Catrin Mair Davies
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Catrin Mair Davies has a total of 259 co-authors. Here are the top co-authors by number of shared publications:
K. M. Nikbin
Imperial College London, London, UK
26 shared publications- Ali Mehmanparast
Department of Naval Architecture, Ocean and Marine Engineering, University of Strathclyde, Glasgow G1 1XQ, UK
25 shared publications Kamran M. Nikbin
Imperial College London, London, UK
18 shared publications- Paul A. Hooper
Department of Mechanical Engineering, Imperial College London, London, UK
17 shared publications K.M. Nikbin
Imperial College London
14 shared publications- Jianguo Lin
Department of Mechanical Engineering, Imperial College London, London SW7 2AZ, UK
12 shared publications
Latest Publications
- Open Access
- 27 July 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (9) , 9565-9579
Residual stress prediction for laser powder bed fusion parts: a critical assessment of inherent strain and block dump modelling strategies
Metal additive manufacturing, particularly laser powder bed fusion (LPBF), offers major advantages in design flexibility and near-net-shape production. However, the steep thermal gradients inherent to the process generate high residual stresses that can lead to distortion or cracking, thereby compromising part integrity. Conventional optimisation of process parameters through trial-and-error experimentation is costly and time-consuming, underscoring the need for reliable modelling strategies. In this study, two part-scale simulation approaches, the inherent strain method and the block dump method, were systematically evaluated for residual stress prediction in LPBF of Hastelloy X. Representative finite element implementations were developed and benchmarked against experimental observations, including cantilever deflections and residual stress fields obtained from neutron diffraction. Both methods captured the experimental trends with good overall consistency. The block dump method achieved slightly higher accuracy without requiring calibration, but at the expense of increased computational cost and reliance on a more comprehensive set of material input data, including temperature-dependent thermal and mechanical material properties. Sensitivity analyses further showed that predictions from the inherent strain method are highly dependent on the calibration of the inherent strain tensor, whereas the block dump method is more robust with respect to modelling assumptions. Finally, the results of this study indicate that while both strategies offer practical predictive capability, the block dump method provides better generalisation capability for residual stress prediction in LPBF components.
- 27 July 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (9) , 9565-9579
Open AccessResidual stress prediction for laser powder bed fusion parts: a critical assessment of inherent strain and block dump modelling strategies
Metal additive manufacturing, particularly laser powder bed fusion (LPBF), offers major advantages in design flexibility and near-net-shape production. However, the steep thermal gradients inherent to the process generate high residual stresses that can lead to distortion or cracking, thereby compromising part integrity. Conventional optimisation of process parameters through trial-and-error experimentation is costly and time-consuming, underscoring the need for reliable modelling strategies. In this study, two part-scale simulation approaches, the inherent strain method and the block dump method, were systematically evaluated for residual stress prediction in LPBF of Hastelloy X. Representative finite element implementations were developed and benchmarked against experimental observations, including cantilever deflections and residual stress fields obtained from neutron diffraction. Both methods captured the experimental trends with good overall consistency. The block dump method achieved slightly higher accuracy without requiring calibration, but at the expense of increased computational cost and reliance on a more comprehensive set of material input data, including temperature-dependent thermal and mechanical material properties. Sensitivity analyses further showed that predictions from the inherent strain method are highly dependent on the calibration of the inherent strain tensor, whereas the block dump method is more robust with respect to modelling assumptions. Finally, the results of this study indicate that while both strategies offer practical predictive capability, the block dump method provides better generalisation capability for residual stress prediction in LPBF components.
- 5 December 2025
- Published by Elsevier in NDT & E International
- Vol. 159
A skipping Rayleigh wave technique for discontinuous creep crack sizing at high temperature
- 5 December 2025
- Published by Elsevier in NDT & E International
- Vol. 159
A skipping Rayleigh wave technique for discontinuous creep crack sizing at high temperature
- Open Access
- 22 September 2022
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 16 (62) , 261-270
Numerical simulation of creep notched bar of P91 steel
Numerous components designed for use at elevated temperatures now exhibit multiaxial stress states as a result of geometric modification and material inhomogeneity. It is necessary to anticipate the creep rupture life of such components when subjected to multiaxial load. In this work finite element analysis has been performed to study the influence of different notches, namely blunt and medium notches on the stress distribution across the notch throat during the creep exposure. Within the FE model, a ductility exhaustion model based on the Cocks and Ashby model was utilized to forecast the creep rupture time of notched bar P91 material. The lower and upper bound of creep ductility are employed in the FE analysis. Different notch specimens have different stress and damage distribution. It is shown that for both types of notches, the von Mises stress is lower than the net stress, indicating the notch strengthening effect. The accumulation of creep damage in the minimum cross-section at each element across the notch throat increases over time. The point at which damage first occurs is closer to the notch root for the medium notch than for the blunt notch. The long-term rupture life predicted for blunt notch specimens appears to be comparable to that of uniaxial specimens. The upper bound creep ductility better predicts the rupture life for medium notches.
- 22 September 2022
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 16 (62) , 261-270
Open AccessNumerical simulation of creep notched bar of P91 steel
Numerous components designed for use at elevated temperatures now exhibit multiaxial stress states as a result of geometric modification and material inhomogeneity. It is necessary to anticipate the creep rupture life of such components when subjected to multiaxial load. In this work finite element analysis has been performed to study the influence of different notches, namely blunt and medium notches on the stress distribution across the notch throat during the creep exposure. Within the FE model, a ductility exhaustion model based on the Cocks and Ashby model was utilized to forecast the creep rupture time of notched bar P91 material. The lower and upper bound of creep ductility are employed in the FE analysis. Different notch specimens have different stress and damage distribution. It is shown that for both types of notches, the von Mises stress is lower than the net stress, indicating the notch strengthening effect. The accumulation of creep damage in the minimum cross-section at each element across the notch throat increases over time. The point at which damage first occurs is closer to the notch root for the medium notch than for the blunt notch. The long-term rupture life predicted for blunt notch specimens appears to be comparable to that of uniaxial specimens. The upper bound creep ductility better predicts the rupture life for medium notches.
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
X-Ray Diffraction Measurements and Computational Prediction of Residual Stress Mitigation Scanning Strategies in Powder Bed Fusion Additive Manufacturing
The repeated localised heating-melting-cooling-solidification processes during laser beam powder bed fusion (PBF-LB) additive manufacturing (AM) induce intricate thermal residual stress (RS) in manufactured parts. Non-destructive in-situ characterisation using X-ray diffraction was used to measure the RS of Ti-6Al-4V square plates that were manufactured by using six different scanning strategies. Computational modelling was used to interpret the experimental stress measurement results. It was revealed that an inclined scanning strategy is beneficial for reducing the average through-thickness RS because the inclined scanning strategy can mitigate the non-uniform thermal profile and corresponding residual thermal stresses in successive layers of material. Among all the different scanning strategies that were analysed in this work, the 45° inclined scanning strategy resulted in the lowest RS. The thick parts have a greater gradient of RS than the thinner parts, after base plate removal. This research outcome can help the AM industry to design or optimise the process parameters of the PBF-LB aiming to minimise the RS of metal parts.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessX-Ray Diffraction Measurements and Computational Prediction of Residual Stress Mitigation Scanning Strategies in Powder Bed Fusion Additive Manufacturing
The repeated localised heating-melting-cooling-solidification processes during laser beam powder bed fusion (PBF-LB) additive manufacturing (AM) induce intricate thermal residual stress (RS) in manufactured parts. Non-destructive in-situ characterisation using X-ray diffraction was used to measure the RS of Ti-6Al-4V square plates that were manufactured by using six different scanning strategies. Computational modelling was used to interpret the experimental stress measurement results. It was revealed that an inclined scanning strategy is beneficial for reducing the average through-thickness RS because the inclined scanning strategy can mitigate the non-uniform thermal profile and corresponding residual thermal stresses in successive layers of material. Among all the different scanning strategies that were analysed in this work, the 45° inclined scanning strategy resulted in the lowest RS. The thick parts have a greater gradient of RS than the thinner parts, after base plate removal. This research outcome can help the AM industry to design or optimise the process parameters of the PBF-LB aiming to minimise the RS of metal parts.
- Open Access
- 16 July 2021
- Published by ASME International
Application of a Novel Load Line Displacement Partitioning Technique to Creep Crack Growth Tests on Sen(t) Geometries of Type 316h Stainless Steel
In CCG (creep crack growth) tests, the LLD (load line displacement) and LLD rates are measured and used to calculate the creep fracture mechanics paparameter C\*. To date the plastic contribution to the LLD has been evaluated by assuming a power-law relationship for plastic deformation or C\* has been calculated by totally neglecting the contribution of plasticity to the LLD
- 16 July 2021
- Published by ASME International
Open AccessApplication of a Novel Load Line Displacement Partitioning Technique to Creep Crack Growth Tests on Sen(t) Geometries of Type 316h Stainless Steel
In CCG (creep crack growth) tests, the LLD (load line displacement) and LLD rates are measured and used to calculate the creep fracture mechanics paparameter C\*. To date the plastic contribution to the LLD has been evaluated by assuming a power-law relationship for plastic deformation or C\* has been calculated by totally neglecting the contribution of plasticity to the LLD
- Open Access
- 16 July 2021
- Published by ASME International
Residual Stress Measurements in a 316l Uniaxial Fatigue Sample Manufactured by Laser Powder Bed Fusion
Laser powder bed fusion(LPBF) is a novel metal-based additive manufacturing (AM) process which offers numerous advantages over conventional material processing routes. There has been significant interest in using LPBF to manufacture bespoke components. Since LPBF) is a complex thermo-mechanical process, substantial residual stresses (RS) are generated during their manufacture
- 16 July 2021
- Published by ASME International
Open AccessResidual Stress Measurements in a 316l Uniaxial Fatigue Sample Manufactured by Laser Powder Bed Fusion
Laser powder bed fusion(LPBF) is a novel metal-based additive manufacturing (AM) process which offers numerous advantages over conventional material processing routes. There has been significant interest in using LPBF to manufacture bespoke components. Since LPBF) is a complex thermo-mechanical process, substantial residual stresses (RS) are generated during their manufacture
- 3 August 2020
- Published by ASME International
Residual Stress Measurements in a 316L Uniaxial Samples Manufactured by Laser Powder Bed Fusion
Uniaxial samples have been manufactured for tension/compression testing from 316L stainless steel by laser powder bed fusion (LPBF). Samples manufactured by LPBF are known to contain high levels of residual stresses. These uniaxial samples were built from a solid cylindrical rod and subsequently machined to reduce the central cross section of the sample to the required gauge diameter and improve the surface finish. Finite element (FE) models have been developed to simulate the LPBF process of the rods, their removal from the build plate and subsequent machining into the tension/compression samples. High tensile residual stresses were predicted at the surface of the samples, balances by similar magnitude compressive stresses along their axis. Post machining however, these stresses were reduced by around 80% or more. Residual stress measurements were performed on the samples post machining using the neutron diffraction techniques. These measurements confirmed that negligible residual stresses remained in the samples post removal from the build plate and machining.
- 3 August 2020
- Published by ASME International
Residual Stress Measurements in a 316L Uniaxial Samples Manufactured by Laser Powder Bed Fusion
Uniaxial samples have been manufactured for tension/compression testing from 316L stainless steel by laser powder bed fusion (LPBF). Samples manufactured by LPBF are known to contain high levels of residual stresses. These uniaxial samples were built from a solid cylindrical rod and subsequently machined to reduce the central cross section of the sample to the required gauge diameter and improve the surface finish. Finite element (FE) models have been developed to simulate the LPBF process of the rods, their removal from the build plate and subsequent machining into the tension/compression samples. High tensile residual stresses were predicted at the surface of the samples, balances by similar magnitude compressive stresses along their axis. Post machining however, these stresses were reduced by around 80% or more. Residual stress measurements were performed on the samples post machining using the neutron diffraction techniques. These measurements confirmed that negligible residual stresses remained in the samples post removal from the build plate and machining.
- 1 July 2020
- Published by Elsevier in Ocean Engineering
- Vol. 208
Structural integrity assessment of floating offshore wind turbine support structures
- 1 July 2020
- Published by Elsevier in Ocean Engineering
- Vol. 208
Structural integrity assessment of floating offshore wind turbine support structures
- Top Cited PapersOpen Access
- 1 April 2020
- Published by Elsevier in Materials & Design
- Vol. 189
Revealing relationships between porosity, microstructure and mechanical properties of laser powder bed fusion 316L stainless steel through heat treatment
- 1 April 2020
- Published by Elsevier in Materials & Design
- Vol. 189
Top Cited PapersOpen AccessRevealing relationships between porosity, microstructure and mechanical properties of laser powder bed fusion 316L stainless steel through heat treatment