Iván Lombardero
Research Subjects
Iván Lombardero has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Carlos Algora
Instituto de Energía Solar, Universidad Politécnica de Madrid, Avda. Complutense, 30, 28040 Madrid, Spain
10 shared publications - Mercedes Gabas
Universidad de Málaga, Andalucía Tech, Departamento de Física Aplicada I, The Nanotech Unit, Campus de Teatinos, s/n, 29071 Málaga, Spain
6 shared publications - Ignacio Rey-Stolle
Instituto de Energía Solar, ETSI de Telecomunicación, Universidad Politécnica de Madrid, 28040 Madrid, Spain
5 shared publications - Iván García
Universidad Politécnica de Madrid
5 shared publications - Mario Ochoa
Photonics Engineering Group, University of Cantabria, 39005 Santander, Spain
4 shared publications - Neftali Nuñez
Escuela Técnica superior de Ingeniería y Sistemas de Telecomunicación, Universidad Politécnica de Madrid, 28031 Madrid, Spain
3 shared publications
Latest Publications
- 2 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
High Temperature Accelerated Life Tests for GaInP/GaAs/Ge Solar Cells: Forward Versus Forward-Reverse Bias
This paper presents the comparison of two temperature Accelerated Life Tests (ALTs) for space commercial solar cells. The tests are carried out in dark conditions to circumvent the inherent problems of illumination ALTs. In the first ALT the solar cell working conditions were emulated by means of forward bias (that emulates the electric performance under illumination) while in the second ALT, forward bias was used together with reverse bias (that emulates the shadowing at eclipse periods or any other shadowing event such as for example the shadows cast by antennas) in order to reproduce more adequately the real operation conditions of solar cells. Forward to reverse time ratio is 4:1. Furthermore, the high temperatures used in the second ALT (190, 210 and 230 °C) allow a considerable time reduction of the test with respect to the first ALT (150, 165 and 180°C). The evaluation of the Arrhenius activation energy for an illumination power degradation of 10% was 0.88 eV in the forward bias test while 1.06 eV in the forward-reverse test. Reverse bias promotes similar degradation mode than forward one, namely parallel resistance reduction, but probably with a different degradation mechanism that degrades solar cell more intensely, thus reducing reliability which is more than 7 times shorter in the forward-reverse test than in forward one. Despite this reliability reduction, the time for a 90% reliability in the forward-reverse ALT is 32 years of continuous operation assuming a nominal temperature of 80°C which is typical of many GEO missions. The solar cells used in both ALTs were commercial GaInP/Ga(In)As/Ge triple junction and perform very robustly and exhibiting a high reliability for many space applications. It should be noted that these reliability figures are related to the degradation caused exclusively by high temperatures and other stressors like radiation are not considered here.
- 2 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
High Temperature Accelerated Life Tests for GaInP/GaAs/Ge Solar Cells: Forward Versus Forward-Reverse Bias
This paper presents the comparison of two temperature Accelerated Life Tests (ALTs) for space commercial solar cells. The tests are carried out in dark conditions to circumvent the inherent problems of illumination ALTs. In the first ALT the solar cell working conditions were emulated by means of forward bias (that emulates the electric performance under illumination) while in the second ALT, forward bias was used together with reverse bias (that emulates the shadowing at eclipse periods or any other shadowing event such as for example the shadows cast by antennas) in order to reproduce more adequately the real operation conditions of solar cells. Forward to reverse time ratio is 4:1. Furthermore, the high temperatures used in the second ALT (190, 210 and 230 °C) allow a considerable time reduction of the test with respect to the first ALT (150, 165 and 180°C). The evaluation of the Arrhenius activation energy for an illumination power degradation of 10% was 0.88 eV in the forward bias test while 1.06 eV in the forward-reverse test. Reverse bias promotes similar degradation mode than forward one, namely parallel resistance reduction, but probably with a different degradation mechanism that degrades solar cell more intensely, thus reducing reliability which is more than 7 times shorter in the forward-reverse test than in forward one. Despite this reliability reduction, the time for a 90% reliability in the forward-reverse ALT is 32 years of continuous operation assuming a nominal temperature of 80°C which is typical of many GEO missions. The solar cells used in both ALTs were commercial GaInP/Ga(In)As/Ge triple junction and perform very robustly and exhibiting a high reliability for many space applications. It should be noted that these reliability figures are related to the degradation caused exclusively by high temperatures and other stressors like radiation are not considered here.
- 11 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Advances in Flexible and Lightweight III-V Multijunction Solar Cells for High Power Density Applications
We are developing flexible and lightweight III-V multijuntion solar cells for high power density applications such as unmanned aerial vehicles (drones), High Altitude Pseudo Satellites (HAPS) and high altitude stratospheric balloons for satellite-like communications, cheap and widespread internet connectivity, etc. We focus our research on two different types of III-V solar cells covering the range from 1 kW/kg to 3 kW/kg (considering the weight of the solar cell itself and not that of the module). Our approach to achieve a goal of 3 kW/kg is based on 3J inverted metamorphic solar cells. We have recently developed GaInP/GaAs/GaInAs 3J IMM solar cells with a power density of 5.7 kW/kg under 1xAM1.5g for small areas. Demonstrating large area devices (tens of square cm) is the next challenge to tackle. In addition, we are developing lower-cost designs, targeting 1 kW/kg, based on GaInP/Ga(In)As/Ge 3J lattice matched solar cells. In this paper we present the advances in the modelling and manufacturing of this last type of solar cell. Modelling indicates that there are multiple efficiency-thickness combinations reaching the 1 kW/kg target. For example in the case of AM1.5g, a solar thickness of 46 microns requires an efficiency of 30% which is a demanding value. However, if the thickness is reduced to 40 microns, a more easily achievable efficiency of 27% would be required. We have demonstrated a process for thinning the Ge substrates reaching thicknesses as low as 14 microns with highly homogeneous thickness profiles. Preliminary results show that the 3J thinned solar cell exhibits an efficiency which is the 91% of the efficiency achieved by the non-thinned cell.
- 11 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Advances in Flexible and Lightweight III-V Multijunction Solar Cells for High Power Density Applications
We are developing flexible and lightweight III-V multijuntion solar cells for high power density applications such as unmanned aerial vehicles (drones), High Altitude Pseudo Satellites (HAPS) and high altitude stratospheric balloons for satellite-like communications, cheap and widespread internet connectivity, etc. We focus our research on two different types of III-V solar cells covering the range from 1 kW/kg to 3 kW/kg (considering the weight of the solar cell itself and not that of the module). Our approach to achieve a goal of 3 kW/kg is based on 3J inverted metamorphic solar cells. We have recently developed GaInP/GaAs/GaInAs 3J IMM solar cells with a power density of 5.7 kW/kg under 1xAM1.5g for small areas. Demonstrating large area devices (tens of square cm) is the next challenge to tackle. In addition, we are developing lower-cost designs, targeting 1 kW/kg, based on GaInP/Ga(In)As/Ge 3J lattice matched solar cells. In this paper we present the advances in the modelling and manufacturing of this last type of solar cell. Modelling indicates that there are multiple efficiency-thickness combinations reaching the 1 kW/kg target. For example in the case of AM1.5g, a solar thickness of 46 microns requires an efficiency of 30% which is a demanding value. However, if the thickness is reduced to 40 microns, a more easily achievable efficiency of 27% would be required. We have demonstrated a process for thinning the Ge substrates reaching thicknesses as low as 14 microns with highly homogeneous thickness profiles. Preliminary results show that the 3J thinned solar cell exhibits an efficiency which is the 91% of the efficiency achieved by the non-thinned cell.
- 8 March 2022
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 30 (7) , 740-749
Manufacturing process for III–V multijunction solar cells on germanium substrates with a total thickness below 60 microns
In this work, we demonstrate a new manufacturing process that allows to fabricate thin solar cells avoiding problems related to the brittleness or fragility of thin wafers without needing any carrier nor temporary substrate. This technique has been successfully applied to Ge single and GaInP/Ga(In)As/Ge triple‐junction solar cells grown on Ge substrates, achieving 47.5‐ and 55.5‐μm‐thick substrates, respectively. Although this technique should allow to thin substrates to any desired thickness, a final thickness around 20–30 μm is recommended due to practical concerns such as the uneven substrate thickness throughout the wafer. In any case, a III–V solar cell with such a thickness should be thin enough for most applications and, in particular, for space ones.
- 8 March 2022
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 30 (7) , 740-749
Manufacturing process for III–V multijunction solar cells on germanium substrates with a total thickness below 60 microns
In this work, we demonstrate a new manufacturing process that allows to fabricate thin solar cells avoiding problems related to the brittleness or fragility of thin wafers without needing any carrier nor temporary substrate. This technique has been successfully applied to Ge single and GaInP/Ga(In)As/Ge triple‐junction solar cells grown on Ge substrates, achieving 47.5‐ and 55.5‐μm‐thick substrates, respectively. Although this technique should allow to thin substrates to any desired thickness, a final thickness around 20–30 μm is recommended due to practical concerns such as the uneven substrate thickness throughout the wafer. In any case, a III–V solar cell with such a thickness should be thin enough for most applications and, in particular, for space ones.
- Open Access
Analysis of Current Transport Mechanism in AP-MOVPE Grown GaAsN p-i-n Solar Cell
Basic knowledge about the factors and mechanisms affecting the performance of solar cells and their identification is essential when thinking of future improvements to the device. Within this paper, we investigated the current transport mechanism in GaAsN p-i-n solar cells grown with atmospheric pressure metal organic vapour phase epitaxy (AP-MOVPE). We examined the electro-optical and structural properties of a GaAsN solar cell epitaxial structure and correlated the results with temperature-dependent current-voltage measurements and deep level transient spectroscopy findings. The analysis of J-V-T measurements carried out in a wide temperature range allows for the determination of the dominant current transport mechanism in a GaAsN-based solar cell device and assign it a nitrogen interstitial defect, the presence of which was confirmed by DLTFS investigation.
Open AccessAnalysis of Current Transport Mechanism in AP-MOVPE Grown GaAsN p-i-n Solar Cell
Basic knowledge about the factors and mechanisms affecting the performance of solar cells and their identification is essential when thinking of future improvements to the device. Within this paper, we investigated the current transport mechanism in GaAsN p-i-n solar cells grown with atmospheric pressure metal organic vapour phase epitaxy (AP-MOVPE). We examined the electro-optical and structural properties of a GaAsN solar cell epitaxial structure and correlated the results with temperature-dependent current-voltage measurements and deep level transient spectroscopy findings. The analysis of J-V-T measurements carried out in a wide temperature range allows for the determination of the dominant current transport mechanism in a GaAsN-based solar cell device and assign it a nitrogen interstitial defect, the presence of which was confirmed by DLTFS investigation.
- Open Access
- 29 July 2020
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 28 (11) , 1097-1106
Theoretical and experimental assessment of thinned germanium substrates for III–V multijunction solar cells
Solar cells manufactured on top of Ge substrates suffer from inherent drawbacks that hinder or limit their potential. The most deleterious ones are heavy weight, high bulk recombination, lack of photon confinement, and an increase of the heat absorption. The use of thinned Ge substrates is herein proposed as a possible solution to the aforementioned challenges. The potential of a thinned Ge subcell inside a standard GaInP/Ga(In)As/Ge triple‐junction solar cell is assessed by simulations, pointing to an optimum thickness around 5–10 μm. This would reduce the weight by more than 90%, whereas the available current for the Ge subcell would decrease only by 5%. In addition, the heat absorption for wavelengths beyond 1600 nm would decrease by more than 85%. The performance of such a device is highly influenced by the front and back surface recombination of the p–n junction. Simulations remark that good back surface passivation is mandatory to avoid losing power generation by thinning the substrate. In contrast, it has been found that front surface recombination lowers the power generation in a similar manner for thin and thick solar cells. Therefore, the benefits of thinning the substrate are not limited by the front surface recombination. Finally, Ge single‐junction solar cells thinned down to 85 μm by wet etching processes are demonstrated. The feasibility of the thinning process is supported by the limited losses measured in the current generation (less than 6%) and generated voltage (4%) for the thinnest solar cell manufactured.
- 29 July 2020
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 28 (11) , 1097-1106
Open AccessTheoretical and experimental assessment of thinned germanium substrates for III–V multijunction solar cells
Solar cells manufactured on top of Ge substrates suffer from inherent drawbacks that hinder or limit their potential. The most deleterious ones are heavy weight, high bulk recombination, lack of photon confinement, and an increase of the heat absorption. The use of thinned Ge substrates is herein proposed as a possible solution to the aforementioned challenges. The potential of a thinned Ge subcell inside a standard GaInP/Ga(In)As/Ge triple‐junction solar cell is assessed by simulations, pointing to an optimum thickness around 5–10 μm. This would reduce the weight by more than 90%, whereas the available current for the Ge subcell would decrease only by 5%. In addition, the heat absorption for wavelengths beyond 1600 nm would decrease by more than 85%. The performance of such a device is highly influenced by the front and back surface recombination of the p–n junction. Simulations remark that good back surface passivation is mandatory to avoid losing power generation by thinning the substrate. In contrast, it has been found that front surface recombination lowers the power generation in a similar manner for thin and thick solar cells. Therefore, the benefits of thinning the substrate are not limited by the front surface recombination. Finally, Ge single‐junction solar cells thinned down to 85 μm by wet etching processes are demonstrated. The feasibility of the thinning process is supported by the limited losses measured in the current generation (less than 6%) and generated voltage (4%) for the thinnest solar cell manufactured.
- 19 November 2019
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 28 (2) , 148-166
Temperature Accelerated Life Test and Failure Analysis on Upright Metamorphic Ga0.37In0.63P/Ga0.83In0.17As/Ge Triple Junction Solar Cells
A temperature accelerated life test on Upright Metamorphic Ga0.37In0.63P/Ga0.83In0.17As/Ge triple‐junction solar cells has been carried out. The acceleration has been accomplished by subjecting the solar cells to temperatures (125, 145 and 165°C) significantly higher than the nominal working temperature inside a concentrator (90°C), while the nominal photo‐current (500×) has been emulated by injecting current in darkness. The failure distributions have been fitted to an Arrhenius–Weibull model resulting in an activation energy of 1.39 eV. Accordingly, a 72 years warranty time for those solar cells for a place like Tucson (AZ, USA), was determined. After the ALT, an intense characterization campaign has been carried out in order to determine the failure origin. We have detected that temperature soak alone is enough to degrade the cell performance by increasing the leakage currents, the series resistance, and the recombination currents. When solar cells were also forward biased an increase of series resistance together with a reduction of short circuit current is detected. The failure analysis shows that: a) several metallization sub‐products concentrate in several regions of front metal grid where they poison the silver, resulting in a two times reduction of the metal sheet resistance; b) the metal/cap layer interface is greatly degraded and there is also a deterioration of the cap layer crystalline quality producing a huge increase of the specific front contact resistance, c) the decrease of short circuit current is mainly due to the GaInP top subcell degradation.
- 19 November 2019
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 28 (2) , 148-166
Temperature Accelerated Life Test and Failure Analysis on Upright Metamorphic Ga0.37In0.63P/Ga0.83In0.17As/Ge Triple Junction Solar Cells
A temperature accelerated life test on Upright Metamorphic Ga0.37In0.63P/Ga0.83In0.17As/Ge triple‐junction solar cells has been carried out. The acceleration has been accomplished by subjecting the solar cells to temperatures (125, 145 and 165°C) significantly higher than the nominal working temperature inside a concentrator (90°C), while the nominal photo‐current (500×) has been emulated by injecting current in darkness. The failure distributions have been fitted to an Arrhenius–Weibull model resulting in an activation energy of 1.39 eV. Accordingly, a 72 years warranty time for those solar cells for a place like Tucson (AZ, USA), was determined. After the ALT, an intense characterization campaign has been carried out in order to determine the failure origin. We have detected that temperature soak alone is enough to degrade the cell performance by increasing the leakage currents, the series resistance, and the recombination currents. When solar cells were also forward biased an increase of series resistance together with a reduction of short circuit current is detected. The failure analysis shows that: a) several metallization sub‐products concentrate in several regions of front metal grid where they poison the silver, resulting in a two times reduction of the metal sheet resistance; b) the metal/cap layer interface is greatly degraded and there is also a deterioration of the cap layer crystalline quality producing a huge increase of the specific front contact resistance, c) the decrease of short circuit current is mainly due to the GaInP top subcell degradation.
- 3 November 2019
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 28 (1) , 60-70
On the use of graphene to improve the performance of concentrator III‐V multijunction solar cells
Graphene has been intensively studied in photovoltaics focusing on emerging solar cells based on thin films, dye‐sensitized solar cells, quantum dots, nanowires, and so forth. However, the typical efficiency of these solar cells incorporating graphene is below 16%. Therefore, the photovoltaic potential of graphene has not yet been shown. In this work, the use of graphene for concentration applications on III‐V multijunction solar cells, which indeed are the solar cells with the highest efficiency, is demonstrated. First, a wide optoelectronic characterization of graphene layers is carried out. Then, the graphene layer is incorporated onto triple‐junction solar cells, which decreases their series resistance by 35% (relative), leading to an increase in fill factor of 4% (absolute) at concentrations of 1000 suns. Simultaneously, the optical absorption of graphene produces a relative short‐circuit current density decrease in the range of 0% to 1.8%. As a result, an absolute efficiency improvement close to 1% at concentrations of 1000 suns was achieved with respect to triple‐junction solar cells without graphene. The impact of incorporating one and two graphene monolayers is also evaluated.
- 3 November 2019
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 28 (1) , 60-70
On the use of graphene to improve the performance of concentrator III‐V multijunction solar cells
Graphene has been intensively studied in photovoltaics focusing on emerging solar cells based on thin films, dye‐sensitized solar cells, quantum dots, nanowires, and so forth. However, the typical efficiency of these solar cells incorporating graphene is below 16%. Therefore, the photovoltaic potential of graphene has not yet been shown. In this work, the use of graphene for concentration applications on III‐V multijunction solar cells, which indeed are the solar cells with the highest efficiency, is demonstrated. First, a wide optoelectronic characterization of graphene layers is carried out. Then, the graphene layer is incorporated onto triple‐junction solar cells, which decreases their series resistance by 35% (relative), leading to an increase in fill factor of 4% (absolute) at concentrations of 1000 suns. Simultaneously, the optical absorption of graphene produces a relative short‐circuit current density decrease in the range of 0% to 1.8%. As a result, an absolute efficiency improvement close to 1% at concentrations of 1000 suns was achieved with respect to triple‐junction solar cells without graphene. The impact of incorporating one and two graphene monolayers is also evaluated.
- 19 June 2019
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 27 (9) , 789-797
Enhanced performance of GaInP/GaAs/Ge solar cells under high concentration through Pd/Ge/Ti/Pd/Al grid metallization
Series resistance is the key limiting factor that constrains the electrical performance of solar cells under ultra‐high concentration. Typically, the most critical component of the series resistance is that stemming from the front contact, and therefore, the formation of front metal grids with low metal–semiconductor specific contact resistance and low metal sheet resistance is vital for high concentrator solar cells. Consequently, in this study, a novel Pd/Ge/Ti/Pd/Al metal stack has been proposed and implemented on a GaInP/GaAs/Ge triple junction solar cell. This system exhibits low metal resistivity due to the middle Ti/Pd barrier layer hindering the diffusion and contamination between the GaAs semiconductor and top conductive metal layer, and very low specific contact resistance because of the Pd/Ge layer forming an interfacial layer with the GaAs cap which increases the electron tunneling probability. As a result, the fill factor of the solar cell remains almost constant and close to 90% in the 250× to 1500× range, while efficiency keeps on increasing even at the maximum concentration measured of 1500×. Its performance and cost‐effectiveness make this contact a compelling solution to extend solar cell operation in the ultra‐high concentration regime.
- 19 June 2019
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 27 (9) , 789-797
Enhanced performance of GaInP/GaAs/Ge solar cells under high concentration through Pd/Ge/Ti/Pd/Al grid metallization
Series resistance is the key limiting factor that constrains the electrical performance of solar cells under ultra‐high concentration. Typically, the most critical component of the series resistance is that stemming from the front contact, and therefore, the formation of front metal grids with low metal–semiconductor specific contact resistance and low metal sheet resistance is vital for high concentrator solar cells. Consequently, in this study, a novel Pd/Ge/Ti/Pd/Al metal stack has been proposed and implemented on a GaInP/GaAs/Ge triple junction solar cell. This system exhibits low metal resistivity due to the middle Ti/Pd barrier layer hindering the diffusion and contamination between the GaAs semiconductor and top conductive metal layer, and very low specific contact resistance because of the Pd/Ge layer forming an interfacial layer with the GaAs cap which increases the electron tunneling probability. As a result, the fill factor of the solar cell remains almost constant and close to 90% in the 250× to 1500× range, while efficiency keeps on increasing even at the maximum concentration measured of 1500×. Its performance and cost‐effectiveness make this contact a compelling solution to extend solar cell operation in the ultra‐high concentration regime.
- 13 September 2018
- Published by AIP Publishing
- Vol. 2012 (1) , 040008
Lowering perimeter recombination losses in micro-concentrator solar cells: A simulation study
A device simulation study regarding perimeter recombination losses in micro-concentrator solar cells is presented. Perimeter losses for traditional and heterojunction designs were computed under dark and illuminated conditions for different solar cell sizes and surface state densities. A 2D device simulation model based on SRH recombination has shown that the use of heterojunction designs could help mitigate perimeter recombination for micro-CPV solar cells.
- 13 September 2018
- Published by AIP Publishing
- Vol. 2012 (1) , 040008
Lowering perimeter recombination losses in micro-concentrator solar cells: A simulation study
A device simulation study regarding perimeter recombination losses in micro-concentrator solar cells is presented. Perimeter losses for traditional and heterojunction designs were computed under dark and illuminated conditions for different solar cell sizes and surface state densities. A 2D device simulation model based on SRH recombination has shown that the use of heterojunction designs could help mitigate perimeter recombination for micro-CPV solar cells.