Andrew J. Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Andrew J. Lee has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
Daniel J. Inman
Aerospace Engineering Department, University of Michigan, Ann Arbor, MI, USA
7 shared publicationsJuan M. Fernandez
NASA Langley Research Center
6 shared publicationsAmin Moosavian
University of Michigan
4 shared publications- Daniel J. Inman
Department of Aerospace Engineering, University of Michigan, Ann Arbor, USA
3 shared publications Jacob G. Daye
North Carolina State University
3 shared publications- Jacob G. Daye
Department of Mechanical and Aerospace Engineering, North Carolina State University, Raleigh, NC 27606, United States of America
3 shared publications
Latest Publications
- 24 May 2026
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 64 (10) , 1-13
Active Reduction of Dynamic Fold Propagation in Deployable Shell Structures
Ultrathin composite shell structures are capable of self-deployment by releasing stored strain energy accumulated in their elastic folds during stowage. However, uncontrolled deployment is susceptible to irregular motion, self-contact, or structural damage. To ensure a reliable unfolding sequence, this paper investigates the active reduction of an elastically propagating fold in a freely deploying thin-shell composite structure. A Macro Fiber Composite (MFC) piezoelectric actuator is bonded to a cantilevered composite tape spring near the fixed root. Through voltage-induced deformations, the MFC alters the transverse shell curvature to inhibit the motion of the propagating fold. The actuation effects on deployment are investigated both experimentally and with explicit finite element analysis. The two approaches characterize the unactuated, statically actuated, and dynamically actuated deployments for the composite tape spring with a single localized opposite-sense fold. Negative static actuation prolongs unfolding, while positive static and dynamic actuation lower the deployment duration in addition to attenuating the fold propagation dynamics.
- 24 May 2026
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 64 (10) , 1-13
Active Reduction of Dynamic Fold Propagation in Deployable Shell Structures
Ultrathin composite shell structures are capable of self-deployment by releasing stored strain energy accumulated in their elastic folds during stowage. However, uncontrolled deployment is susceptible to irregular motion, self-contact, or structural damage. To ensure a reliable unfolding sequence, this paper investigates the active reduction of an elastically propagating fold in a freely deploying thin-shell composite structure. A Macro Fiber Composite (MFC) piezoelectric actuator is bonded to a cantilevered composite tape spring near the fixed root. Through voltage-induced deformations, the MFC alters the transverse shell curvature to inhibit the motion of the propagating fold. The actuation effects on deployment are investigated both experimentally and with explicit finite element analysis. The two approaches characterize the unactuated, statically actuated, and dynamically actuated deployments for the composite tape spring with a single localized opposite-sense fold. Negative static actuation prolongs unfolding, while positive static and dynamic actuation lower the deployment duration in addition to attenuating the fold propagation dynamics.
- Open Access
- 22 April 2026
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 337
Nonlinear vibrations from local shell buckling in composite tape spring hinges
- 22 April 2026
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 337
Open AccessNonlinear vibrations from local shell buckling in composite tape spring hinges
- 13 April 2026
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
- Vol. 37 (15) , 887-901
Extension of cross-well bandwidths for bistable piezoelectric plate oscillators
Snap-through dynamics between the two potential wells of bistable oscillators are exhibited over a wide frequency range which narrows with decreasing harmonic excitation amplitudes until disappearing at a critical forcing level. However, for efficient conversion from vibrational to electrical energy in harvesting applications, the bistable oscillator must retain its favorable broadband cross-well response while the input excitation is minimized. To maintain effectiveness at low forcing levels, an actuation approach is proposed where external perturbations are used to extend the oscillator’s cross-well bandwidths by switching from co-existing low to high energy attractors. By utilizing Macro Fiber Composites (MFC) in a [ 0 MFC / 90 MFC ] T bistable piezoelectric laminate, the application of rectangular voltage pulse signals are cycled through different response phases to continuously alter the basins of attraction until the desired cross-well orbit is sustained at each frequency. The pulse magnitude is where the system exhibits limit point behavior and the resulting snap through actuation mechanism brings consistency between perturbation trials. A multi degree of freedom electromechanical model that captures the stable shapes and cross-well dynamics and finite element analysis in Abaqus/Standard demonstrate the efficacy of the perturbation method. The model is then employed to significantly increase the bandwidths inducing cross-well oscillations.
- 13 April 2026
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
- Vol. 37 (15) , 887-901
Extension of cross-well bandwidths for bistable piezoelectric plate oscillators
Snap-through dynamics between the two potential wells of bistable oscillators are exhibited over a wide frequency range which narrows with decreasing harmonic excitation amplitudes until disappearing at a critical forcing level. However, for efficient conversion from vibrational to electrical energy in harvesting applications, the bistable oscillator must retain its favorable broadband cross-well response while the input excitation is minimized. To maintain effectiveness at low forcing levels, an actuation approach is proposed where external perturbations are used to extend the oscillator’s cross-well bandwidths by switching from co-existing low to high energy attractors. By utilizing Macro Fiber Composites (MFC) in a [ 0 MFC / 90 MFC ] T bistable piezoelectric laminate, the application of rectangular voltage pulse signals are cycled through different response phases to continuously alter the basins of attraction until the desired cross-well orbit is sustained at each frequency. The pulse magnitude is where the system exhibits limit point behavior and the resulting snap through actuation mechanism brings consistency between perturbation trials. A multi degree of freedom electromechanical model that captures the stable shapes and cross-well dynamics and finite element analysis in Abaqus/Standard demonstrate the efficacy of the perturbation method. The model is then employed to significantly increase the bandwidths inducing cross-well oscillations.
- Open Access
- 1 March 2026
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 35 (3) , 035027
Optical sensing of deployment dynamics in composite shell structures with fiber Bragg gratings
The efficacy of using a fiber Bragg grating (FBG) optical sensor for characterizing the dynamic deployment behaviors of a bistable composite tape spring is investigated in this paper. Ultra-thin composite shells such as tape springs are favorable as spacecraft structures due to enabling the precise deployment of flexible solar arrays, solar sails, reflectors, and antennas. These composite members can elastically transition from either the coiled or folded state to the deployed extended state while possessing superior stiffness to mass ratios, thermal properties, and stowed compactness when compared to their metal counterparts. Bistability can induce more controllable self-deployment while mitigating the need for mechanical restraints or motorized deployment. However, a need exists to monitor both the deployment dynamics and overall structural health of the deployed structure. Fiber optic sensors such as FBGs have the capability to sense pressure, temperature, and mechanical strain. Due to their relative thinness, low mass, and flexibility, an optical fiber may be integrated into these deployable composite structures without significantly interfering with stability, packaging, or deployability. This paper experimentally demonstrates that an FBG sensor embedded in a bistable composite tape springs is effective at strain sensing the deployment dynamics. The freely deploying motion from coiled and folded configurations under stowage are characterized by linking tape spring displacements from a motion capture system to the FBG strains. From the equal sense coiled configuration, a rapid decrease from the nominal relative strain 0.034% to –0.001% indicates imminent deployment. In opposite sense unfolding configurations, a correlation is built between FBG strain peaks and longitudinal curvature such that the propagating fold and full deployment are fully captured by the single strain sensor.
- 1 March 2026
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 35 (3) , 035027
Open AccessOptical sensing of deployment dynamics in composite shell structures with fiber Bragg gratings
The efficacy of using a fiber Bragg grating (FBG) optical sensor for characterizing the dynamic deployment behaviors of a bistable composite tape spring is investigated in this paper. Ultra-thin composite shells such as tape springs are favorable as spacecraft structures due to enabling the precise deployment of flexible solar arrays, solar sails, reflectors, and antennas. These composite members can elastically transition from either the coiled or folded state to the deployed extended state while possessing superior stiffness to mass ratios, thermal properties, and stowed compactness when compared to their metal counterparts. Bistability can induce more controllable self-deployment while mitigating the need for mechanical restraints or motorized deployment. However, a need exists to monitor both the deployment dynamics and overall structural health of the deployed structure. Fiber optic sensors such as FBGs have the capability to sense pressure, temperature, and mechanical strain. Due to their relative thinness, low mass, and flexibility, an optical fiber may be integrated into these deployable composite structures without significantly interfering with stability, packaging, or deployability. This paper experimentally demonstrates that an FBG sensor embedded in a bistable composite tape springs is effective at strain sensing the deployment dynamics. The freely deploying motion from coiled and folded configurations under stowage are characterized by linking tape spring displacements from a motion capture system to the FBG strains. From the equal sense coiled configuration, a rapid decrease from the nominal relative strain 0.034% to –0.001% indicates imminent deployment. In opposite sense unfolding configurations, a correlation is built between FBG strain peaks and longitudinal curvature such that the propagating fold and full deployment are fully captured by the single strain sensor.
- Open Access
- 12 May 2025
- Published by Elsevier in Composite Structures
- Vol. 367
Deployment of bistable composite tape springs with non-uniform curvatures
- 12 May 2025
- Published by Elsevier in Composite Structures
- Vol. 367
Open AccessDeployment of bistable composite tape springs with non-uniform curvatures
- 1 March 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 62 (2) , 592-605
Structural Architectures for Imperfect Deployable Lunar Towers
The load-carrying performance for deployable lunar tower architectures using thin-ply composite booms is parametrically evaluated. These towers support a communications and sensor platform on the lunar surface. The primary design consists of the corrugated rollable tubular boom (COROTUB) acting as the primary tower mast that supports the payload tip mass. Guy wires connecting the boom tip to spreader bars attached at the base serve to correct lateral eccentricities and increase dimensional accuracy. The analysis compares the maximum tip mass that this primary design can carry relative to a reference design that does not contain any guy wires or spreader bars. The results provide insights into whether the additional system mass and complexity associated with the cable-stayed design are worth the increased payload mass that can be supported. By setting the design limiting condition to a maximum allowable deflection, the analysis reveals that the primary design has better performance when the spreader bar length relative to the tower height exceeds a critical value. The analysis is extended to lunar towers with collapsible tubular mast (CTM) booms, and similar trends are observed. Finally, the analytical load displacement behavior of the COROTUB and CTM reference towers is verified with finite element simulations.
- 1 March 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 62 (2) , 592-605
Structural Architectures for Imperfect Deployable Lunar Towers
The load-carrying performance for deployable lunar tower architectures using thin-ply composite booms is parametrically evaluated. These towers support a communications and sensor platform on the lunar surface. The primary design consists of the corrugated rollable tubular boom (COROTUB) acting as the primary tower mast that supports the payload tip mass. Guy wires connecting the boom tip to spreader bars attached at the base serve to correct lateral eccentricities and increase dimensional accuracy. The analysis compares the maximum tip mass that this primary design can carry relative to a reference design that does not contain any guy wires or spreader bars. The results provide insights into whether the additional system mass and complexity associated with the cable-stayed design are worth the increased payload mass that can be supported. By setting the design limiting condition to a maximum allowable deflection, the analysis reveals that the primary design has better performance when the spreader bar length relative to the tower height exceeds a critical value. The analysis is extended to lunar towers with collapsible tubular mast (CTM) booms, and similar trends are observed. Finally, the analytical load displacement behavior of the COROTUB and CTM reference towers is verified with finite element simulations.
- Open Access
- 27 January 2025
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 34 (2) , 025040
Uncoiling deployment of thin-shell composite booms with piezoelectric actuation
The efficacy of using piezoelectric actuators to initiate the dynamic deployment of bistable composite tape springs is evaluated in this paper. Ultra-thin composite booms such as tape springs and their cross-sectional variants have seen increased popularity in spacecraft structures due to enabling the precise deployment of flexible solar arrays, sails, reflectors, and antennas. They can elastically transition between the deployed ‘extended’ position and the stowed ‘coiled’ position while retaining superior stiffness, thermal properties, mass efficiency, and compactness when compared to thin-shelled metal booms and rigid articulated columns. Bistability in the coiled and extended states allows the boom to exhibit more controllable self-deployment and become reconfigurable, which could allow spacecraft to relocate, redeploy, and adapt to changing environmental conditions or mission objectives. Deployment systems commonly include motors and mechanical restraints that significantly contribute to mechanical complexity and spacecraft weight. Since bistable booms do not rely on elastic instability of packaging to initiate motion, a non-intrusive and lightweight actuation mechanism is needed to trigger deployment. This paper experimentally demonstrates how a macro fiber composite actuator can statically and dynamically excite a stowed composite tape spring to initiate unrolling into its extended state. A finite element model in Abaqus/Explicit is also developed to computationally corroborate the deployment schemes discussed.
- 27 January 2025
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 34 (2) , 025040
Open AccessUncoiling deployment of thin-shell composite booms with piezoelectric actuation
The efficacy of using piezoelectric actuators to initiate the dynamic deployment of bistable composite tape springs is evaluated in this paper. Ultra-thin composite booms such as tape springs and their cross-sectional variants have seen increased popularity in spacecraft structures due to enabling the precise deployment of flexible solar arrays, sails, reflectors, and antennas. They can elastically transition between the deployed ‘extended’ position and the stowed ‘coiled’ position while retaining superior stiffness, thermal properties, mass efficiency, and compactness when compared to thin-shelled metal booms and rigid articulated columns. Bistability in the coiled and extended states allows the boom to exhibit more controllable self-deployment and become reconfigurable, which could allow spacecraft to relocate, redeploy, and adapt to changing environmental conditions or mission objectives. Deployment systems commonly include motors and mechanical restraints that significantly contribute to mechanical complexity and spacecraft weight. Since bistable booms do not rely on elastic instability of packaging to initiate motion, a non-intrusive and lightweight actuation mechanism is needed to trigger deployment. This paper experimentally demonstrates how a macro fiber composite actuator can statically and dynamically excite a stowed composite tape spring to initiate unrolling into its extended state. A finite element model in Abaqus/Explicit is also developed to computationally corroborate the deployment schemes discussed.
- 1 May 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 61 (3) , 757-772
Bistable Deployable Composite Booms with Parabolic Cross Sections
The stable extended and coiled states of thin-shelled composite booms with parabolic cross sections are investigated in this paper. These conic shapes potentially offer greater stiffness properties when compared to circular cross sections, which is critical for improving the load-bearing performance of deployed booms. Inducing bistability through composite layups in parabolic booms would allow for controllable self-deployment due to a less energetic coiled state when compared to monostable booms. An inextensional analytical model is used to predict the stable coiled diameters of tape spring and collapsible tubular mast (CTM) booms with parabolic cross sections. The parabolic section is discretized into circular segments using biarc spline interpolation, which allows them to be integrated into the strain energy minimization procedure used to obtain the equilibrium states. When the parabolic booms are parametrically compared against circular booms with identical layups, flattened height, and mass, the former are found to generally have better stiffness performance while being less efficient in stowed volume, as evidenced by larger coiled diameters. Analytical coiled diameters and their strain energy are verified with finite element simulations for an optimal parabolic tape spring and CTM booms. Additional validation of the parabolic tape spring’s coiled diameter is provided by experimental measurements of boom specimens.
- 1 May 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 61 (3) , 757-772
Bistable Deployable Composite Booms with Parabolic Cross Sections
The stable extended and coiled states of thin-shelled composite booms with parabolic cross sections are investigated in this paper. These conic shapes potentially offer greater stiffness properties when compared to circular cross sections, which is critical for improving the load-bearing performance of deployed booms. Inducing bistability through composite layups in parabolic booms would allow for controllable self-deployment due to a less energetic coiled state when compared to monostable booms. An inextensional analytical model is used to predict the stable coiled diameters of tape spring and collapsible tubular mast (CTM) booms with parabolic cross sections. The parabolic section is discretized into circular segments using biarc spline interpolation, which allows them to be integrated into the strain energy minimization procedure used to obtain the equilibrium states. When the parabolic booms are parametrically compared against circular booms with identical layups, flattened height, and mass, the former are found to generally have better stiffness performance while being less efficient in stowed volume, as evidenced by larger coiled diameters. Analytical coiled diameters and their strain energy are verified with finite element simulations for an optimal parabolic tape spring and CTM booms. Additional validation of the parabolic tape spring’s coiled diameter is provided by experimental measurements of boom specimens.
- 28 July 2022
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 254-255
Mass efficiency of strip-based coilable space structures
- 28 July 2022
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 254-255
Mass efficiency of strip-based coilable space structures
- 3 January 2022
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Bistable Deployable Composite Booms With Parabolic Cross-Sections
View Video Presentation: https://doi.org/10.2514/6.2022-2264.vid This paper investigates how stable equilibrium states in the extended and coiled configurations can be predicted in thin-shelled composite booms with parabolic cross-sections. These conic shapes potentially offer greater stiffness properties when compared to circular cross-sections, which is critical for improving the load bearing performance of deployed booms. Inducing bistability through the choice of composite shell layups in parabolic booms would allow for controllable self-deployment due to a less energetic coiled state when compared to monostable booms. An inextensional analytical model is used to predict the stable coiled diameters of tape spring and Collapsible Tubular Mast (CTM) booms with parabolic cross-sections. The parabolic section is discretized into circular segments using biarc spline interpolation, which allows them to be integrated into the strain energy minimization procedure used to obtain the equilibrium states. When the parabolic booms are parametrically compared against circular booms with identical layups, flattened height, and mass, the former are found to generally have better stiffness performance while being less efficient in stowed volume as evidenced by larger coiled diameters. Analytical coiled diameters and their strain energy are verified with finite element simulations for optimal parabolic tape spring and CTM booms.
- 3 January 2022
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Bistable Deployable Composite Booms With Parabolic Cross-Sections
View Video Presentation: https://doi.org/10.2514/6.2022-2264.vid This paper investigates how stable equilibrium states in the extended and coiled configurations can be predicted in thin-shelled composite booms with parabolic cross-sections. These conic shapes potentially offer greater stiffness properties when compared to circular cross-sections, which is critical for improving the load bearing performance of deployed booms. Inducing bistability through the choice of composite shell layups in parabolic booms would allow for controllable self-deployment due to a less energetic coiled state when compared to monostable booms. An inextensional analytical model is used to predict the stable coiled diameters of tape spring and Collapsible Tubular Mast (CTM) booms with parabolic cross-sections. The parabolic section is discretized into circular segments using biarc spline interpolation, which allows them to be integrated into the strain energy minimization procedure used to obtain the equilibrium states. When the parabolic booms are parametrically compared against circular booms with identical layups, flattened height, and mass, the former are found to generally have better stiffness performance while being less efficient in stowed volume as evidenced by larger coiled diameters. Analytical coiled diameters and their strain energy are verified with finite element simulations for optimal parabolic tape spring and CTM booms.