Alfred Franklin Varghese
Research Subjects
Alfred Franklin Varghese has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
T. Christopher
Government College of Engineering
4 shared publications- T. Christopher
Government College of Engineering
2 shared publications Beno Wincy Winsly
1 shared publication- Boggarapu Nageswara Rao
KL Deemed to be University Department of Mechanical Engineering, Koneru Lakshmaiah Education Foundation Green Fields, Guntur
1 shared publication - Gopinath Gunasekaran
University of Technology and Applied Sciences-Ibri
1 shared publication - Joseph Michel
University of Technology and Applied Sciences-Ibri
1 shared publication
Latest Publications
- Open Access
- 4 July 2021
- Published by IIUM Press in IIUM Engineering Journal
- Vol. 22 (2) , 352-363
ANALYTICAL AND NUMERICAL THERMAL ANALYSIS ON FRICTION STIR WELDING USING POLYGONAL TOOL PIN
Frictional heat generation in the tool/matrix interface followed by the stirring of material along the weld line causes plasticized solid state joining in friction stir welding. In this paper, the existing torque based thermo-mechanical model for the tools with cylindrical pins is remodified for the polygonal tool pin profile by introducing novel multiplication factors with respect to the number of sides in the tool pin geometry. The variation in the effective heat supply with respect to the chosen pin geometry was analyzed. A comparative analysis of the proposed analytical model with the existing model was also carried out to understand the accuracy of the proposed model. Furthermore, a transient thermal numerical modelling was carried out in the view of understanding the change in process peak temperature in the stir zone and change in temperature gradient along the heat affected zone with respect to the change in pin geometry for the opted set of process input parameters. An analytically estimated heat-input-based numerical model was adopted in the present study. It was observed that the process peak temperature was directly proportional to the number of sides in the tool pin. ABSTRAK: Penjanaan haba geseran antara muka pada alat/matrik diikuti dengan pengacauan material sepanjang garis kimpalan menyebabkan keadaan plastik pepejal melekat bersama geseran kimpalan pengacau. Kajian ini berkaitan tork sedia ada berdasarkan model mekanikal-terma bagi alat pin silinder yang terubah suai bagi profil pin alat poligon dengan memperkenalkan faktor gandaan berdasarkan bilangan sisi geometri alat pin. Perubahan pada bekalan haba efektif berdasarkan geometri pin pilihan telah dikaji. Analisis bandingan pada model analitik yang dicadang bersama model sedia ada, telah dilakukan bagi memahami ketepatan model cadangan. Tambahan, model transien numerikal terma telah dibuat bagi memahami proses perubahan suhu puncak ketika zon pengacauan dan perubahan gradien suhu sepanjang zon terkena haba perubahan geometri pin pada set proses parameter input terpilih. Kajian ini mengaplikasi model numerik berdasarkan input anggaran haba secara analitik. Dapatan kajian menunjukkan suhu puncak proses adalah berkadar langsung dengan bilangan sisi pin alat.
- 4 July 2021
- Published by IIUM Press in IIUM Engineering Journal
- Vol. 22 (2) , 352-363
Open AccessANALYTICAL AND NUMERICAL THERMAL ANALYSIS ON FRICTION STIR WELDING USING POLYGONAL TOOL PIN
Frictional heat generation in the tool/matrix interface followed by the stirring of material along the weld line causes plasticized solid state joining in friction stir welding. In this paper, the existing torque based thermo-mechanical model for the tools with cylindrical pins is remodified for the polygonal tool pin profile by introducing novel multiplication factors with respect to the number of sides in the tool pin geometry. The variation in the effective heat supply with respect to the chosen pin geometry was analyzed. A comparative analysis of the proposed analytical model with the existing model was also carried out to understand the accuracy of the proposed model. Furthermore, a transient thermal numerical modelling was carried out in the view of understanding the change in process peak temperature in the stir zone and change in temperature gradient along the heat affected zone with respect to the change in pin geometry for the opted set of process input parameters. An analytically estimated heat-input-based numerical model was adopted in the present study. It was observed that the process peak temperature was directly proportional to the number of sides in the tool pin. ABSTRAK: Penjanaan haba geseran antara muka pada alat/matrik diikuti dengan pengacauan material sepanjang garis kimpalan menyebabkan keadaan plastik pepejal melekat bersama geseran kimpalan pengacau. Kajian ini berkaitan tork sedia ada berdasarkan model mekanikal-terma bagi alat pin silinder yang terubah suai bagi profil pin alat poligon dengan memperkenalkan faktor gandaan berdasarkan bilangan sisi geometri alat pin. Perubahan pada bekalan haba efektif berdasarkan geometri pin pilihan telah dikaji. Analisis bandingan pada model analitik yang dicadang bersama model sedia ada, telah dilakukan bagi memahami ketepatan model cadangan. Tambahan, model transien numerikal terma telah dibuat bagi memahami proses perubahan suhu puncak ketika zon pengacauan dan perubahan gradien suhu sepanjang zon terkena haba perubahan geometri pin pada set proses parameter input terpilih. Kajian ini mengaplikasi model numerik berdasarkan input anggaran haba secara analitik. Dapatan kajian menunjukkan suhu puncak proses adalah berkadar langsung dengan bilangan sisi pin alat.
- 28 November 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 125616
Generation of mixed mode I/II failure criteria from MMB specimens: an experimental study
Characterization of resistance to delamination is of great importance in selection of composite material. Mixed mode delamination is one of the most serious failure modes in aerospace composites. This article examines the delamination behaviour of mixed mode bending (MMB) test specimens made of glass/epoxy and carbon/epoxy composites. Literature published test data on different composites have been utilzed to identify the best suited failure criterion. Benzeggagh-Kenane (B-K) criterion as well as the polynomial criteria are used to generate failure envelopes from the fracture toughness data of composite specimens. Experiments were conducted on unidirectional fiber reinforced epoxy MMB specimens to analyze the failure trend of laminated composites and to validate the proposed polynomial criteria. Present investigations reveal that both B-K and polynomial criteria fit well for unidirectional specimens and cubic polynomial criterion fits well for angle-ply specimens.
- 28 November 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 125616
Generation of mixed mode I/II failure criteria from MMB specimens: an experimental study
Characterization of resistance to delamination is of great importance in selection of composite material. Mixed mode delamination is one of the most serious failure modes in aerospace composites. This article examines the delamination behaviour of mixed mode bending (MMB) test specimens made of glass/epoxy and carbon/epoxy composites. Literature published test data on different composites have been utilzed to identify the best suited failure criterion. Benzeggagh-Kenane (B-K) criterion as well as the polynomial criteria are used to generate failure envelopes from the fracture toughness data of composite specimens. Experiments were conducted on unidirectional fiber reinforced epoxy MMB specimens to analyze the failure trend of laminated composites and to validate the proposed polynomial criteria. Present investigations reveal that both B-K and polynomial criteria fit well for unidirectional specimens and cubic polynomial criterion fits well for angle-ply specimens.
- 1 November 2015
- Published by Springer Nature in Strength of Materials
- Vol. 47 (6) , 789-796
Interlaminar Fracture Toughness Estimation of Aerospace Composites by Weighted Residual Approach
- 1 November 2015
- Published by Springer Nature in Strength of Materials
- Vol. 47 (6) , 789-796
Interlaminar Fracture Toughness Estimation of Aerospace Composites by Weighted Residual Approach
- 28 August 2015
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 787, 335-339
Generation of Crack Growth Resistance Curve from ENF Specimens Made of Glass/Epoxy: An Experimental Study
This article examines the fracture toughness of end notched flexure (ENF) composite specimens of three different lay-ups. Experiments were conducted on these glass/epoxy specimens and the critical fracture energy,, was evaluated based on compliance based beam method (CBBM). Classical methods require crack length measurements, which are not easy to obtain as propagation occurs rapidly without a clear opening. The CBBM is based on crack equivalent concept, which does not require crack length monitoring during propagation and hence the crack growth resistance curve (R-curve) can be generated in a much easier way. Moreover, the CBBM accounts the non-negligible energy dissipation in the fracture process zone (FPZ) in addition to stress concentrations near crack tip, contact between specimen arms at the pre-crack region and root rotation effects. Hence, the complete R-curves of ENF specimens of different lay-ups were obtained using the CBBM with higher degree of accuracy. It was observed that the unidirectional specimen did show higher propagation toughness value than the angle-ply and cross-ply specimens.
- 28 August 2015
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 787, 335-339
Generation of Crack Growth Resistance Curve from ENF Specimens Made of Glass/Epoxy: An Experimental Study
This article examines the fracture toughness of end notched flexure (ENF) composite specimens of three different lay-ups. Experiments were conducted on these glass/epoxy specimens and the critical fracture energy,, was evaluated based on compliance based beam method (CBBM). Classical methods require crack length measurements, which are not easy to obtain as propagation occurs rapidly without a clear opening. The CBBM is based on crack equivalent concept, which does not require crack length monitoring during propagation and hence the crack growth resistance curve (R-curve) can be generated in a much easier way. Moreover, the CBBM accounts the non-negligible energy dissipation in the fracture process zone (FPZ) in addition to stress concentrations near crack tip, contact between specimen arms at the pre-crack region and root rotation effects. Hence, the complete R-curves of ENF specimens of different lay-ups were obtained using the CBBM with higher degree of accuracy. It was observed that the unidirectional specimen did show higher propagation toughness value than the angle-ply and cross-ply specimens.
- Open Access
- 12 November 2014
- Published by Hindawi Limited in Journal of Composites
- Vol. 2014, 1-10
Generation of R-Curve from 4ENF Specimens: An Experimental Study
The experimental determination of the resistance to delamination is very important in aerospace applications as composite materials have superior properties only in the fiber direction. To measure the interlaminar fracture toughness of composite materials, different kinds of specimens and experimental methods are available. This article examines the fracture energy of four-point end-notched flexure (4ENF) composite specimens made of carbon/epoxy and glass/epoxy. Experiments were conducted on these laminates and the mode II fracture energy, , was evaluated using compliance method and was compared with beam theory solution. The crack growth resistance curve (R-curve) for these specimens was generated and the found glass/epoxy shows higher toughness values than carbon/epoxy composite. From this study, it was observed that R-curve effect in 4ENF specimens is quite mild, which means that the measured delamination toughness, , is more accurate.- 12 November 2014
- Published by Hindawi Limited in Journal of Composites
- Vol. 2014, 1-10
Open AccessGeneration of R-Curve from 4ENF Specimens: An Experimental Study
The experimental determination of the resistance to delamination is very important in aerospace applications as composite materials have superior properties only in the fiber direction. To measure the interlaminar fracture toughness of composite materials, different kinds of specimens and experimental methods are available. This article examines the fracture energy of four-point end-notched flexure (4ENF) composite specimens made of carbon/epoxy and glass/epoxy. Experiments were conducted on these laminates and the mode II fracture energy, , was evaluated using compliance method and was compared with beam theory solution. The crack growth resistance curve (R-curve) for these specimens was generated and the found glass/epoxy shows higher toughness values than carbon/epoxy composite. From this study, it was observed that R-curve effect in 4ENF specimens is quite mild, which means that the measured delamination toughness, , is more accurate. - Open Access
- 20 October 2014
- Published by Wiley in International Journal of Aerospace Engineering
- Vol. 2014, 1-12
Influence of Root Rotation on Delamination Fracture Toughness of Composites
Large deviations have been observed while analysing composite double cantilever beam (DCB) specimens assuming each cracked half as a simple cantilever beam. This paper examines the effect of rotational spring stiffnesson the critical fracture energyconsidering nonzero slope at the crack-tip of the DCB specimen by modelling each cracked half as the spring-hinged cantilever beam. The critical load estimates of DCB specimens fromare found to be in good agreement with in-house and existing test results of different composite material systems.- 20 October 2014
- Published by Wiley in International Journal of Aerospace Engineering
- Vol. 2014, 1-12
Open AccessInfluence of Root Rotation on Delamination Fracture Toughness of Composites
Large deviations have been observed while analysing composite double cantilever beam (DCB) specimens assuming each cracked half as a simple cantilever beam. This paper examines the effect of rotational spring stiffnesson the critical fracture energyconsidering nonzero slope at the crack-tip of the DCB specimen by modelling each cracked half as the spring-hinged cantilever beam. The critical load estimates of DCB specimens fromare found to be in good agreement with in-house and existing test results of different composite material systems. - 1 November 2013
- Published by Springer Nature in Strength of Materials
- Vol. 45 (6) , 674-683
Generation and Validation of Crack Growth Resistance Curve from DCB Specimens: An Experimental Study
- 1 November 2013
- Published by Springer Nature in Strength of Materials
- Vol. 45 (6) , 674-683
Generation and Validation of Crack Growth Resistance Curve from DCB Specimens: An Experimental Study
- Open Access
- 14 July 2013
- Published by Hindawi Limited in Advances in Materials Science and Engineering
- Vol. 2013, 1-7
Fracture Energy Estimation of DCB Specimens Made of Glass/Epoxy: An Experimental Study
This paper examines critical load and corresponding displacement of double cantilever beam (DCB) composite specimens made of glass/epoxy of three different layups. Experiments were conducted on these laminates, and the fracture energy,, was evaluated considering the root rotation at the crack tip. The present model requires the applied load-displacement history and crack extension to estimate fracture energy. Reduction schemes based on cubic and power law are also proposed to determine Young’s modulus and energy release rate and found good agreement with the published and test results.- 14 July 2013
- Published by Hindawi Limited in Advances in Materials Science and Engineering
- Vol. 2013, 1-7
Open AccessFracture Energy Estimation of DCB Specimens Made of Glass/Epoxy: An Experimental Study
This paper examines critical load and corresponding displacement of double cantilever beam (DCB) composite specimens made of glass/epoxy of three different layups. Experiments were conducted on these laminates, and the fracture energy,, was evaluated considering the root rotation at the crack tip. The present model requires the applied load-displacement history and crack extension to estimate fracture energy. Reduction schemes based on cubic and power law are also proposed to determine Young’s modulus and energy release rate and found good agreement with the published and test results.