Ivy Ai Wei Tan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ivy Ai Wei Tan has a total of 82 co-authors. Here are the top co-authors by number of shared publications:
- Bassim Hamid Hameed
Department of Chemical Engineering, College of Engineering, Qatar University, Doha, Qatar
15 shared publications - Abdul Latif Ahmad
Universiti Sains Malaysia
11 shared publications - Mohammad Omar Abdullah
Universiti Malaysia Sarawak
8 shared publications Cirilo Nolasco-Hipolito
A Department of Chemical Engineering and Energy Sustainability, Faculty of Engineering , Universiti Malaysia Sarawak (UNIMAS) , Kota Samarahan , Malaysia
4 shared publicationsKopli Bujang
B Faculty of Resource Science & Technology , Universiti Malaysia Sarawak (UNIMAS) , Kota Samarahan , Malaysia
4 shared publications- Hafizah Abdul Halim Yun3 shared publications
Latest Publications
- 20 August 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 269
Waste-to-hydrogen pathways: A cross-sectoral review of feedstock potentials, process integration, and sustainability metrics
- 20 August 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 269
Waste-to-hydrogen pathways: A cross-sectoral review of feedstock potentials, process integration, and sustainability metrics
- Open Access
- 15 January 2026
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 237  (7) , 397
Corn Starch/Soybean Wax Double Coated Biochar-based Controlled-release Nitrogen Fertilizer: Water Retention, Release Kinetics and Okra Growth
- 15 January 2026
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 237  (7) , 397
Open AccessCorn Starch/Soybean Wax Double Coated Biochar-based Controlled-release Nitrogen Fertilizer: Water Retention, Release Kinetics and Okra Growth
- Open Access
- 6 August 2025
- Published by Springer Nature in Environmental Monitoring and Assessment
- Vol. 197  (9) , 1-22
Functionalized TiO2-waste-derived photocatalytic materials for emerging pollutant degradation: synthesis and optimization
Developing an effective, reusable photocatalyst that combines high photocatalytic efficiency with easy separation could significantly enhance the removal of organic pollutants. This study developed reusable photocatalysts by integrating TiOâ‚‚ with biomass-derived activated carbon (AC) and magnetite (Fe3O4) to enhance the removal of methylene blue (MB), acetaminophen (ACT), and their mixtures. Advanced microscopic and spectroscopic techniques, including FE-SEM, EDX, TEM, FTIR, XRD, and BET, were applied to identify the physicochemical properties of the composites. Both TiO2/AC-10% (436 m2/g) and TiO2/AC/Fe3O4 (494 m2/g) exhibited high surface areas, suggesting a significant abundance of active sites for pollutant degradation. Optimization of operational parameters, including pollutant concentration, irradiation time, and composite dosage, was conducted via response surface methodology (RSM) with a Box-Behnken design (BBD), using TiO2/AC-10%. Under optimized conditions, MB and ACT removal reached 98.37% and 87.28%, respectively within 120 min. The TiO2/AC/Fe3O4 composite maintained high efficiency over five reuse cycles. These waste-derived, magnetically separable photocatalysts offer a sustainable, efficient solution for organic pollutant removal in wastewater treatment. Graphical Abstract
- 6 August 2025
- Published by Springer Nature in Environmental Monitoring and Assessment
- Vol. 197  (9) , 1-22
Open AccessFunctionalized TiO2-waste-derived photocatalytic materials for emerging pollutant degradation: synthesis and optimization
Developing an effective, reusable photocatalyst that combines high photocatalytic efficiency with easy separation could significantly enhance the removal of organic pollutants. This study developed reusable photocatalysts by integrating TiOâ‚‚ with biomass-derived activated carbon (AC) and magnetite (Fe3O4) to enhance the removal of methylene blue (MB), acetaminophen (ACT), and their mixtures. Advanced microscopic and spectroscopic techniques, including FE-SEM, EDX, TEM, FTIR, XRD, and BET, were applied to identify the physicochemical properties of the composites. Both TiO2/AC-10% (436 m2/g) and TiO2/AC/Fe3O4 (494 m2/g) exhibited high surface areas, suggesting a significant abundance of active sites for pollutant degradation. Optimization of operational parameters, including pollutant concentration, irradiation time, and composite dosage, was conducted via response surface methodology (RSM) with a Box-Behnken design (BBD), using TiO2/AC-10%. Under optimized conditions, MB and ACT removal reached 98.37% and 87.28%, respectively within 120 min. The TiO2/AC/Fe3O4 composite maintained high efficiency over five reuse cycles. These waste-derived, magnetically separable photocatalysts offer a sustainable, efficient solution for organic pollutant removal in wastewater treatment. Graphical Abstract
- 30 October 2024
- Published by Elsevier in Journal of Crystal Growth
- Vol. 649
Simultaneous recovery of ammonium sulfate and ice from aqueous solution using eutectic freeze crystallization process
- 30 October 2024
- Published by Elsevier in Journal of Crystal Growth
- Vol. 649
Simultaneous recovery of ammonium sulfate and ice from aqueous solution using eutectic freeze crystallization process
- Open Access
- 28 June 2024
- Published by UNIMAS Publisher in Borneo Journal of Resource Science and Technology
- Vol. 14  (1) , 69-79
Simulation of Hybrid Microbial Fuel Cell-Adsorption System Performance: Effect of Anode Size on Bio-Energy Generation and COD Consumption Rate
Landfill leachate discharged into watercourse without proper treatment can pollute the water source due to its high chemical oxygen demand (COD). The high pollutant load in landfill leachate has become one of the potential substrates in bio-energy generation by using microbial fuel cell (MFC). MFC integrated with adsorption system has been introduced as an approach to overcome the limitation of stand-alone MFC, which is able to treat the landfill leachate more effectively while simultaneously generating bio-energy. Anode size has been reported to have a significant influence on the power generation of MFC via lab-scale experiments, however the simulation studies on MFC are still limited. This study aimed to develop a simulation model to predict the effect of graphite fiber brush anode size on the performance of a single chamber air-cathode hybrid MFC-Adsorption system, in terms of COD removal and bio-energy generation. The highest power density of 1.33 mW/m2 was achieved with 20% anode brush removed. The highest current generation of 2.37 mA and voltage of 7.11 mV was obtained with the largest anode surface area of 0.1288 m2 and resistance of 2.76 Ω. The highest COD consumption by electrogenic microorganisms was 4.96 x 10-9 Lmol/mg, and predicted to decrease with decreasing anode size. The efficiency of the simulation model could be further improved by incorporating parameters such as charge transfer kinetic at anode and cathode, adsorption effect by activated carbon as well as the substrate and microbial population behaviour. The simulation model developed was significant towards enhancing the bio-energy generation and reducing the cost of MFC for industrial application.
- 28 June 2024
- Published by UNIMAS Publisher in Borneo Journal of Resource Science and Technology
- Vol. 14  (1) , 69-79
Open AccessSimulation of Hybrid Microbial Fuel Cell-Adsorption System Performance: Effect of Anode Size on Bio-Energy Generation and COD Consumption Rate
Landfill leachate discharged into watercourse without proper treatment can pollute the water source due to its high chemical oxygen demand (COD). The high pollutant load in landfill leachate has become one of the potential substrates in bio-energy generation by using microbial fuel cell (MFC). MFC integrated with adsorption system has been introduced as an approach to overcome the limitation of stand-alone MFC, which is able to treat the landfill leachate more effectively while simultaneously generating bio-energy. Anode size has been reported to have a significant influence on the power generation of MFC via lab-scale experiments, however the simulation studies on MFC are still limited. This study aimed to develop a simulation model to predict the effect of graphite fiber brush anode size on the performance of a single chamber air-cathode hybrid MFC-Adsorption system, in terms of COD removal and bio-energy generation. The highest power density of 1.33 mW/m2 was achieved with 20% anode brush removed. The highest current generation of 2.37 mA and voltage of 7.11 mV was obtained with the largest anode surface area of 0.1288 m2 and resistance of 2.76 Ω. The highest COD consumption by electrogenic microorganisms was 4.96 x 10-9 Lmol/mg, and predicted to decrease with decreasing anode size. The efficiency of the simulation model could be further improved by incorporating parameters such as charge transfer kinetic at anode and cathode, adsorption effect by activated carbon as well as the substrate and microbial population behaviour. The simulation model developed was significant towards enhancing the bio-energy generation and reducing the cost of MFC for industrial application.
- 15 November 2023
- Published by Elsevier in Waste Management
- Vol. 173, 51-61
Synthesis of tapioca starch/palm oil encapsulated urea-impregnated biochar derived from peppercorn waste as a sustainable controlled-release fertilizer
- 15 November 2023
- Published by Elsevier in Waste Management
- Vol. 173, 51-61
Synthesis of tapioca starch/palm oil encapsulated urea-impregnated biochar derived from peppercorn waste as a sustainable controlled-release fertilizer
- 30 June 2022
- Published by Penerbit UMT, Universiti Malaysia Terengganu in Journal of Sustainability Science and Management
- Vol. 17  (6) , 66-78
DETERMINATION OF SUITABLE BIOCHAR PRECURSOR AS ALTERNATIVE FOR ENABLING ACCESS TO CLEAN WATER SUPPLY IN RURAL AREAS
This study aims to determine suitable biochar precursor for local production of biochar as an alternative low-cost solution to address the persistent water supply issue in rural areas in Sarawak. A series of physicochemical characterization and adsorption studies were conducted for biochar pyrolysed from bamboo, dried leaves, wood shavings, rice husk, tree branch and wood chip, in a stainless-steel canister (without oxygen) at 600oC for three hours using a muffle furnace. Bamboo was the only precursor which fulfilled the requirements for water treatment in rural areas, i.e., biochar yield, structural integrity in water and adsorption characteristics. The pyrolysis of bamboo achieved a biochar yield of 32.8%, which attributed to the high fixed carbon content of 70.9% required for adsorption. The biochar consisted of homogeneous carbon structures with BET surface area of 317 m2/g, total pore volume of 0.189 cm3/g and micropores averaging 1.218 nm, which demonstrated favourable adsorption characteristics. The selection of bamboo as precursor is practical in rural areas as it is easily obtained and safe to be pyrolyzed into biochar. The application of biochar for water treatment helps to overcome the water supply issues and promote sustainable biomass waste management in rural areas.
- 30 June 2022
- Published by Penerbit UMT, Universiti Malaysia Terengganu in Journal of Sustainability Science and Management
- Vol. 17  (6) , 66-78
DETERMINATION OF SUITABLE BIOCHAR PRECURSOR AS ALTERNATIVE FOR ENABLING ACCESS TO CLEAN WATER SUPPLY IN RURAL AREAS
This study aims to determine suitable biochar precursor for local production of biochar as an alternative low-cost solution to address the persistent water supply issue in rural areas in Sarawak. A series of physicochemical characterization and adsorption studies were conducted for biochar pyrolysed from bamboo, dried leaves, wood shavings, rice husk, tree branch and wood chip, in a stainless-steel canister (without oxygen) at 600oC for three hours using a muffle furnace. Bamboo was the only precursor which fulfilled the requirements for water treatment in rural areas, i.e., biochar yield, structural integrity in water and adsorption characteristics. The pyrolysis of bamboo achieved a biochar yield of 32.8%, which attributed to the high fixed carbon content of 70.9% required for adsorption. The biochar consisted of homogeneous carbon structures with BET surface area of 317 m2/g, total pore volume of 0.189 cm3/g and micropores averaging 1.218 nm, which demonstrated favourable adsorption characteristics. The selection of bamboo as precursor is practical in rural areas as it is easily obtained and safe to be pyrolyzed into biochar. The application of biochar for water treatment helps to overcome the water supply issues and promote sustainable biomass waste management in rural areas.
- 30 June 2022
- Published by Penerbit UMT, Universiti Malaysia Terengganu in Journal of Sustainability Science and Management
- Vol. 17  (6) , 3-23
MODELLING THE EFFECT OF WOOD AND MAIZE COB-DERIVED BIOCHAR APPLICATION ON SOIL DYNAMICS AND MAIZE GROWTH FOR SUSTAINABLE AGRICULTURE
Intensive agriculture has degraded global agricultural land and resulted in a food crisis. The application of biochar in agricultural soil has been proven effective at improving soil quality and increasing crop yield. This study aims to develop a simulation and investigate the effect of wood-derived biochar (WBC) and maize cob-derived biochar (MBC) at different application rates on soil pH, soil cation exchange capacity (CEC), soil organic carbon (SOC) and the productivity of the maize cropping system. The prediction regarding the effect of biochar on soil pH was the most accurate of all the parameters studied. The simulation was good at predicting the change of properties in calcareous clay soil for both WBC and MBC, as well as WBC in acidic, sandy soil. The results demonstrated that amendments to both WBC and MBC successfully improved the soil pH, SOC and CEC. The effect was more significant when higher biochar application rates were applied. The biochar amendment enhanced the properties of acidic sandy soil more significantly as compared to calcareous clay soil. Overall, WBC and MBC are potential green fertilisers capable of enhancing soil quality for the sustainable development in agriculture.
- 30 June 2022
- Published by Penerbit UMT, Universiti Malaysia Terengganu in Journal of Sustainability Science and Management
- Vol. 17  (6) , 3-23
MODELLING THE EFFECT OF WOOD AND MAIZE COB-DERIVED BIOCHAR APPLICATION ON SOIL DYNAMICS AND MAIZE GROWTH FOR SUSTAINABLE AGRICULTURE
Intensive agriculture has degraded global agricultural land and resulted in a food crisis. The application of biochar in agricultural soil has been proven effective at improving soil quality and increasing crop yield. This study aims to develop a simulation and investigate the effect of wood-derived biochar (WBC) and maize cob-derived biochar (MBC) at different application rates on soil pH, soil cation exchange capacity (CEC), soil organic carbon (SOC) and the productivity of the maize cropping system. The prediction regarding the effect of biochar on soil pH was the most accurate of all the parameters studied. The simulation was good at predicting the change of properties in calcareous clay soil for both WBC and MBC, as well as WBC in acidic, sandy soil. The results demonstrated that amendments to both WBC and MBC successfully improved the soil pH, SOC and CEC. The effect was more significant when higher biochar application rates were applied. The biochar amendment enhanced the properties of acidic sandy soil more significantly as compared to calcareous clay soil. Overall, WBC and MBC are potential green fertilisers capable of enhancing soil quality for the sustainable development in agriculture.