Ruggero Loi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ruggero Loi has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Brian Corbett
Tyndall National Institute, Lee Maltings, Cork, Ireland
4 shared publications - Agnieszka Gocalinska
Tyndall National Institute, Dyke Parade, T12 R5CP Cork, Ireland
3 shared publications Antonio Jose Trindade
X-Celeprint Ltd., Cork, Ireland
3 shared publications- Emanuele Pelucchi
Tyndall National Institute, Lee Maltings, Cork, Ireland
3 shared publications - Jing Zhang
Ghent University - IMEC
3 shared publications - Biwei Pan
Ghent University - IMEC
2 shared publications
Latest Publications
- 29 May 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (11) , 20833-20842
56-Gb/s 3D-integrated silicon optical transmitter based on micro-transfer printing
We present an optical transmitter consisting of a SiGe BiCMOS driver amplifier heterogeneously integrated through micro-transfer printing onto a silicon photonic chip that contains a Mach-Zehnder modulator (MZM) and optical couplers. The driver has a footprint of only 200 µm × 300 µm, and features small bond pads of 20 µm × 20 µm. It was fabricated using a modified SiGe BiCMOS on SOI process to enable the release process prior to micro-transfer printing. The post-print metallization process to contact the EIC with the PIC consists of spin coating a layer of divinylsiloxane-bis-benzocyclobutene (DVS-BCB) to create a ramp to overcome the 20 µm step height, after which a gold metal layer is deposited to connect the driver to the MZM. To verify the operation of the optical transmitter, a high-speed measurement setup is used to capture eye diagrams. The 3D-integrated transmitter achieves 56 Gb∕s non-return to zero (NRZ) with a 5-tap feed-forward equalizer (FFE) and 28 GBd 4-level pulse amplitude modulation (PAM-4) with a 5-tap FFE and nonlinearity pre-compensation, both at a total transmitter power efficiency of 9.1 pJ∕bit. Integration through micro-transfer printing offers the possibility of greatly increasing scalability and fabrication throughput of short-reach optical transceivers for data centers.
- 29 May 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (11) , 20833-20842
56-Gb/s 3D-integrated silicon optical transmitter based on micro-transfer printing
We present an optical transmitter consisting of a SiGe BiCMOS driver amplifier heterogeneously integrated through micro-transfer printing onto a silicon photonic chip that contains a Mach-Zehnder modulator (MZM) and optical couplers. The driver has a footprint of only 200 µm × 300 µm, and features small bond pads of 20 µm × 20 µm. It was fabricated using a modified SiGe BiCMOS on SOI process to enable the release process prior to micro-transfer printing. The post-print metallization process to contact the EIC with the PIC consists of spin coating a layer of divinylsiloxane-bis-benzocyclobutene (DVS-BCB) to create a ramp to overcome the 20 µm step height, after which a gold metal layer is deposited to connect the driver to the MZM. To verify the operation of the optical transmitter, a high-speed measurement setup is used to capture eye diagrams. The 3D-integrated transmitter achieves 56 Gb∕s non-return to zero (NRZ) with a 5-tap feed-forward equalizer (FFE) and 28 GBd 4-level pulse amplitude modulation (PAM-4) with a 5-tap FFE and nonlinearity pre-compensation, both at a total transmitter power efficiency of 9.1 pJ∕bit. Integration through micro-transfer printing offers the possibility of greatly increasing scalability and fabrication throughput of short-reach optical transceivers for data centers.
- 13 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 32 (2: 3-D Hor) , 1-8
Micro-Transfer Printing of SiGe BiCMOS Electronic Chiplets on Silicon
We demonstrate micro-transfer printing ($\mu$TP) and post-printing metallization of thin electronic chiplets on silicon, with a view to heterogeneously integrate electronic integrated circuits (EICs) with photonic integrated circuits (PICs). $\mu$TP decouples the fabrication of EICs and PICs, and simultaneously enables their tight integration with high-throughput, small form-factor and on wafer-scale. In this study, we successfully established the process flow for releasing and printing 300 $\mu$m × 200 $\mu$m SiGe BiCMOS electronic driver chiplets and electrically connecting these chiplets using a polymer ramp to overcome the 20-$\mu$m chiplet thickness, providing a gain of 14 dB and bandwidth of over 35 GHz with low-parasitic interconnections. The proposed methodology provides a practical and mass-producible solution to realize the stacking of EICs on silicon photonic wafers for emerging applications such as co-packaged optics (CPO).
- 13 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 32 (2: 3-D Hor) , 1-8
Micro-Transfer Printing of SiGe BiCMOS Electronic Chiplets on Silicon
We demonstrate micro-transfer printing ($\mu$TP) and post-printing metallization of thin electronic chiplets on silicon, with a view to heterogeneously integrate electronic integrated circuits (EICs) with photonic integrated circuits (PICs). $\mu$TP decouples the fabrication of EICs and PICs, and simultaneously enables their tight integration with high-throughput, small form-factor and on wafer-scale. In this study, we successfully established the process flow for releasing and printing 300 $\mu$m × 200 $\mu$m SiGe BiCMOS electronic driver chiplets and electrically connecting these chiplets using a polymer ramp to overcome the 20-$\mu$m chiplet thickness, providing a gain of 14 dB and bandwidth of over 35 GHz with low-parasitic interconnections. The proposed methodology provides a practical and mass-producible solution to realize the stacking of EICs on silicon photonic wafers for emerging applications such as co-packaged optics (CPO).
- Open Access
- 8 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 56 (1) , 1-8
Edge-Coupling of O-Band InP Etched-Facet Lasers to Polymer Waveguides on SOI by Micro-Transfer-Printing
O-band InP etched facets lasers were heterogeneously integrated by micro-transfer-printing into a 1.54 μm deep recess created in the 3 μm thick oxide layer of a 220 nm SOI wafer. A 7 × 1.5 μm 2 cross-section, 2 mm long multimode polymer waveguide was aligned to the ridge post-integration by e-beam lithography with <; 0.7 μm lateral misalignment and incorporated a tapered silicon waveguide. A 170 nm thick metal layer positioned at the bottom of the recess adjusts the vertical alignment of the laser and serves as a thermal via to sink the heat to the Si substrate. This strategy shows a roadmap for active polymer waveguide-based photonic integrated circuits.
- 8 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 56 (1) , 1-8
Open AccessEdge-Coupling of O-Band InP Etched-Facet Lasers to Polymer Waveguides on SOI by Micro-Transfer-Printing
O-band InP etched facets lasers were heterogeneously integrated by micro-transfer-printing into a 1.54 μm deep recess created in the 3 μm thick oxide layer of a 220 nm SOI wafer. A 7 × 1.5 μm 2 cross-section, 2 mm long multimode polymer waveguide was aligned to the ridge post-integration by e-beam lithography with <; 0.7 μm lateral misalignment and incorporated a tapered silicon waveguide. A 170 nm thick metal layer positioned at the bottom of the recess adjusts the vertical alignment of the laser and serves as a thermal via to sink the heat to the Si substrate. This strategy shows a roadmap for active polymer waveguide-based photonic integrated circuits.
- Open Access
- 13 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (24) , 5935-5941
Thermal Analysis of InP Lasers Transfer Printed to Silicon Photonics Substrates
The thermal performance of Fabry-Perot InP lasers integrated onto different silicon photonics substrates by microtransfer printing is assessed. 500-μm-long ridge waveguide lasers on the original 350-μm-thick InP have an experimental thermal impedance, ZEXP, of 57 K/W that is reduced to 38 K/W after printing to a 500-μm-thick Si substrate. ZEXP for lasers printed on silicon-on-insulator wafers is ~94 K/W, which is more than two times higher than that of the laser printed on the Si substrate. ZEXP of lasers printed on thermally insulating layers like benzocyclobutene (BCB) or SiO 2 increases with the thickness of the layer. BCB adhesive layers as thin as 50 nm limit ZEXP to be greater than 55 K/W. The thermal properties for the different situations were modeled using finite-element simulations which confirmed the experimental results within 10% accuracy. The simulations show how changes in the geometry and the materials of the integration platform can influence the resulting thermal impedance.
- 13 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (24) , 5935-5941
Open AccessThermal Analysis of InP Lasers Transfer Printed to Silicon Photonics Substrates
The thermal performance of Fabry-Perot InP lasers integrated onto different silicon photonics substrates by microtransfer printing is assessed. 500-μm-long ridge waveguide lasers on the original 350-μm-thick InP have an experimental thermal impedance, ZEXP, of 57 K/W that is reduced to 38 K/W after printing to a 500-μm-thick Si substrate. ZEXP for lasers printed on silicon-on-insulator wafers is ~94 K/W, which is more than two times higher than that of the laser printed on the Si substrate. ZEXP of lasers printed on thermally insulating layers like benzocyclobutene (BCB) or SiO 2 increases with the thickness of the layer. BCB adhesive layers as thin as 50 nm limit ZEXP to be greater than 55 K/W. The thermal properties for the different situations were modeled using finite-element simulations which confirmed the experimental results within 10% accuracy. The simulations show how changes in the geometry and the materials of the integration platform can influence the resulting thermal impedance.
- 21 November 2017
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 7 (12) , 4408-4414
Comparison of InGaAs and InAlAs sacrificial layers for release of InP-based devices
Heterogeneous integration of InP devices to Si substrates by adhesive-less micro transfer printing requires flat surfaces for optimum attachment and thermal sinking. InGaAs and InAlAs sacrificial layers are compared for the selective undercut of InP coupons by FeCl3:H2O (1:2). InAlAs offers isotropic etches and superior selectivity (> 4,000) to InP when compared with InGaAs. A 500 nm thick InAlAs sacrificial layer allows the release of wide coupons with a surface roughness < 2 nm and a flatness < 20 nm. The InAlAs release technology is applied to the transfer printing of a pre-fabricated InP laser to a Si substrate.
- 21 November 2017
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 7 (12) , 4408-4414
Comparison of InGaAs and InAlAs sacrificial layers for release of InP-based devices
Heterogeneous integration of InP devices to Si substrates by adhesive-less micro transfer printing requires flat surfaces for optimum attachment and thermal sinking. InGaAs and InAlAs sacrificial layers are compared for the selective undercut of InP coupons by FeCl3:H2O (1:2). InAlAs offers isotropic etches and superior selectivity (> 4,000) to InP when compared with InGaAs. A 500 nm thick InAlAs sacrificial layer allows the release of wide coupons with a surface roughness < 2 nm and a flatness < 20 nm. The InAlAs release technology is applied to the transfer printing of a pre-fabricated InP laser to a Si substrate.
- 13 June 2017
- Published by Optica Publishing Group in Optics Express
- Vol. 25 (13) , 14290-14299
Silicon photonics fiber-to-the-home transceiver array based on transfer-printing-based integration of III-V photodetectors
A 4-channel silicon photonics transceiver array for Point-to-Point (P2P) fiber-to-the-home (FTTH) optical networks at the central office (CO) side is demonstrated. A III-V O-band photodetector array was integrated onto the silicon photonic transmitter through transfer printing technology, showing a polarization-independent responsivity of 0.39 - 0.49 A/W in the O-band. The integrated PDs (30 × 40 μm2 mesa) have a 3 dB bandwidth of 11.5 GHz at −3 V bias. Together with high-speed C-band silicon ring modulators whose bandwidth is up to 15 GHz, operation of the transceiver array at 10 Gbit/s is demonstrated. The use of transfer printing for the integration of the III-V photodetectors allows for an efficient use of III-V material and enables the scalable integration of III-V devices on silicon photonics wafers, thereby reducing their cost.
- 13 June 2017
- Published by Optica Publishing Group in Optics Express
- Vol. 25 (13) , 14290-14299
Silicon photonics fiber-to-the-home transceiver array based on transfer-printing-based integration of III-V photodetectors
A 4-channel silicon photonics transceiver array for Point-to-Point (P2P) fiber-to-the-home (FTTH) optical networks at the central office (CO) side is demonstrated. A III-V O-band photodetector array was integrated onto the silicon photonic transmitter through transfer printing technology, showing a polarization-independent responsivity of 0.39 - 0.49 A/W in the O-band. The integrated PDs (30 × 40 μm2 mesa) have a 3 dB bandwidth of 11.5 GHz at −3 V bias. Together with high-speed C-band silicon ring modulators whose bandwidth is up to 15 GHz, operation of the transceiver array at 10 Gbit/s is demonstrated. The use of transfer printing for the integration of the III-V photodetectors allows for an efficient use of III-V material and enables the scalable integration of III-V devices on silicon photonics wafers, thereby reducing their cost.