Kunal B. Modi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kunal B. Modi has a total of 115 co-authors. Here are the top co-authors by number of shared publications:
- Nimish H. Vasoya
Department of Physics, Faculty of Science, M. S. University of Baroda, Vadodara 390002, India
9 shared publications - Pooja Y. Raval
Department of Physics, Saurashtra University, Rajkot, India
9 shared publications H. H. Joshi
Saurashtra University
5 shared publicationsK. B. Zankat
Government Science College, Sector 15, Gandhinagar 382016, India
5 shared publicationsNimish H. Vasoya
5 shared publicationsP. R. Pansara
Department of Physics, Saurashtra University, Rajkot 360005, India
5 shared publications
Latest Publications
- Open Access
- 10 June 2026
- Published by Elsevier in SSRN Electronic Journal
Cationic distribution, magnetic ordering, non-linear J-E characteristics, and sustainable gamma-ray shielding by Al3+ substituted CaCu3Ti4O12 quadruple perovskites
Herein, the influence of Al³⁺ substitution on the physical properties of quadruple perovskites, CaCu3-xAl2xTi4-xO12 (x = 0.0, 0.1, 0.3, 0.5), has been systematically investigated. Rietveld refinement of X-ray diffraction profiles confirms a strong preference of Al³⁺ ions for the octahedral (B-) site. Magnetic measurements M(T) (T = 5–300 K, H = 100 Oe) and M(H) (T = 5 K and 300 K, Hₘₐₓ = 70 kOe) reveal antiferromagnetic ordering at TN ≈ 25 K for the pristine sample. Upon Al³⁺ substitution, coexistence of antiferromagnetic, ferromagnetic, and paramagnetic phases is observed, with paramagnetism dominating at T ≫ TN. Soft ferromagnetic behaviour is evident at 300 K for x = 0.1–0.5 compositions. The nonlinear J–E characteristics at elevated temperatures (300–873 K) indicate switching behaviour, primarily attributed to Jahn–Teller distortion induced by Cu²⁺ ions. The maximum current density reaches 327 mA/cm² (x = 0.0) and increases to 429 mA/cm² for substituted samples (x = 0.1–0.5), representing exceptionally high reported values. Radiation shielding analysis shows enhanced linear and mass attenuation coefficients, along with higher fast neutron removal cross-sections, and reduced half-value and tenth-value layers compared to conventional gamma shielding materials in the 122–1330 keV range at 300 K. Radiation protection efficiency results indicate strong photon attenuation within ~122–511 keV. The variation of shielding parameters with incident photon energy is explained by three separate inelastic photon interaction processes. The experimentally obtained values show good consistency with the theoretical results calculated using WinXCom. Overall, the compositional tuning of structural and microstructural features governs the magnetic, electrical, and shielding performance, highlighting these perovskites as promising candidates for gamma-ray shielding and low-voltage varistor application
- 10 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCationic distribution, magnetic ordering, non-linear J-E characteristics, and sustainable gamma-ray shielding by Al3+ substituted CaCu3Ti4O12 quadruple perovskites
Herein, the influence of Al³⁺ substitution on the physical properties of quadruple perovskites, CaCu3-xAl2xTi4-xO12 (x = 0.0, 0.1, 0.3, 0.5), has been systematically investigated. Rietveld refinement of X-ray diffraction profiles confirms a strong preference of Al³⁺ ions for the octahedral (B-) site. Magnetic measurements M(T) (T = 5–300 K, H = 100 Oe) and M(H) (T = 5 K and 300 K, Hₘₐₓ = 70 kOe) reveal antiferromagnetic ordering at TN ≈ 25 K for the pristine sample. Upon Al³⁺ substitution, coexistence of antiferromagnetic, ferromagnetic, and paramagnetic phases is observed, with paramagnetism dominating at T ≫ TN. Soft ferromagnetic behaviour is evident at 300 K for x = 0.1–0.5 compositions. The nonlinear J–E characteristics at elevated temperatures (300–873 K) indicate switching behaviour, primarily attributed to Jahn–Teller distortion induced by Cu²⁺ ions. The maximum current density reaches 327 mA/cm² (x = 0.0) and increases to 429 mA/cm² for substituted samples (x = 0.1–0.5), representing exceptionally high reported values. Radiation shielding analysis shows enhanced linear and mass attenuation coefficients, along with higher fast neutron removal cross-sections, and reduced half-value and tenth-value layers compared to conventional gamma shielding materials in the 122–1330 keV range at 300 K. Radiation protection efficiency results indicate strong photon attenuation within ~122–511 keV. The variation of shielding parameters with incident photon energy is explained by three separate inelastic photon interaction processes. The experimentally obtained values show good consistency with the theoretical results calculated using WinXCom. Overall, the compositional tuning of structural and microstructural features governs the magnetic, electrical, and shielding performance, highlighting these perovskites as promising candidates for gamma-ray shielding and low-voltage varistor application
- 24 June 2024
- Published by Springer Nature in BioNanoScience
- Vol. 14 (3) , 2529-2540
Synthesis, Characterization, and Performance of Zirconia Nanoparticulates as an Antibacterial, Antifungal, and Anticancer Activity Agent
- 24 June 2024
- Published by Springer Nature in BioNanoScience
- Vol. 14 (3) , 2529-2540
Synthesis, Characterization, and Performance of Zirconia Nanoparticulates as an Antibacterial, Antifungal, and Anticancer Activity Agent
- 1 June 2024
- Published by Pleiades Publishing Ltd in Russian Journal of Nondestructive Testing
- Vol. 60 (6) , 614-635
Influence of Ca2+ Substitution on Elastic Properties of CaCu3Ti4O12 Quadruple Perovskites Determined by Ultrasonic Pulse Echo Selection Technique
The structural, microstructural, optical, and elastic properties of polycrystalline perovskite series, Ca1+xCu3–xTi4O12; x = 0–1.0, have been investigated employing X-ray powder diffractometry, scanning electron microscopy, UV–Vis spectroscopy, and ultrasonic pulse-echo selection technique at 300 K. The primary structural parameter and ultrasonic parameters; longitudinal wave velocity (V1), the amplitude of transmitted and reflected pulses ao/an were used to calculate porous values of various elastic parameters such as shear wave velocities Vs, mean sound velocity Vm, elastic moduli L, B, G, E, Debye temperature θ, Poisson’s ratio σ, acoustic impedance Z, internal friction Q–1, absorptivity A, adiabatic compressibility Ba, Lame’s constant λL, and Vickers micro-hardness Hv. The elastic constants were emended to a void-free state using eight distinct semi-empirical methods. These models are principally relying on the pore morphology in the material. Depending upon the correction model employed, Lo is found to decrease from ~21.5 to ~39.5%, Bo from ~17.4 to 45.6%, while Eo and Go are found to decrease from ~22 to 34% on Ca2+ substitution (x = 0–0.5) in the system. Besides, the observed increase in different elastic moduli for x = 1.0 composition is found to vary from 0.3 to 7%. The compositional dependency of elastic moduli has been explained in terms of the change in interatomic bonding strength produced by variations in interatomic distances, microstructure, and electronic configuration. The values of Pough’s ratio Bo/Go, Frantsevich’s ratio Go/Bo, and Poisson’s ratio σo suggest the brittle nature of prepared ceramics.
- 1 June 2024
- Published by Pleiades Publishing Ltd in Russian Journal of Nondestructive Testing
- Vol. 60 (6) , 614-635
Influence of Ca2+ Substitution on Elastic Properties of CaCu3Ti4O12 Quadruple Perovskites Determined by Ultrasonic Pulse Echo Selection Technique
The structural, microstructural, optical, and elastic properties of polycrystalline perovskite series, Ca1+xCu3–xTi4O12; x = 0–1.0, have been investigated employing X-ray powder diffractometry, scanning electron microscopy, UV–Vis spectroscopy, and ultrasonic pulse-echo selection technique at 300 K. The primary structural parameter and ultrasonic parameters; longitudinal wave velocity (V1), the amplitude of transmitted and reflected pulses ao/an were used to calculate porous values of various elastic parameters such as shear wave velocities Vs, mean sound velocity Vm, elastic moduli L, B, G, E, Debye temperature θ, Poisson’s ratio σ, acoustic impedance Z, internal friction Q–1, absorptivity A, adiabatic compressibility Ba, Lame’s constant λL, and Vickers micro-hardness Hv. The elastic constants were emended to a void-free state using eight distinct semi-empirical methods. These models are principally relying on the pore morphology in the material. Depending upon the correction model employed, Lo is found to decrease from ~21.5 to ~39.5%, Bo from ~17.4 to 45.6%, while Eo and Go are found to decrease from ~22 to 34% on Ca2+ substitution (x = 0–0.5) in the system. Besides, the observed increase in different elastic moduli for x = 1.0 composition is found to vary from 0.3 to 7%. The compositional dependency of elastic moduli has been explained in terms of the change in interatomic bonding strength produced by variations in interatomic distances, microstructure, and electronic configuration. The values of Pough’s ratio Bo/Go, Frantsevich’s ratio Go/Bo, and Poisson’s ratio σo suggest the brittle nature of prepared ceramics.
- 6 April 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (13) , 22989-23011
Co-existence of disordered fluorite and ordered pyrochlore phases in high energy mechanically milled Gd2Zr2O7 nanoparticulates
- 6 April 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (13) , 22989-23011
Co-existence of disordered fluorite and ordered pyrochlore phases in high energy mechanically milled Gd2Zr2O7 nanoparticulates
- 18 July 2022
- Published by Elsevier in Ceramics International
- Vol. 48 (21) , 31843-31849
Impact of Mn2+-Si4+ co-substitution on the electronic structure of Zn0.3Mn0.7Fe2O4 ferrites studied by X-ray photoelectron spectroscopy
- 18 July 2022
- Published by Elsevier in Ceramics International
- Vol. 48 (21) , 31843-31849
Impact of Mn2+-Si4+ co-substitution on the electronic structure of Zn0.3Mn0.7Fe2O4 ferrites studied by X-ray photoelectron spectroscopy
- 1 March 2022
- Published by IOP Publishing in Journal of Semiconductors
- Vol. 43 (3)
Fe3+-substitution effect on the thermal variation of J–E characteristics and DC resistivity of quadruple perovskite CaCu3Ti4O12
The electrical properties of cubic perovskite series, CaCu3–x Ti4–x Fe2x O12 with x = 0.0, 0.1, 0.3, 0.5, and 0.7, have been studied by employing current density as a function of electric field characteristics registered at different temperatures and thermal variations of direct current electrical resistivity measurements. All of the compositions exhibit strong non-ohmic behavior. The concentration dependence of breakdown field, the temperature at which switching action takes place, and maximum value of current density (J max) has been explained on account of structural, microstructural, and positron lifetime parameters. The highest ever reported value of J max = 327 mA/cm2 has been observed for pristine composition. The values of the nonlinear coefficient advise the suitability of ceramics for low-voltage varistor applications. The Arrhenius plots show typical semiconducting nature. The activation energy values indicate that electric conduction proceeds through electrons with deformation in the system.
- 1 March 2022
- Published by IOP Publishing in Journal of Semiconductors
- Vol. 43 (3)
Fe3+-substitution effect on the thermal variation of J–E characteristics and DC resistivity of quadruple perovskite CaCu3Ti4O12
The electrical properties of cubic perovskite series, CaCu3–x Ti4–x Fe2x O12 with x = 0.0, 0.1, 0.3, 0.5, and 0.7, have been studied by employing current density as a function of electric field characteristics registered at different temperatures and thermal variations of direct current electrical resistivity measurements. All of the compositions exhibit strong non-ohmic behavior. The concentration dependence of breakdown field, the temperature at which switching action takes place, and maximum value of current density (J max) has been explained on account of structural, microstructural, and positron lifetime parameters. The highest ever reported value of J max = 327 mA/cm2 has been observed for pristine composition. The values of the nonlinear coefficient advise the suitability of ceramics for low-voltage varistor applications. The Arrhenius plots show typical semiconducting nature. The activation energy values indicate that electric conduction proceeds through electrons with deformation in the system.
- 21 April 2021
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 32 (10) , 13630-13638
Probing reversal of orbital symmetry in CaCu3-xTi4-xFe2xO12 (x = 0.0–0.7) by X-ray absorption spectroscopy
- 21 April 2021
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 32 (10) , 13630-13638
Probing reversal of orbital symmetry in CaCu3-xTi4-xFe2xO12 (x = 0.0–0.7) by X-ray absorption spectroscopy
- 1 March 2021
- Published by International Association of Advanced Materials in Advanced Materials Letters
- Vol. 12 (3) , 1-6
Understanding of intriguing metal to semiconductor transition in Ni0.5Zn0.5Fe2O4 nanoparticulates
- 1 March 2021
- Published by International Association of Advanced Materials in Advanced Materials Letters
- Vol. 12 (3) , 1-6
Understanding of intriguing metal to semiconductor transition in Ni0.5Zn0.5Fe2O4 nanoparticulates
- 1 December 2020
- Published by International Association of Advanced Materials in Advanced Materials Letters
- Vol. 11 (12) , 1-8
Dielectric Relaxation and Suitability of Scaling parameters study on Mn0.7+xZn0.3SixFe2-2xO4 (x = 0.0 - 0.3) Ferrites
Dielectric Relaxation and Suitability of Scaling parameters study on Mn0.7+xZn0.3SixFe2-2xO4 (x = 0.0 - 0.3) Ferrites
- 1 December 2020
- Published by International Association of Advanced Materials in Advanced Materials Letters
- Vol. 11 (12) , 1-8
Dielectric Relaxation and Suitability of Scaling parameters study on Mn0.7+xZn0.3SixFe2-2xO4 (x = 0.0 - 0.3) Ferrites
Dielectric Relaxation and Suitability of Scaling parameters study on Mn0.7+xZn0.3SixFe2-2xO4 (x = 0.0 - 0.3) Ferrites