Maria Cristina Gagliano
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Maria Cristina Gagliano has a total of 79 co-authors. Here are the top co-authors by number of shared publications:
- Dainis Sudmalis
Department of Environmental Technology, Wageningen University and Research, Bornse Weilanden 9, 6708 WG Wageningen, The Netherlands
8 shared publications Hardy Temmink
Wetsus – European Centre of Excellence for Sustainable Water Technology, Leeuwarden, the Netherlands
6 shared publications- Andrea Gianico
Water Research Institute, National Research Council (CNR-IRSA) , Strada Provinciale 35d, 9
5 shared publications - Camilla Maria Braguglia
Water Research Institute (IRSA), National Research Council (CNR), Strada Provinciale 35d, km 0.7, 00010, Montelibretti, Rome, Italy
5 shared publications - Simona Rossetti
Water Research Institute, CNR-IRSA, National Research Council, Strada Provinciale 35d, km 0,700, Montelibretti, 00010 Rome, Italy
5 shared publications H. Temmink
Department of Environmental Technology, Wageningen University and Research, Bornse Weilanden 9, 6708, WG, Wageningen, the Netherlands
4 shared publications
Latest Publications
- Open Access
- 11 October 2026
- Published by Elsevier in Water Research
- Vol. 309
Integrating hydrogen delivery and in situ water removal for biomethanation in a hollow fiber membrane biofilm reactor (HF-MBfR)
- 11 October 2026
- Published by Elsevier in Water Research
- Vol. 309
Open AccessIntegrating hydrogen delivery and in situ water removal for biomethanation in a hollow fiber membrane biofilm reactor (HF-MBfR)
- Open Access
- 30 April 2026
- Published by Elsevier in Bioresource Technology
- Vol. 455, 134744
Mixed microbial culture-derived flocculant overproduction from fermented waste streams in membrane and chemostat bioreactors as novel pathway for organics valorization
- 30 April 2026
- Published by Elsevier in Bioresource Technology
- Vol. 455, 134744
Open AccessMixed microbial culture-derived flocculant overproduction from fermented waste streams in membrane and chemostat bioreactors as novel pathway for organics valorization
- Open Access
- 16 February 2026
- Published by Elsevier in SSRN Electronic Journal
EPS Overproduction from VFA-Rich Wastewater by Mixed Microbial Cultures under Nitrogen Limitation and Short SRT: A New Route for VFA Valorization
Volatile fatty acids (VFAs) from fermented wastewater are valuable biopolymer precursors. While microbial conversion of VFAs into polyhydroxyalkanoates (PHAs) is widely studied, their conversion into extracellular polymeric substances (EPS)-based flocculants remains largely unexplored. This study investigates EPS production from VFA-rich synthetic wastewater using mixed microbial cultures (MMC) under EPS-overproducing conditions (solid retention time (SRT) of 3 days and nitrogen limitation: COD:N 100). A continuous stirred-tank reactor (CSTR) and a membrane bioreactor (MBR) were compared under these conditions to assess the influence of process configuration on EPS yields, composition, and flocculation performance. VFA conversion was relatively high (~80%) in the CSTR, but lower in the MBR ( 2) in the soluble fraction and protein-rich (PS:PN < 0.5) in the bound fraction. All EPS were anionic (0.5–2.6 meq g⁻¹) with high molecular weight (0.17–3.7 MDa). VFA-derived EPS demonstrated high flocculation efficiency (>90%) with Ca²⁺, comparable to commercial polyacrylamide (PAM, 92%), regardless of EPS type. These findings show EPS-flocculant production by MMC from VFA-rich wastewater, offering a sustainable route to convert waste carbon into functional biopolymers and support resource recovery and green flocculants development.
- 16 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEPS Overproduction from VFA-Rich Wastewater by Mixed Microbial Cultures under Nitrogen Limitation and Short SRT: A New Route for VFA Valorization
Volatile fatty acids (VFAs) from fermented wastewater are valuable biopolymer precursors. While microbial conversion of VFAs into polyhydroxyalkanoates (PHAs) is widely studied, their conversion into extracellular polymeric substances (EPS)-based flocculants remains largely unexplored. This study investigates EPS production from VFA-rich synthetic wastewater using mixed microbial cultures (MMC) under EPS-overproducing conditions (solid retention time (SRT) of 3 days and nitrogen limitation: COD:N 100). A continuous stirred-tank reactor (CSTR) and a membrane bioreactor (MBR) were compared under these conditions to assess the influence of process configuration on EPS yields, composition, and flocculation performance. VFA conversion was relatively high (~80%) in the CSTR, but lower in the MBR ( 2) in the soluble fraction and protein-rich (PS:PN < 0.5) in the bound fraction. All EPS were anionic (0.5–2.6 meq g⁻¹) with high molecular weight (0.17–3.7 MDa). VFA-derived EPS demonstrated high flocculation efficiency (>90%) with Ca²⁺, comparable to commercial polyacrylamide (PAM, 92%), regardless of EPS type. These findings show EPS-flocculant production by MMC from VFA-rich wastewater, offering a sustainable route to convert waste carbon into functional biopolymers and support resource recovery and green flocculants development.
- Open Access
- 5 February 2026
- Published by Elsevier in Water Research X
- Vol. 30
Membrane biofilm reactor (MBfR) enabling optimal H2 delivery and supporting minimal nutrient supplementation to hydrogenotrophic biofilms
- 5 February 2026
- Published by Elsevier in Water Research X
- Vol. 30
Open AccessMembrane biofilm reactor (MBfR) enabling optimal H2 delivery and supporting minimal nutrient supplementation to hydrogenotrophic biofilms
- 5 February 2026
- Published by American Chemical Society (ACS) in ACS Applied Engineering Materials
- Vol. 4 (2) , 650-660
Poly( N -isopropylmethacrylamide) Nanohydrogel Coatings to Limit the Adhesion of Microorganisms in Drinking Water Distribution Systems: Stability and Optimization
Biofilm formation in drinking water distribution systems (DWDSs) presents a significant challenge, compromising both water quality and infrastructure lifetime. Recently, a nanohydrogel coating was demonstrated to have excellent antiadhesive properties toward drinking water microorganisms, making it a promising approach to alleviate biofilm formation in DWDS systems. However, the used coating procedure was not suitable for large surface areas and the stability of the coating under various physicochemical conditions was not assessed. This study proposes an optimized coating procedure for poly-(vinyl chloride) (PVC)-based drinking water piping and evaluates the stability of this poly-(N-isopropylmethacrylamide) (PNIPAM) based nanohydrogel coating and its ability to prevent microbial adhesion under drinking water conditions. Stability was assessed through detailed scanning electron microscopy, atomic force microscopy, and contact angle measurements after accelerated stress tests under different physicochemical conditions, including temperature, pH, salt concentration, and surfactant concentration. Microbial adhesion was tested in 35 day long recirculation experiments performed in a lab-scale DWDS under relevant drinking water conditions. The coating exhibited a very high stability under harsh pH conditions (1.5-13.5), high and low temperatures (4-70 °C) and extreme salt concentrations (0.1-6000 mM). However, at high surfactant concentrations, above the critical micellar concentration, some instability was observed. Against DWDS conditions, the coating remained stable over 35 days, showing a significant reduction (>80%) in adhesion of microorganisms. Overall, these findings support the use of the PNIPAM nanohydrogel coating as a scalable and stable solution to microbial adhesion in drinking water environments, offering a promising alternative or support to disinfection treatments to reduce biofilm formation in DWDS systems but with high potential toward other applications due to the highly stable nature of the nanohydrogel coating.
- 5 February 2026
- Published by American Chemical Society (ACS) in ACS Applied Engineering Materials
- Vol. 4 (2) , 650-660
Poly( N -isopropylmethacrylamide) Nanohydrogel Coatings to Limit the Adhesion of Microorganisms in Drinking Water Distribution Systems: Stability and Optimization
Biofilm formation in drinking water distribution systems (DWDSs) presents a significant challenge, compromising both water quality and infrastructure lifetime. Recently, a nanohydrogel coating was demonstrated to have excellent antiadhesive properties toward drinking water microorganisms, making it a promising approach to alleviate biofilm formation in DWDS systems. However, the used coating procedure was not suitable for large surface areas and the stability of the coating under various physicochemical conditions was not assessed. This study proposes an optimized coating procedure for poly-(vinyl chloride) (PVC)-based drinking water piping and evaluates the stability of this poly-(N-isopropylmethacrylamide) (PNIPAM) based nanohydrogel coating and its ability to prevent microbial adhesion under drinking water conditions. Stability was assessed through detailed scanning electron microscopy, atomic force microscopy, and contact angle measurements after accelerated stress tests under different physicochemical conditions, including temperature, pH, salt concentration, and surfactant concentration. Microbial adhesion was tested in 35 day long recirculation experiments performed in a lab-scale DWDS under relevant drinking water conditions. The coating exhibited a very high stability under harsh pH conditions (1.5-13.5), high and low temperatures (4-70 °C) and extreme salt concentrations (0.1-6000 mM). However, at high surfactant concentrations, above the critical micellar concentration, some instability was observed. Against DWDS conditions, the coating remained stable over 35 days, showing a significant reduction (>80%) in adhesion of microorganisms. Overall, these findings support the use of the PNIPAM nanohydrogel coating as a scalable and stable solution to microbial adhesion in drinking water environments, offering a promising alternative or support to disinfection treatments to reduce biofilm formation in DWDS systems but with high potential toward other applications due to the highly stable nature of the nanohydrogel coating.
- Open Access
- 11 November 2025
- Published by Elsevier in Water Research
- Vol. 289 (Pt B) , 124941
Investigating the role of physicochemical surface properties of polymeric pipe materials and a nanogel-based coating on microbial adhesion in unchlorinated drinking water
- 11 November 2025
- Published by Elsevier in Water Research
- Vol. 289 (Pt B) , 124941
Open AccessInvestigating the role of physicochemical surface properties of polymeric pipe materials and a nanogel-based coating on microbial adhesion in unchlorinated drinking water
- 2 September 2024
- Published by Royal Society of Chemistry (RSC) in Environmental Science: Water Research & Technology
- Vol. 10 (11) , 2844-2857
Production of birnessite-type manganese oxides by biofilms from oxygen-supplemented biological activated carbon (BAC) filters
Biological oxidation of manganese (Mn) by bacteria results in the formation of biogenic Mn oxides (MnOx), which are known to be strong oxidants and effective catalysts. Manganese-oxidizing bacteria (MnOB) often develop in engineered systems for water treatment under oligotrophic conditions. In this study, we investigated the MnOB within biofilms sampled in two different seasons from full-scale oxygen-supplemented biological activated carbon (BAC) filters performing the complete removal of Mn from wastewater. By applying a novel batch enrichment approach ensuring the continuous presence of soluble Mn, after 42 days the start-up microbial community grew into thick, floccular biofilms efficiently oxidizing Mn2+ into numerous black nodules. The amount of Mn oxidized was quantified using inductively coupled plasma optical emission spectroscopy (ICP-OES). X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM) revealed that the MnOx formed was a birnessite-type (δ-MnO2) with a crystalline, nanoflower structure. Comparison of the microbial community composition before and after the enrichment by means of 16S rRNA gene amplicon sequencing showed increases of members of the orders Rhizobiales and Burkholderiales, and identified among the most abundant some bacterial groups which have rarely or never been associated with Mn oxidation before (Rhodococcus, Ellin6067, Planctomycetota Pir4 lineage, Rhizobiales A0839 and Amb-16S-1323). This study unravels the potential of production of crystalline MnOx by mixed-microbial communities which uniquely generate in a man-made biofilter. The new insights provided implement the knowledge in the field, with the perspective to design innovative biotechnologies to remove recalcitrant compounds where MnOB find optimal growth conditions to produce catalytic forms of MnOx.
- 2 September 2024
- Published by Royal Society of Chemistry (RSC) in Environmental Science: Water Research & Technology
- Vol. 10 (11) , 2844-2857
Production of birnessite-type manganese oxides by biofilms from oxygen-supplemented biological activated carbon (BAC) filters
Biological oxidation of manganese (Mn) by bacteria results in the formation of biogenic Mn oxides (MnOx), which are known to be strong oxidants and effective catalysts. Manganese-oxidizing bacteria (MnOB) often develop in engineered systems for water treatment under oligotrophic conditions. In this study, we investigated the MnOB within biofilms sampled in two different seasons from full-scale oxygen-supplemented biological activated carbon (BAC) filters performing the complete removal of Mn from wastewater. By applying a novel batch enrichment approach ensuring the continuous presence of soluble Mn, after 42 days the start-up microbial community grew into thick, floccular biofilms efficiently oxidizing Mn2+ into numerous black nodules. The amount of Mn oxidized was quantified using inductively coupled plasma optical emission spectroscopy (ICP-OES). X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM) revealed that the MnOx formed was a birnessite-type (δ-MnO2) with a crystalline, nanoflower structure. Comparison of the microbial community composition before and after the enrichment by means of 16S rRNA gene amplicon sequencing showed increases of members of the orders Rhizobiales and Burkholderiales, and identified among the most abundant some bacterial groups which have rarely or never been associated with Mn oxidation before (Rhodococcus, Ellin6067, Planctomycetota Pir4 lineage, Rhizobiales A0839 and Amb-16S-1323). This study unravels the potential of production of crystalline MnOx by mixed-microbial communities which uniquely generate in a man-made biofilter. The new insights provided implement the knowledge in the field, with the perspective to design innovative biotechnologies to remove recalcitrant compounds where MnOB find optimal growth conditions to produce catalytic forms of MnOx.
- Open Access
- 19 January 2024
- Published by Elsevier in Process Safety and Environmental Protection
- Vol. 183, 687-697
Effects of food to inoculum ratio and ultrasound pre-treatment on biogas production from dissolved air flotation waste from dairy industry
- 19 January 2024
- Published by Elsevier in Process Safety and Environmental Protection
- Vol. 183, 687-697
Open AccessEffects of food to inoculum ratio and ultrasound pre-treatment on biogas production from dissolved air flotation waste from dairy industry
- Open Access
- 7 February 2023
- Published by Taylor & Francis in Biofouling
- Vol. 39 (2) , 121-134
Nanogel-based coating as an alternative strategy for biofilm control in drinking water distribution systems
Biofilm formation and detachment in drinking water distribution systems (DWDS) can lead to several operational issues. Here, an alternative biofilm control strategy of limiting bacterial adhesion by application of a poly(N-isopropylmethacrylamide)-based nanogel coating on DWDS pipe walls was investigated. The nanogel coatings were successfully deposited on surfaces of four polymeric pipe materials commonly applied in DWDS construction. Nanogel-coated and non-coated pipe materials were characterized in terms of their surface hydrophilicity and roughness. Four DWDS relevant bacterial strains, representing Sphingomonas and Pseudomonas, were used to evaluate the anti-adhesive performance of the coating in 4 h adhesion and 24 h biofilm assays. The presence of the nanogel coating resulted in adhesion reduction up to 97%, and biofilm reduction up to 98%, compared to non-coated surfaces. These promising results motivate further investigation of nanogel coatings as a strategy for biofilm prevention in DWDS. Graphical Abstract
- 7 February 2023
- Published by Taylor & Francis in Biofouling
- Vol. 39 (2) , 121-134
Open AccessNanogel-based coating as an alternative strategy for biofilm control in drinking water distribution systems
Biofilm formation and detachment in drinking water distribution systems (DWDS) can lead to several operational issues. Here, an alternative biofilm control strategy of limiting bacterial adhesion by application of a poly(N-isopropylmethacrylamide)-based nanogel coating on DWDS pipe walls was investigated. The nanogel coatings were successfully deposited on surfaces of four polymeric pipe materials commonly applied in DWDS construction. Nanogel-coated and non-coated pipe materials were characterized in terms of their surface hydrophilicity and roughness. Four DWDS relevant bacterial strains, representing Sphingomonas and Pseudomonas, were used to evaluate the anti-adhesive performance of the coating in 4 h adhesion and 24 h biofilm assays. The presence of the nanogel coating resulted in adhesion reduction up to 97%, and biofilm reduction up to 98%, compared to non-coated surfaces. These promising results motivate further investigation of nanogel coatings as a strategy for biofilm prevention in DWDS. Graphical Abstract
- Open Access
- 24 May 2022
- Published by American Society for Microbiology in Applied and Environmental Microbiology
- Vol. 88 (10) , e0244921
Functional Insights of Salinity Stress-Related Pathways in Metagenome-Resolved Methanothrix Genomes
Using genome-centric metagenomics, we discovered a new Methanothrix harundinacea subspecies that appears to be a halotolerant acetoclastic methanogen with the flexibility for adaptation in the anaerobic digestion process both at low (5 g/L Na + ) and high salinity conditions (20 g/L Na + ). Annotation of the recovered M. harundinacea genome revealed salinity stress-related functions, including the modification of EPS glycoconjugates and the production of compatible solutes.
- 24 May 2022
- Published by American Society for Microbiology in Applied and Environmental Microbiology
- Vol. 88 (10) , e0244921
Open AccessFunctional Insights of Salinity Stress-Related Pathways in Metagenome-Resolved Methanothrix Genomes
Using genome-centric metagenomics, we discovered a new Methanothrix harundinacea subspecies that appears to be a halotolerant acetoclastic methanogen with the flexibility for adaptation in the anaerobic digestion process both at low (5 g/L Na + ) and high salinity conditions (20 g/L Na + ). Annotation of the recovered M. harundinacea genome revealed salinity stress-related functions, including the modification of EPS glycoconjugates and the production of compatible solutes.