Henri Pepin
Research Subjects
Henri Pepin has a total of 75 co-authors. Here are the top co-authors by number of shared publications:
- Mohamed Chaker
Institut National de la Recherche Scientifique
3 shared publications - Julien Fuchs
LULI -CNRS CEA UPMC Univ Paris
2 shared publications - Marco Borghesi
Queen's University Belfast
2 shared publications - Yasuhiko Sentoku
The University of Osaka
2 shared publications A Ginovker
Institut National de la Recherche Scientifique
1 shared publicationA Jean
Institut National de la Recherche Scientifique
1 shared publication
Latest Publications
- Open Access
- 3 November 2017
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 3 (11) , e1700982-1700982
Laboratory unraveling of matter accretion in young stars
When matter accretes onto a young star, a shell of dense material can form around the impact, reducing its x-ray emission.
- 3 November 2017
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 3 (11) , e1700982-1700982
Open AccessLaboratory unraveling of matter accretion in young stars
When matter accretes onto a young star, a shell of dense material can form around the impact, reducing its x-ray emission.
- 1 April 2015
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 86 (4) , 043502
A compact broadband ion beam focusing device based on laser-driven megagauss thermoelectric magnetic fields
Ultra-intense lasers can nowadays routinely accelerate kiloampere ion beams. These unique sources of particle beams could impact many societal (e.g., proton-therapy or fuel recycling) and fundamental (e.g., neutron probing) domains. However, this requires overcoming the beam angular divergence at the source. This has been attempted, either with large-scale conventional setups or with compact plasma techniques that however have the restriction of short (50 ps), thermoelectric multi-megagauss surface magnetic (B)-fields, compact capturing, and focusing of a diverging laser-driven multi-MeV ion beam can be achieved over a wide range of ion energies in the limit of a 5° acceptance angle.
- 1 April 2015
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 86 (4) , 043502
A compact broadband ion beam focusing device based on laser-driven megagauss thermoelectric magnetic fields
Ultra-intense lasers can nowadays routinely accelerate kiloampere ion beams. These unique sources of particle beams could impact many societal (e.g., proton-therapy or fuel recycling) and fundamental (e.g., neutron probing) domains. However, this requires overcoming the beam angular divergence at the source. This has been attempted, either with large-scale conventional setups or with compact plasma techniques that however have the restriction of short (50 ps), thermoelectric multi-megagauss surface magnetic (B)-fields, compact capturing, and focusing of a diverging laser-driven multi-MeV ion beam can be achieved over a wide range of ion energies in the limit of a 5° acceptance angle.
- 1 August 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 36 (4) , 1817-1820
Generation of MeV-Range Protons From 30–100 nm Solid Targets by Ultra-High-Contrast Laser Pulses
- 1 August 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 36 (4) , 1817-1820
Generation of MeV-Range Protons From 30–100 nm Solid Targets by Ultra-High-Contrast Laser Pulses
- 1 August 1993
- Published by Optica Publishing Group in Applied Optics
- Vol. 32 (22) , 4247-4252
Time-resolved kiloelectron-volt spectroscopy of ultrashort plasmas
Optics InfoBase is the Optical Society's online library for flagship journals, partnered and copublished journals, and recent proceedings from OSA conferences.
- 1 August 1993
- Published by Optica Publishing Group in Applied Optics
- Vol. 32 (22) , 4247-4252
Time-resolved kiloelectron-volt spectroscopy of ultrashort plasmas
Optics InfoBase is the Optical Society's online library for flagship journals, partnered and copublished journals, and recent proceedings from OSA conferences.
- 1 November 1992
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
- Vol. 10 (6) , 3239-3242
Laser plasma sources for proximity printing or projection x-ray lithography
In this article, we present a theoretical and experimental study of the x-ray emission produced by laser plasma sources in different spectral ranges appropriate for x-ray lithography either in proximity printing (XRL) or projection (XRPL) approaches. For XRPL application, experiments using 10 ns laser pulses show that the maximum conversion efficiency in the (80–250 eV) range is attained at I=1011 W cm−2 whereas for 25 ns pulses and I≤6×1011 W cm−2, it is still increasing with laser intensity. On the other hand, higher laser intensities are required to obtain a high conversion efficiency for XRL (0.9–1.4 keV). Efficient emission peaked at 1.1 keV can be achieved for I≥1013 W cm−2 with copper targets and pulse duration shorter than 5 ns. For iron line emission (peak at 0.9 keV), the laser intensity can be lower (I=5×1012 W cm−2) and the pulse duration longer (τp=10 ns). Finally, we discuss the different approaches which may lead to the appropriate laser design.
- 1 November 1992
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
- Vol. 10 (6) , 3239-3242
Laser plasma sources for proximity printing or projection x-ray lithography
In this article, we present a theoretical and experimental study of the x-ray emission produced by laser plasma sources in different spectral ranges appropriate for x-ray lithography either in proximity printing (XRL) or projection (XRPL) approaches. For XRPL application, experiments using 10 ns laser pulses show that the maximum conversion efficiency in the (80–250 eV) range is attained at I=1011 W cm−2 whereas for 25 ns pulses and I≤6×1011 W cm−2, it is still increasing with laser intensity. On the other hand, higher laser intensities are required to obtain a high conversion efficiency for XRL (0.9–1.4 keV). Efficient emission peaked at 1.1 keV can be achieved for I≥1013 W cm−2 with copper targets and pulse duration shorter than 5 ns. For iron line emission (peak at 0.9 keV), the laser intensity can be lower (I=5×1012 W cm−2) and the pulse duration longer (τp=10 ns). Finally, we discuss the different approaches which may lead to the appropriate laser design.
- 1 August 1991
- Published by SPIE-Intl Soc Optical Eng
- Vol. 1465, 16-26
Recent developments of x-ray lithography in Canada
An overview of current activities in Canada is reported, including x-ray lithography studies based on laser plasma sources and x-ray mask development. In particular, the application of laser plasma sources for x-ray lithography is discussed, taking into account the industrial requirement and the present state of laser technology. The authors describe the development of silicon carbide membranes for x-ray lithography application. SiC films were prepared using either a 100 kHz plasma-enhanced chemical vapor deposition (PECVD) system or a laser ablation technique. These membranes have a relatively large diameter (> 1 in.) and a high optical transparency (> 50%). Experimental studies on stresses in tungsten films deposited with triode sputtering are reported.
- 1 August 1991
- Published by SPIE-Intl Soc Optical Eng
- Vol. 1465, 16-26
Recent developments of x-ray lithography in Canada
An overview of current activities in Canada is reported, including x-ray lithography studies based on laser plasma sources and x-ray mask development. In particular, the application of laser plasma sources for x-ray lithography is discussed, taking into account the industrial requirement and the present state of laser technology. The authors describe the development of silicon carbide membranes for x-ray lithography application. SiC films were prepared using either a 100 kHz plasma-enhanced chemical vapor deposition (PECVD) system or a laser ablation technique. These membranes have a relatively large diameter (> 1 in.) and a high optical transparency (> 50%). Experimental studies on stresses in tungsten films deposited with triode sputtering are reported.