order to obtain simultaneous π–π interactions and hydrogen bonding. The reaction was performed using two different silanes (amino and epoxy silane) and an alkyl phenol–formaldehyde resin. The implementation of the new coupling resulted in improved crosslink density, better mechanical performance, superior fatigue behavior, and a similar rolling resistance indicator.
- Open Access
- 27 February 2025
- Published by MDPI AG in Journal of Composites Science
- Vol. 9 (3) , 115
Toward Eco-Friendly Rubber: Utilizing Paper Waste-Derived Calcium Carbonate to Replace Carbon Black in Natural Rubber Composites
The growing concerns for the environmental impact of resource depletion and carbon emissions has led to the current study of using novel, sustainable materials in natural rubber compounds. The principal goal of this study was to reduce the usage of the non-renewable filler carbon black (CB). For this purpose, two waste-derived calcium carbonates were introduced in natural rubber compounds as a partial replacement for CB. To enhance their performance, the compounds were modified using alpha-lipoic acid and a titanate as in situ coupling agents. The effect of these renewable fillers and coupling agents on the in-rubber properties was analyzed using various characterization methods. Remarkably, by replacing 10 phr of carbon black with a calcium carbonate filler and introducing the alpha-lipoic acid coupling agent, a compound was obtained with performance levels similar to the CB-filled reference compound. These findings contribute valuable insights into the replacement of carbon black with renewable calcium carbonate fillers.
- 27 February 2025
- Published by MDPI AG in Journal of Composites Science
- Vol. 9 (3) , 115
Open AccessToward Eco-Friendly Rubber: Utilizing Paper Waste-Derived Calcium Carbonate to Replace Carbon Black in Natural Rubber Composites
The growing concerns for the environmental impact of resource depletion and carbon emissions has led to the current study of using novel, sustainable materials in natural rubber compounds. The principal goal of this study was to reduce the usage of the non-renewable filler carbon black (CB). For this purpose, two waste-derived calcium carbonates were introduced in natural rubber compounds as a partial replacement for CB. To enhance their performance, the compounds were modified using alpha-lipoic acid and a titanate as in situ coupling agents. The effect of these renewable fillers and coupling agents on the in-rubber properties was analyzed using various characterization methods. Remarkably, by replacing 10 phr of carbon black with a calcium carbonate filler and introducing the alpha-lipoic acid coupling agent, a compound was obtained with performance levels similar to the CB-filled reference compound. These findings contribute valuable insights into the replacement of carbon black with renewable calcium carbonate fillers.
- Open Access
- 15 January 2025
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 13 (8) , 3209-3221
Dynamic Imine Bonds in Tire Tread Compounds: A Pathway to a Circular Economy and Reduced Waste
- 15 January 2025
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 13 (8) , 3209-3221
Open AccessDynamic Imine Bonds in Tire Tread Compounds: A Pathway to a Circular Economy and Reduced Waste
- Open Access
- 11 January 2025
- Published by Elsevier in SSRN Electronic Journal
Interaction Aspects of Functionalised Styrene Butadiene Rubber-Modified Silica in Tyre Tread Compounds
- 11 January 2025
- Published by Elsevier in SSRN Electronic Journal
Open AccessInteraction Aspects of Functionalised Styrene Butadiene Rubber-Modified Silica in Tyre Tread Compounds
- 6 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Polypropylene Copolymers and Blends for HVDC Cable Insulation: Initial Characterization and Pilot-scale Production
This paper introduces a preliminary characterization of polypropylene-based copolymers as well as a possible ternary blend as a candidate to be used for HVDC cable insulation in the framework of the European project NEWGEN (New GENeration of HVDC insulating materials, cables and systems). The effect of production process scale-up (from mini-scale to pilot-scale cast-processing) is also investigated for the promising PP ternary blend which is essentially composed of homophasic PP random copolymer (RACO), heterophasic PP copolymer (HECO), and propylene-based elastomer (PBE). The preliminary dielectric characterization introduces a promising RACO/HECO/PBE blend with a similar and comparable performance of mini-scale and up-scaled specimens. Mechanical characterization show that incorporating HECO and PBE in the ternary blend reduces the stiffness metrics of RACO towards suitable values for HVDC cable applications.
- 6 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Polypropylene Copolymers and Blends for HVDC Cable Insulation: Initial Characterization and Pilot-scale Production
This paper introduces a preliminary characterization of polypropylene-based copolymers as well as a possible ternary blend as a candidate to be used for HVDC cable insulation in the framework of the European project NEWGEN (New GENeration of HVDC insulating materials, cables and systems). The effect of production process scale-up (from mini-scale to pilot-scale cast-processing) is also investigated for the promising PP ternary blend which is essentially composed of homophasic PP random copolymer (RACO), heterophasic PP copolymer (HECO), and propylene-based elastomer (PBE). The preliminary dielectric characterization introduces a promising RACO/HECO/PBE blend with a similar and comparable performance of mini-scale and up-scaled specimens. Mechanical characterization show that incorporating HECO and PBE in the ternary blend reduces the stiffness metrics of RACO towards suitable values for HVDC cable applications.
- Open Access
Effect of Butadiene Rubber Crystallization on Low-Temperature Properties of Butadiene/Silicone Rubber Blends with Potential for Mars Applications
This study explores the impact of butadiene rubber (BR) crystallization on the low-temperature properties of butadiene/silicone (VMQ) rubber blends (BR/VMQ) designed for Martian applications. Two types of BR, semi-crystalline high-cis Buna CB24 and amorphous Buna CB550, were blended with VMQ, and their mechanical and thermal properties were evaluated. Kinetics of vulcanization, static mechanical properties, dynamical mechanical analysis, thermal shrinkage, and differential scanning calorimetry were utilized. The research demonstrates that the semi-crystalline BR improves mechanical properties but induces greater shrinkage at low temperatures. Conversely, using amorphous BR provided more consistent mechanical properties across the Martian temperature range and reduced material shrink by 6.71% for samples with carbon black, by 8.36% for samples with silica, and by 11.63% for unfilled samples. Future research will be required to evaluate the impact of volume change on the sealing properties of the BR/VMQ blends.
Open AccessEffect of Butadiene Rubber Crystallization on Low-Temperature Properties of Butadiene/Silicone Rubber Blends with Potential for Mars Applications
This study explores the impact of butadiene rubber (BR) crystallization on the low-temperature properties of butadiene/silicone (VMQ) rubber blends (BR/VMQ) designed for Martian applications. Two types of BR, semi-crystalline high-cis Buna CB24 and amorphous Buna CB550, were blended with VMQ, and their mechanical and thermal properties were evaluated. Kinetics of vulcanization, static mechanical properties, dynamical mechanical analysis, thermal shrinkage, and differential scanning calorimetry were utilized. The research demonstrates that the semi-crystalline BR improves mechanical properties but induces greater shrinkage at low temperatures. Conversely, using amorphous BR provided more consistent mechanical properties across the Martian temperature range and reduced material shrink by 6.71% for samples with carbon black, by 8.36% for samples with silica, and by 11.63% for unfilled samples. Future research will be required to evaluate the impact of volume change on the sealing properties of the BR/VMQ blends.