Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Kashif Mushtaq has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Nano-Enhanced Binary Eutectic PCM with SiC for Solar HDH Desalination Systems

    by Rahul Agrawal, Kashif Mushtaq, Daniel López Pedrajas, Iqra Irfan, Breogán Pato-Doldán

    Freshwater scarcity is increasing day by day and has already reached a threatening level, especially in remotely populated areas. One of the technological solutions to this rising concern could be the use of the solar-based humidification–dehumidification (SHDH) method for water desalination. This technology is a promising solution but has challenges such as solar intermittency. This challenge can be solved by integrating SHDH with the phase change material as a solar energy storage medium. Therefore, a novel nano-enhanced binary eutectic phase change material (NEPCM) was developed in this project. PCM consisting of 70 wt.% stearic acid (ST) and 30 wt.% suberic acid (SBU) with a varying concentration of silicon carbide (SiC) nanoparticles (NPs) (0.1 to 3 wt.%) was synthesized specifically considering the need of SHDH application. The systematic thermophysical characterization was conducted to investigate their energy storage capacity, thermal durability, and performance consistency over repeated cycles. DSC analysis revealed that the addition of SiC NPs preserved the thermal stability of the NEPCM, while the phase transition temperature remained nearly unchanged with a variation of less than 0.74%. The value of latent heat is inversely related to the nanoparticle concentration, i.e., from 142.75 kJ/kg for the base PCM to 131.24 kJ/kg at 3 wt.% loading. This corresponds to reductions in latent heat ranging between 0.98% and 8.06%. The FTIR measurement confirms that no chemical reactions or no new functional groups were formed. All original functional groups of ST and SBU remained intact, showing that incorporating the SiC NP to the PCM lead to physical interactions (e.g., hydrogen bonding or surface adsorption). The TGA analysis showed that the SiC NPs in the NEPCM act as supporting material, and its nano-doping enhanced the final degradation temperature and thermal stability. There was negligible change in thermal conductivity for nanoparticle loadings of 0.1% and 0.4%; however, it increased progressively by 5.2%, 10.8%, 23.12%, and 25.8% at nanoparticle loadings of 0.7%, 1%, 2%, and 3%, respectively, at 25 °C. Thermal reliability was analyzed through a DSC thermal cycling test which confirmed the suitability of the material for the desired applications.


  • Self-discharge mitigation in a liquid metal displacement battery

    by Kashif Mushtaq, Ji Zhao, Norbert Weber, Adelio Mendes, Donald R. Sadoway


  • Novel Aluminum-Ion Based Non-Aqueous Redox Flow Battery

    by Kashif Mushtaq, Sofia Delgado, Adelio Mendes

  • Step Toward Eco-Friendly Green Source of Non-Aqueous Electrolytes for Redox Flow Battery

    by Kashif Mushtaq, Adelio Mendes

    The efficient utilization of energy from non-exhaustive resources without adverse effects on the environment is a way forward for the sustainable development of society. The intermittent nature of renewable energy from non-exhaustive resources such as solar, wind, etc., requires a large-scale and advanced energy storage system to eliminate the impact of intermittency on the power grid. Redox flow battery (RFB) technology is one of the promising candidates for large-scale grid systems. Present commercial RFB technology is based on the redox reactions of electroactive metals, which are constrained by material abundance, cost, and environmental issues. These issues are prompting scientists to look into organic-based technologies as potential metal-free battery alternatives. Organic-based materials offer structural diversity of organic molecules to adjust the electrolyte materials' thermodynamics and redox characteristics, in addition to low cost and scalability. This opens the door to the development of green and sustainable energy storage devices. Despite development over the last decade, organic compound exploitation for RFB remains limited. Organics with limited ionic conductivity and poorly defined conducting channels have poor voltage efficiency and cyclability. In aqueous flow batteries, the cell potential is also limited by the electrolysis of water. The scientific community, on the other hand, is addressing this issue by introducing the non-aqueous RFB (NAqRFB). Quinones are the most redox-active moieties found in natural organic materials, and they play a critical role in biological electron transport. They are a class of molecules that are formed from aromatic compounds like benzene or naphthalene and have a fully conjugated cyclic diketone structure with a redox reaction based on the rearrangement of the conjugated double bond. 1,4-naphthoquinone (NQ) is investigated as a possible negolyte candidate. NQ as metal-free organic negolyte was coupled with metal acetylacetonate-based posolytes, M(acac), where M = Cr, V, Mn. Both types of redox species (metal & metal-free) have good solubility in the solvent - Dimethylacetamide (DMA) - and ionic conductivity was enhanced using the supporting electrolyte of TEABF4. Cyclic voltammetry (CV) analysis using glassy carbon working electrode (GCE) highlighted that NQ offers reversibility; the high value of negative redox potential -1.75 V vs. Ag/Ag+ enables higher cell potential and posses no irreversible side reactions. The electrochemical stability of the negolyte was further tested using the symmetrical cell having an electrolyte of 0.06 M concentration of NQ as redox species. The electrolyte flow from the reservoir, cathode, and anode in a series arrangement. The redox species are reduced at the cathode and then oxidized at the anode, which helps maintain the state-of-charge (SOC) at 50 %. The cell was operated for 50 cycles at the C-rate = 1C, i.e., 2.75 mA⋅cm-2 at the cutoff potentials of ±0.3 V. The energy efficiency of that symmetric cell was 99.7 %, and discharge capacity retention was 99.967%. These results are validated from the reported study by Yu Ding, 2016. This strengthen the motivation of using the NQ as metal-free organic negolyte for single NAqRFB-cell. The insertion of the mentioned metals (Cr, V, Mn) at the posolyte while keeping NQ ion at the negolyte ensured the generation of novel chemistries for NAqRFBs, in detail NQ||Cr, NQ||V, and NQ||Mn, with cell potential differences of 3.25 V, 2.2 V, and 2.45 V, respectively. Detailed characterization was performed using polarization, EIS, and charge-discharge cycling (CDC) – Table 1. Post-mortem CVs of the electrolyte using GCE highlight the stability of the electrolyte after intensive CDC. The RFB assembled with NQ||Cr offered the highest capacity and energy density. However, it was faced with lower energy efficiency. The post-mortem analyses on the posolyte signify that there was crossover through the membrane, which ended up with a contaminated electrolyte (mixture with negolyte chemistry) that affected the extended capacity of the cell. The RFB composed of NQ||V offers the 2nd highest capacity and energy density than others and is two times more than reported V||V NAqRFB. Reinforced membranes permit to decrease the permeability of the membrane toward smaller ions of NQ as compared to V2+ redox ions. Furthermore, the NQ||Mn battery demonstrated a stable performance up to 25 cycles having higher efficiencies and with a decent energy density of ca. 60 mWh.g-1 . NQ has high solubility of 1.5 M in DMA and future work at higher capacities is in progress for in-depth study covering other aspects. The study may ascertain the feasibility of NQ-based RFB to be the eco-friendly green alternate battery chemistry. Figure 1

  • Nanoparticles Coated Electrodes for Vanadium-Based Non-Aqueous Redox Flow Battery

    by Kashif Mushtaq, Sofia Delgado, Adelio Mendes

    Redox flow batteries (RFBs) are a promising technology for large-scale energy storage. However, their main limitation concerns their inherent lower energy density compared to other batteries such as Li-ion, Ni-metal hydride, Ni-Cd, etc. The research community is addressing this challenge with the introduction of the non-aqueous RFB (NAqRFB). The electrodes composing the NAqRFB play a vital role in the redox reaction mechanism as their microstructure is ultimately responsible for the ohmic polarisation of the cell and mainly for the activation polarisation. Pristine carbon-felts are typically used in Vanadium based redox flow batteries. These show good electrical conductivity and excellent mechanical stability. Still, they fail both to assure fast kinetics and exemplary reactants diffusion due to poor electrochemical surface area and low permeability of fibers to the electrolyte, which is reflected through high charge transfer resistances. Hence, it is crucial to develop high-performance, robust and tailored-made electrodes that improve the electrochemical activity of redox species in non-aqueous electrolytes while ensuring a blockage-free path for the electrolyte to reach these active electrochemical sites. Several thermal and/or chemical treatments (e.g., nitrogen doping, sulfuric acid leaching) or even surface decoration with particles (SnO2/TiO2, Pt, graphite) had been applied to carbon felts to ensure higher wettability and to tune their surface chemistry to reach more excellent reversibility of vanadium redox reactions at the electrodes. These attempts had been explained for aqueous systems. However, there is a gap in the literature to have a systematic study on the modified/coated electrodes with several carbon nanoparticles of different shapes and sizes, surface areas, conductivity, and their effect on the overall performance and stability of a non-aqueous Vanadium RFB. Moreover, tuning the electrode with an ionomer to the carbon particles should also be assessed as it may contribute to generating a longer ionic conductive path onto the 3D microstructure of carbon felts. The present work acknowledges the impact of adding nanoparticles such as reduced graphene oxide (rGO), graphene (G), multi-walled carbon nanotubes (CNT), carbon black as Vulcan XC72 (V), and carbon black as Ketjen (K) to carbon felts. The electrodes were prepared by a facile and fast drop-casting coating technique. Nafion ionomer was used as a binder, and its concentration was optimized to increase the number of triple-phase boundaries (TPBs). More TPBs consider a simultaneous boosted interaction between the ion conduction phase (electrolyte/ionomer), electron conduction phase (carbon felt fibers), and the 3D porous network for better electrolyte transport, which results in higher energy efficiencies. After extensive cyclic voltammetry, SEM and EDS analysis, it was observed that the addition of CNT or Graphene coatings at both the cathode and anode pose a better bargain between increased electroactivity and enhanced stability towards both redox couple reactions. The adhesion of the nanoparticles using the drop-casting method was highly influential, mainly for rGO and CNT coated electrodes, as they demonstrate widespread dispersion of nanoparticles on their fibers. The enhancement of surface defects suggests an increment in the number of active sites for the redox reactions is a possibility, confirmed by the higher electrochemical surface areas attained. Addition of the ionomer in a ratio of I/C = 15 wt. % is effective and offers good binding of the carbon nanoparticles. Charge Discharge Cycling (CDC) was used to assess the performance of the redox flow cell. The cell was assembled using each prepared sample of coated carbon felts and operated for 25 cycles at a C-rate = C/2, i.e., equivalent to the current density of 4.2 mA⋅cm-2. Post-mortem analyses reveal that the nanoparticles generally remain attached to the fibers after intense CDC. The carbon felt containing CNT nanoparticles depicts the most similar structure compared to its beginning of life. Nonetheless, an optimized suggested configuration for operating a single NAqRFB-cell may include using graphene-coated carbon felts at the negative side and CNT-coated carbon felts at the positive side of the NAqRFB. Advancements in this domain are attractive since it paves the way for designing stacks of reduced size and lowers the overall capital expenditure of installing the NAqRFB after encouraging the pilot level commercialization and screening. The results are summarized in Table 1, and this work is still in progress for an in-depth study covering other aspects. Figure 1

  • Bioelectrochemical energy storage in a Microbial Redox Flow Cell

    by Márcia S.S. Santos, Luciana Peixoto, Kashif Mushtaq, Celia Dias-Ferreira, Adélio Mendes, M. Madalena Alves