Beatriz Garcia Vasallo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Beatriz Garcia Vasallo has a total of 103 co-authors. Here are the top co-authors by number of shared publications:
- Tomas Gonzalez
Applied Physics Department and USAL-NANOLAB, Universidad de Salamanca, Salamanca, Spain
50 shared publications - Javier Mateos
Applied Physics Department and USAL-NANOLAB, Universidad de Salamanca, Salamanca, Spain
31 shared publications D. Pardo
Universidad de Salamanca, Plaza de la Merced, s/n, 37008, Salamanca, Spain
15 shared publicationsJ. Mateos
Dept. Fisica Aplicada, Universidad de Salamanca, Spain
15 shared publications- Alain Cappy
Centre National de la Recherche Scientifique
12 shared publications - Susana Perez
Applied Physics Department and NANOLAB USAL, Universidad de Salamanca, Plaza de la Merced s/n, 37008 Salamanca, Spain
11 shared publications
Latest Publications
- Open Access
- 24 December 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (1) , 015104
Physical analysis of barrier-inhomogeneity effects on the electrical parameters of GaN Schottky barrier diodes
The influence on current–voltage and capacitance-voltage characteristics of different inhomogeneous profiles for the energy barrier ( ϕ B ) along the Schottky contact of GaN Schottky barrier diodes is studied by means of a home-made Monte Carlo simulator. An insight analysis of the electron concentration and electric field inside the device allows explaining the strong influence of inhomogeneities on the electronic transport across the metal semiconductor interface. In reverse bias, the low-barrier regions increase the number of tunneled electrons and these carriers tend to move towards the surrounded low populated zones inside the semiconductor. Therefore, two-dimensional effects appear and the current flowing through the device depends not only on the value and area of the low-barrier regions but also on its relative location. On the contrary, the potential profile is not affected much by low-barrier inhomogeneities, since they are pinched-off by the surrounding high-barrier zones. As a consequence, the effective ϕ B obtained from the C–V characteristics essentially corresponds to the (high-barrier) nominal ϕ B , while the effective ϕ B obtained from forward I–V characteristics is strongly impacted by the low-barrier regions. In the latter case, lower effective values of the barrier are obtained together with an increase in the ideality factor. These effects connect the physical performance of these devices with the effective ϕ B measured in fabricated ones.
- 24 December 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (1) , 015104
Open AccessPhysical analysis of barrier-inhomogeneity effects on the electrical parameters of GaN Schottky barrier diodes
The influence on current–voltage and capacitance-voltage characteristics of different inhomogeneous profiles for the energy barrier ( ϕ B ) along the Schottky contact of GaN Schottky barrier diodes is studied by means of a home-made Monte Carlo simulator. An insight analysis of the electron concentration and electric field inside the device allows explaining the strong influence of inhomogeneities on the electronic transport across the metal semiconductor interface. In reverse bias, the low-barrier regions increase the number of tunneled electrons and these carriers tend to move towards the surrounded low populated zones inside the semiconductor. Therefore, two-dimensional effects appear and the current flowing through the device depends not only on the value and area of the low-barrier regions but also on its relative location. On the contrary, the potential profile is not affected much by low-barrier inhomogeneities, since they are pinched-off by the surrounding high-barrier zones. As a consequence, the effective ϕ B obtained from the C–V characteristics essentially corresponds to the (high-barrier) nominal ϕ B , while the effective ϕ B obtained from forward I–V characteristics is strongly impacted by the low-barrier regions. In the latter case, lower effective values of the barrier are obtained together with an increase in the ideality factor. These effects connect the physical performance of these devices with the effective ϕ B measured in fabricated ones.
- 14 October 2024
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (1) , 015112
Avoiding avalanche breakdown in planar GaN Gunn diodes by means of a substrate contact
Impact ionization originated by the buffer leakage current, together with high electric fields ( > 3 MV cm−1) at the anode corner of the isolating trenches, has been identified as the failure mechanism of shaped planar GaN Gunn diodes when biased above 20 V, so that no evidence of Gunn oscillations in fabricated devices has been observed yet. In order to avoid the avalanche, we propose the addition of a Schottky substrate terminal, which, by means of Monte Carlo simulations, has been confirmed to be able to suppress such not-desired leakage current when applying a negative substrate bias. When the substrate bias is positive, impact ionization is also reduced due to the lower electric field at the hotspot, but a vertical cathode-substrate current degrades the device operation. In order to avoid such current, we propose the use a MIS configuration for the substrate contact, which is the optimal solution.
- 14 October 2024
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (1) , 015112
Avoiding avalanche breakdown in planar GaN Gunn diodes by means of a substrate contact
Impact ionization originated by the buffer leakage current, together with high electric fields ( > 3 MV cm−1) at the anode corner of the isolating trenches, has been identified as the failure mechanism of shaped planar GaN Gunn diodes when biased above 20 V, so that no evidence of Gunn oscillations in fabricated devices has been observed yet. In order to avoid the avalanche, we propose the addition of a Schottky substrate terminal, which, by means of Monte Carlo simulations, has been confirmed to be able to suppress such not-desired leakage current when applying a negative substrate bias. When the substrate bias is positive, impact ionization is also reduced due to the lower electric field at the hotspot, but a vertical cathode-substrate current degrades the device operation. In order to avoid such current, we propose the use a MIS configuration for the substrate contact, which is the optimal solution.
- 11 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (8) , 4524-4529
Reverse Leakage Current Hysteresis in GaN Schottky Barrier Diodes Interpreted in Terms of a Trap Energy Band
The hysteresis cycles observed in the reverse leakage current measured at low temperatures in GaN-on-sapphire Schottky barrier diodes (SBDs) have been deeply studied and interpreted in terms of trap-assisted tunneling (TAT) compatible with the existence of a trap energy band (TEB) near the metal-semiconductor interface. The analysis of the energies for which the maximum tunneling current occurs, both direct and through this trap band, allows us to explain the behaviors found at different temperatures. Starting from empty trap states by previous illumination, transient current measurements performed under different preconditioning voltages evidence a progressive partial filling/release of the trap energy levels, confirmed as well by pulsed measurements. Captured/released electrons modify the number of trap states available for tunneling and thus the current level. As a consequence, tunneling processes in the go and return paths take place through levels with different occupations within the TEB, originating the hysteresis cycle.
- 11 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (8) , 4524-4529
Reverse Leakage Current Hysteresis in GaN Schottky Barrier Diodes Interpreted in Terms of a Trap Energy Band
The hysteresis cycles observed in the reverse leakage current measured at low temperatures in GaN-on-sapphire Schottky barrier diodes (SBDs) have been deeply studied and interpreted in terms of trap-assisted tunneling (TAT) compatible with the existence of a trap energy band (TEB) near the metal-semiconductor interface. The analysis of the energies for which the maximum tunneling current occurs, both direct and through this trap band, allows us to explain the behaviors found at different temperatures. Starting from empty trap states by previous illumination, transient current measurements performed under different preconditioning voltages evidence a progressive partial filling/release of the trap energy levels, confirmed as well by pulsed measurements. Captured/released electrons modify the number of trap states available for tunneling and thus the current level. As a consequence, tunneling processes in the go and return paths take place through levels with different occupations within the TEB, originating the hysteresis cycle.
- Open Access
- 5 January 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (1)
Reverse-bias current hysteresis at low temperature in GaN Schottky barrier diodes
In this paper, we report an analysis of reverse current mechanisms observed in GaN Schottky barrier diodes leading to hysteretic behavior of the I–V curves at low temperature. By means of DC measurements from 33 to 475 K, we demonstrate the presence of two leakage mechanisms when comparing the experiments with the results obtained using a unified model to predict the ideal reverse current of the diode. Poole–Frenkel emission is the dominant mechanism for temperatures above 200 K, while trap-assisted tunneling prevails for lower temperatures, where also, hysteresis cycles are revealed by means of DC dual-sweep voltage measurements. The energy of the corresponding traps has also been determined, being around 0.2 and 0.45 eV, respectively. The hysteresis phenomenon is attributed to the bias-induced occupancy of the energy states originating the leakage-current processes, which leads to the reduction of the reverse current after a high negative voltage is applied to the diode.
- 5 January 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (1)
Open AccessReverse-bias current hysteresis at low temperature in GaN Schottky barrier diodes
In this paper, we report an analysis of reverse current mechanisms observed in GaN Schottky barrier diodes leading to hysteretic behavior of the I–V curves at low temperature. By means of DC measurements from 33 to 475 K, we demonstrate the presence of two leakage mechanisms when comparing the experiments with the results obtained using a unified model to predict the ideal reverse current of the diode. Poole–Frenkel emission is the dominant mechanism for temperatures above 200 K, while trap-assisted tunneling prevails for lower temperatures, where also, hysteresis cycles are revealed by means of DC dual-sweep voltage measurements. The energy of the corresponding traps has also been determined, being around 0.2 and 0.45 eV, respectively. The hysteresis phenomenon is attributed to the bias-induced occupancy of the energy states originating the leakage-current processes, which leads to the reduction of the reverse current after a high negative voltage is applied to the diode.
- 10 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (7) , 3447-3453
On the Practical Limitations for the Generation of Gunn Oscillations in Highly Doped GaN Diodes
Planar Gunn diodes based on doped GaN active layers with different geometries have been fabricated and characterized. Gunn oscillations have not been observed due to the catastrophic breakdown of the diodes for applied voltages around 20–25 V, much below the bias theoretically needed for the onset of Gunn oscillations. The breakdown of the diodes has been analyzed by pulsed ${I}$ – ${V}$ measurements at low temperatures, and it has been observed to be almost independent of the geometry of the channels, thus allowing to discard self-heating effects as the origin of the device burning. The other possible mechanism for the device failure is an impact-ionization avalanche due to the high electric fields present at the anode corner of the isolating trenches. However, Monte Carlo simulations using the typical value of the intervalley energy separation of GaN, $\varepsilon _{{1}-{2}}$ = 2.2 eV, show that impact ionization mechanisms are not significant for the voltages for which the experimental failure is observed. But recent experiments showed that $\varepsilon _{{1}-{2}}$ is lower, around 0.9 eV. This lower intervalley separation leads to a much lower threshold voltage for the Gunn oscillations, not far from the experimental breakdown. Therefore, we attribute the device’s failure to an avalanche process just when Gunn domains start to form, since they increase the population of electrons at the high electric field region, thus strongly enhancing impact ionization mechanisms that lead to the diode failure.
- 10 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (7) , 3447-3453
On the Practical Limitations for the Generation of Gunn Oscillations in Highly Doped GaN Diodes
Planar Gunn diodes based on doped GaN active layers with different geometries have been fabricated and characterized. Gunn oscillations have not been observed due to the catastrophic breakdown of the diodes for applied voltages around 20–25 V, much below the bias theoretically needed for the onset of Gunn oscillations. The breakdown of the diodes has been analyzed by pulsed ${I}$ – ${V}$ measurements at low temperatures, and it has been observed to be almost independent of the geometry of the channels, thus allowing to discard self-heating effects as the origin of the device burning. The other possible mechanism for the device failure is an impact-ionization avalanche due to the high electric fields present at the anode corner of the isolating trenches. However, Monte Carlo simulations using the typical value of the intervalley energy separation of GaN, $\varepsilon _{{1}-{2}}$ = 2.2 eV, show that impact ionization mechanisms are not significant for the voltages for which the experimental failure is observed. But recent experiments showed that $\varepsilon _{{1}-{2}}$ is lower, around 0.9 eV. This lower intervalley separation leads to a much lower threshold voltage for the Gunn oscillations, not far from the experimental breakdown. Therefore, we attribute the device’s failure to an avalanche process just when Gunn domains start to form, since they increase the population of electrons at the high electric field region, thus strongly enhancing impact ionization mechanisms that lead to the diode failure.
- 5 October 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (13) , 134501
Comparison of GaN and InGaAs high electron mobility transistors as zero-bias microwave detectors
We report on the measurements of the two main figures of merit for microwave detection, namely, responsivity and noise equivalent power (NEP), in HEMTs based on two of the most broadly used material systems AlGaN/GaN and AlInAs/InGaAs. A comparison between their performances as RF detectors in a wide temperature range is provided by means of experiments made under probes with direct connection to the drain contact. InGaAs HEMTs exhibit much better responsivity and NEP, which are further improved when lowering the working temperature. Moreover, we analyze the possibility of optimizing the current-mode detection of the transistors by improving the impedance matching conditions through an adequate choice of the device width .- 5 October 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (13) , 134501
Comparison of GaN and InGaAs high electron mobility transistors as zero-bias microwave detectors
We report on the measurements of the two main figures of merit for microwave detection, namely, responsivity and noise equivalent power (NEP), in HEMTs based on two of the most broadly used material systems AlGaN/GaN and AlInAs/InGaAs. A comparison between their performances as RF detectors in a wide temperature range is provided by means of experiments made under probes with direct connection to the drain contact. InGaAs HEMTs exhibit much better responsivity and NEP, which are further improved when lowering the working temperature. Moreover, we analyze the possibility of optimizing the current-mode detection of the transistors by improving the impedance matching conditions through an adequate choice of the device width .- 25 July 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (4) , 044502
Comprehensive model for ideal reverse leakage current components in Schottky barrier diodes tested in GaN-on-SiC samples
A model to predict the ideal reverse leakage currents in Schottky barrier diodes, namely, thermionic emission and tunneling components, has been developed and tested by means of current–voltage–temperature measurements in GaN-on-SiC devices. The model addresses both current components and both forward and reverse polarities in a unified way and with the same set of parameters. The values of the main parameters (barrier height, series resistance, and ideality factor) are extracted from the fitting of the forward-bias I–V curves and then used to predict the reverse-bias behavior without any further adjustment. An excellent agreement with the I–V curves measured in the forward bias in the GaN diode under analysis has been achieved in a wide range of temperatures (275–475 K). In reverse bias, at temperatures higher than 425 K, a quasi-ideal behavior is found, but additional mechanisms (most likely trap-assisted tunneling) lead to an excess of leakage current at lower temperatures. We demonstrate the importance of the inclusion of image-charge effects in the model in order to correctly predict the values of the reverse leakage current. Relevant physical information, like the energy range at which most of the tunnel injection takes place or the distance from the interface at which tunneled electrons emerge, is also provided by the model.
- 25 July 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (4) , 044502
Comprehensive model for ideal reverse leakage current components in Schottky barrier diodes tested in GaN-on-SiC samples
A model to predict the ideal reverse leakage currents in Schottky barrier diodes, namely, thermionic emission and tunneling components, has been developed and tested by means of current–voltage–temperature measurements in GaN-on-SiC devices. The model addresses both current components and both forward and reverse polarities in a unified way and with the same set of parameters. The values of the main parameters (barrier height, series resistance, and ideality factor) are extracted from the fitting of the forward-bias I–V curves and then used to predict the reverse-bias behavior without any further adjustment. An excellent agreement with the I–V curves measured in the forward bias in the GaN diode under analysis has been achieved in a wide range of temperatures (275–475 K). In reverse bias, at temperatures higher than 425 K, a quasi-ideal behavior is found, but additional mechanisms (most likely trap-assisted tunneling) lead to an excess of leakage current at lower temperatures. We demonstrate the importance of the inclusion of image-charge effects in the model in order to correctly predict the values of the reverse leakage current. Relevant physical information, like the energy range at which most of the tunnel injection takes place or the distance from the interface at which tunneled electrons emerge, is also provided by the model.
- Open Access
- 26 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (9) , 4296-4301
Dielectric Passivation and Edge Effects in Planar GaN Schottky Barrier Diodes
The influence of passivation on the edge effects (EEs) present in the capacitance-voltage ( C- V) characteristics of GaN Schottky barrier diodes (SBDs) with realistic geometry is analyzed by means of Monte Carlo simulations. The enhancement of the performance of SBDs as frequency multipliers is based on the optimization of the nonlinearity of the C- V curve, where EEs, strongly influenced by the dielectric passivation of the diode, play a significant role and must be carefully considered. The extra capacitance associated with EEs is affected by the presence of surface charges at the semiconductor/dielectric interface, which is considered by means of a self-consistent model in which the local value of the surface charge is updated according to the surrounding electron density. Our results indicate that, in realistic SBD geometries, a higher dielectric constant of the passivation material leads to more pronounced EEs. The thickness of the dielectric and the lateral extension of the epilayer are also important parameters to be taken into account when dealing with EEs.
- 26 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (9) , 4296-4301
Open AccessDielectric Passivation and Edge Effects in Planar GaN Schottky Barrier Diodes
The influence of passivation on the edge effects (EEs) present in the capacitance-voltage ( C- V) characteristics of GaN Schottky barrier diodes (SBDs) with realistic geometry is analyzed by means of Monte Carlo simulations. The enhancement of the performance of SBDs as frequency multipliers is based on the optimization of the nonlinearity of the C- V curve, where EEs, strongly influenced by the dielectric passivation of the diode, play a significant role and must be carefully considered. The extra capacitance associated with EEs is affected by the presence of surface charges at the semiconductor/dielectric interface, which is considered by means of a self-consistent model in which the local value of the surface charge is updated according to the surrounding electron density. Our results indicate that, in realistic SBD geometries, a higher dielectric constant of the passivation material leads to more pronounced EEs. The thickness of the dielectric and the lateral extension of the epilayer are also important parameters to be taken into account when dealing with EEs.
- Open Access
- 9 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 94-97
Technological Parameters and Edge Fringing Capacitance in GaN Schottky Barrier Diodes: Monte Carlo Simulations
Schottky barrier diodes (SBDs) with realistic geometries have been studied by means of a 2-D ensemble Monte Carlo simulator. The non-linearity of the Capacitance-Voltage (C-V) characteristic is the most important parameter for optimizing SBDs as frequency multipliers. In this paper, by changing the values of several technological parameters, we analyze their influence on the edge fringing capacitance in a GaN SBD. We have found that the parameters related with the dielectric used for the passivation and the lateral extension of the epilayer significantly affect the fringing capacitance, thus increasing the value of the total capacitance above the ideal one.
- 9 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 94-97
Open AccessTechnological Parameters and Edge Fringing Capacitance in GaN Schottky Barrier Diodes: Monte Carlo Simulations
Schottky barrier diodes (SBDs) with realistic geometries have been studied by means of a 2-D ensemble Monte Carlo simulator. The non-linearity of the Capacitance-Voltage (C-V) characteristic is the most important parameter for optimizing SBDs as frequency multipliers. In this paper, by changing the values of several technological parameters, we analyze their influence on the edge fringing capacitance in a GaN SBD. We have found that the parameters related with the dielectric used for the passivation and the lateral extension of the epilayer significantly affect the fringing capacitance, thus increasing the value of the total capacitance above the ideal one.
- 20 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (9) , 3530-3535
Analysis of Surface Charge Effects and Edge Fringing Capacitance in Planar GaAs and GaN Schottky Barrier Diodes
In this article, by means of a 2-D ensemble Monte Carlo simulator, the Schottky barrier diodes (SBDs) with realistic geometries based on GaAs and GaN are studied as promising devices for increasing the high-frequency performance- and power-handling capability of frequency mixers and multipliers. The nonlinearity of the capacitance-voltage (CV) characteristic is the most important parameter for optimizing the performance of SBDs as frequency multipliers. The small size of the diodes used for ultrahigh-frequency applications makes the value of its intrinsic capacitance to deviate from the ideal one due to fringing effects. We have observed that the value of the edge capacitance well into reverse bias does not depend on the applied voltage. We define an edge-effect parameter β, which, interestingly, is affected by the presence or absence of surface charges at the semiconductor-dielectric interface σ. Two physical models have been considered: a fixed σ related to a surface potential Vₛ constant surface-charge model (CCM) and a self-consistent model in which the local value of σ is dynamically evaluated depending on the surrounding electron density self-consistent surface-charge model (SCCM). Using the CCM, we obtain that β depends on the depth of the depletion region Wₛ created by the surface charges, nearly irrespectively of the epilayer doping or semiconductor type. The more realistic SCCM indicates that, at low frequencies, when the surface charges are able to follow the variations of the applied voltage, the value of β approaches the one obtained without surface charges, while the high-frequency value (the significant one) is smaller.
- 20 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (9) , 3530-3535
Analysis of Surface Charge Effects and Edge Fringing Capacitance in Planar GaAs and GaN Schottky Barrier Diodes
In this article, by means of a 2-D ensemble Monte Carlo simulator, the Schottky barrier diodes (SBDs) with realistic geometries based on GaAs and GaN are studied as promising devices for increasing the high-frequency performance- and power-handling capability of frequency mixers and multipliers. The nonlinearity of the capacitance-voltage (CV) characteristic is the most important parameter for optimizing the performance of SBDs as frequency multipliers. The small size of the diodes used for ultrahigh-frequency applications makes the value of its intrinsic capacitance to deviate from the ideal one due to fringing effects. We have observed that the value of the edge capacitance well into reverse bias does not depend on the applied voltage. We define an edge-effect parameter β, which, interestingly, is affected by the presence or absence of surface charges at the semiconductor-dielectric interface σ. Two physical models have been considered: a fixed σ related to a surface potential Vₛ constant surface-charge model (CCM) and a self-consistent model in which the local value of σ is dynamically evaluated depending on the surrounding electron density self-consistent surface-charge model (SCCM). Using the CCM, we obtain that β depends on the depth of the depletion region Wₛ created by the surface charges, nearly irrespectively of the epilayer doping or semiconductor type. The more realistic SCCM indicates that, at low frequencies, when the surface charges are able to follow the variations of the applied voltage, the value of β approaches the one obtained without surface charges, while the high-frequency value (the significant one) is smaller.