ILIgnacio Lope

Ignacio Lope

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ignacio Lope has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Comparative Evaluation of Different Cables for Magnetic Couplers in Inductive Power Transfer Systems

    by Jesús Acero, Ignacio Lope, Claudio Carretero, Héctor Sarnago, José Miguel Burdío

    Copper litz wires are widely used in wireless charging stations of light-duty electric vehicles. This type of cable is specifically mentioned in the SAE J2954 standard. However, details as the number and diameter of strands, or the material of conductors are not mentioned in the standard, which makes room to address some research and innovations. In this work, several alternatives to the traditional copper-litz wires are analyzed. Specifically, aluminum litz wire, copper-clad aluminum litz wire, and copper tubes are considered as alternatives to standard litz wire for the mentioned application. Potential benefits of the considered alternatives could include weight and cost savings. However, these advantages could not be enough to justify a wiring change if the resistance of the power pads increases and, equivalently, the efficiency of the electromagnetic power transfer decreases. For this reason, a model of the parasitic resistance of windings is proposed by combining the analytical ac resistance of two-layered round strands and finite element simulations. This model is used to obtain a figure of merit related with the efficiency of the electromagnetic energy transfer which is used to compare the different cables. Apart from efficiency, thermal behavior, cost and weight are also considered for comparison purposes. As a result, some conclusions about the suitability of each cable with respect to the operating frequency range are extracted.


  • Printed Circuit Board Coils of Multitrack Litz Structure for 3.3-kW Inductive Power Transfer System

    by Alexis Narvaez, Claudio Carretero, Ignacio Lope, Jesus Acero

    This paper presents the optimization procedure of an inductive power transmission (IPT) system which utilizes large size spiral printed circuit board (PCB) coils for high-power transfer. Printed circuit boards for coil assembly provides advantages in the manufacturing process through the use of cost-effective flexible fabrication techniques. Furthermore, this kind of construction offers a low profile device, which is of great interest for applications with space constraints. PCB-based IPT system coils can achieve high energy efficiency by applying litz-structure braiding techniques, as investigated in this work, where the objective was to obtain an optimized balance between the conduction losses and proximity losses associated with the number and dimensions of the traces. Considering the geometrical dimensions and manufacturing constraints, we will proceed to obtain the characteristics of the coil to achieve optimal performance. The estimation of coil losses were in part based on finite element simulations, and the results were conveniently processed with the appropriate mathematical methods. Numerical simulation and experimental results were conducted for validation on a prototype suitable to transfer up to 3.3 kW for a transmitter-receiver distance of 10 cm. In the experimental arrangement, a maximum efficiency in the coils of 93% has been measured, and the overall efficiency of 88% has been reached for the entire IPT system.


  • Open Access

    Modeling and Design of Cookware for Induction Heating Technology With Balanced Electromagnetic and Thermal Characteristics

    by Emilio Plumed, Ignacio Lope, Jesus Acero

    Improving the cooking experience of induction-heating users involves, among other factors, an optimized power distribution at the bottom of the cooking vessel. Conventional ferromagnetic cookware presents high efficiency but unequal temperature distribution with flat inductors, which subsequently leads to uneven cooking results. In this work, we propose an alternative to the traditional cookware arrangement by inserting some aluminum pieces in the ferromagnetic bottom of cookware. This arrangement combines the optimal inductive performance of the ferromagnetic iron an the high thermal conductivity of aluminum. The performance of the proposed arrangement is analyzed by means of a multiphysics tool including electromagnetic and heat transfer sub-models which is applied to predict both the equivalent electrical circuit and the temperature distribution in cookware. As a result, a balanced trade-off between efficiency and temperature distribution is evidenced with the proposed solution. Experimental results also corroborates the predictions of the proposed solution.


  • Domestic Induction Heating System With Standard Primary Inductor for Reduced-Size and High Distance Cookware

    by Emilio Plumed, Ignacio Lope, Jesus Acero, Jose Miguel Burdio

    In this work, a hybrid wireless power transfer system which combines induction heating (IH) and inductive power transfer (IPT) functionalities is proposed to improve the performance of a domestic induction heating application with small loads weakly coupled to distant inductors. Considering the basic single-inductor domestic IH application, the addition of a secondary inductor with series compensation capacitor directly attached to the small ferromagnetic cookware. This inductor allows to adapt the primary inductor to the load size, extending load distance while avoiding increased power losses and stress in electronic components. The extended distance can be used to implement the glassless induction concept, where the ceramic glass of typical cooktops is substituted by the kitchen surface itself. The design of the secondary coil is carried out by means of a combination of Finite Element simulations and electrical simulations. A design process including the housing of the resonant capacitors and the selection of the secondary winding number of turns and cabling is presented. As a result, a prototype is implemented and tested under working conditions up to 1500 W at several distances. Experimental results validate the electrical modelling and simulation. Moreover, thermal results confirm the feasibility of the proposal and validate the adopted strategies for the capacitor housing.


  • Induction Heating of Two Magnetically Independent Loads With a Single Transmitter

    by Emilio Plumed, Ignacio Lope, Jesus Acero, Jose Miguel Burdio

    This article introduces the design of a system capable of heating two magnetically independent ferromagnetic loads placed on different horizontal planes, which uses a combination of induction heating and inductive coupling, called inductively coupled heating. The system uses a single primary inductor acting as a transmitter to transfer power to a secondary inductor attached to the bottom load, which is connected electrically with a third inductor that heats the top load. Since power of the whole system is supplied by a simple half-bridge inverter, the ratio of the delivered power to each of the loads, which is critical for cooking results, is entirely dependent on the system's geometry, coil's number of turns, and compensation capacitors. A finite-element model is used to simulate the magnetic fields generated by inductor currents and calculate the impedance matrix. With the impedance, capacitor values and inductors’ number of turns are selected with the objective of achieving a high power ratio between the top and bottom zones, as well as minimizing stress in the electronics. First, a prototype was built to validate the impedance results in the small-signal regime, and then, the full power regime was used to verify power and current simulations


  • Open Access

    EMI Reduction Via Resonator Coils in Glassless Integrated Domestic Induction Systems

    by Emilio Plumed, Ignacio Lope, Jesus Acero

    This paper explores the magnetic flux emissions of induction heating systems compared with inductively coupled heating systems. Inductively coupled heating uses a resonator coil attached to the ferromagnetic load in order to improve energy transfer from the appliance to the load. The magnetic flux emissions of both kinds of systems are simulated, and their dependence on coil current and turn number is outlined. The paper focuses on emitted near field, whose measurement and limits are determined by norm. Several prototypes are developed and tested to verify the simulations.


  • Induction Heating Adaptation of a Different-Sized Load With Matching Secondary Inductor to Achieve Uniform Heating and Enhance Vertical Displacement

    by Emilio Plumed, Ignacio Lope, Jesus Acero

    This paper presents an Inductively Coupled Heating application, that is, a combination of Wireless Power Transfer and Induction Heating. The addition of a secondary inductor with resonant capacitor directly beneath and attached to the ferromagnetic load allows to improve Induction Heating adaptation of loads of different sizes to the primary inductor, enhancing power distribution and extending load distance while avoiding increased power losses and stress on electronic components. The extended distance can be used to implement the seamless induction concept, where the typical ceramic glass is substituted by the kitchen surface itself. Finite Element Analysis simulations are carried out to determine the suitability of each possible design, and a scoring system is applied to determine the optimal solution, bearing in mind the delivered power, power factor, power distribution and efficiency. A near optimal design is chosen to develop as a prototype. The prototype is tested under working conditions up to 3680 W at several distances, validating the simulations' impedance parameters and verifying power distribution with a water boiling test and a dry test with a thermographic camera.


  • Open Access

    Analysis and Modeling of the Forces Exerted on the Cookware in Induction Heating Applications

    by Jesus Acero, Ignacio Lope, Claudio Carretero, Jose M. Burdio

    We present a semianalytical model for calculating the forces exerted on cookware in domestic induction heating applications. The developed model is based on the Maxwell's stress tensor and is also based on the existing semianalytic expressions of the electromagnetic fields in planar induction heating systems, which are expressed in terms of Fourier-Bessel series. Taking advantage of the axial symmetry of usual domestic induction heating systems, the flux of the vertical component of the Maxwell's stress tensor is analytically integrated and the vertical force is obtained. The proposed model captures both eddy currents and magnetization that occurs in typical ferromagnetic cookware. The model is verified by means of two-dimensional Finite Element simulations and also is tested by means of measurements of the change of the weight experimented by cookware due to the forces during the heating process.


  • Open Access

    Adapting of Non-Metallic Cookware for Induction Heating Technology via Thin-Layer Non-Magnetic Conductive Coatings

    by J. Acero, I. Lope, C. Carretero, J. M. Burdio

    We analyze the feasibility of heating non-metallic cookware, unappropriate for heating by means of induced currents, with the purpose of extending the applicability range of the current induction heating cooktops. In order to turn materials as glass, ceramic, wood or plastic into suitable for the induction heating technology, we propose the use of thin layers of a metal (not necessarily a ferromagnetic material) which can be deposited on a surface by means of a thin or thick layer technology. For this purpose, the inductive performance of these layers is investigated by means of an analytical electromagnetic model, finite element simulations and experimental measurements. Calculations point out that for a specific induction arrangement working at a fixed frequency, it exists a thickness which maximizes the induction efficiency for each layer material. The suitability of this result is tested by means of a set of samples with copper thin layers whose thicknesses range from one hundred of nanometers to tens of micrometers, which are implemented using a phase vapor deposition (PVD) technology. The obtained induction efficiency and equivalent resistance are compared with those obtained with conventional ferromagnetic materials. As a proof of concept, the inner and outer bottoms of two glass pots are covered with a copper layer of 2 μm, and 1.5 μm, respectively, and 1 kW is inductively supplied by means of a series resonant inverter, reaching the boiling water conditions


  • Design of a Three Inductor System with One Externally Fed for an Inductively Coupled Heating Application

    by Emilio Plumed, Ignacio Lope, Jesus Acero, Jose Miguel Burdio

    This paper introduces the design of a three inductor system that uses a combination of induction heating and wireless power transfer, called inductively coupled heating, in order to heat an additional zone while feeding only one of the inductors. Since no more degrees of freedom are added, the delivered power to the second zone is entirely dependant on the system's geometry and resonant capacitors. Therefore, the ratio of the delivered power to each of the zones becomes very relevant to the design. A finite element model is used to simulate the magnetic fields generated by inductor currents and calculate the impedance matrix. With the impedance, capacitor values are selected with the objective of achieving a high power ratio between the second and first zone, as well as minimizing stress in the electronics. A prototype was used to validate the impedance results.