OPOksana Pustovoitova

Oksana Pustovoitova

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Oksana Pustovoitova has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Influence of dynamic loading parameters on soil foundation deformation

    by Vadym Alecksandrovych, Olha Havryliuk, Armen Atynian, Oksana Pustovoitova, Lyudmila Haponova

    Problem.. The study addresses the insufficiently explored aspects of additional settlements in sandy foundation soils under dynamic loads, particularly those following harmonic law vibrations. While static load-induced deformations are well-documented, the long-term effects of cyclic dynamic loading on cohesionless soils remain poorly understood. This knowledge gap is critical for ensuring the stability of vibration-prone structures like turbine units, industrial foundations, and transportation infrastructure, where even minor additional settlements can lead to operational failures or structural damage. Goal. The primary objective is to establish quantitative relationships between the increased deformability of sandy foundation soils and key parameters of forced vibrations, including frequency, amplitude, duration, and loading history. This research aims to develop improved predictive models for dynamic settlement that can be incorporated into modern geotechnical design practices, ultimately enhancing the safety and service life of structures subjected to vibrational loads. Methodology. The comprehensive research methodology combines: Controlled laboratory tray tests using standardized sand samples under precisely calibrated harmonic loads; Field vibro-stamp experiments on natural cohesionless soil deposits to validate laboratory findings under real-world conditions; Advanced analytical methods including multivariate regression analysis and dimensional analysis to derive predictive coefficients. Results. The experimental investigations yielded several significant findings: Dynamic loads induce distinct vibrocreep phenomena in sandy soils, causing progressive settlement accumulation even when static load conditions remain constant; Settlement magnitude demonstrates a power-law dependence on vibration frequency, with critical thresholds observed at 15-25 Hz for medium sands. Originality. This study makes several novel contributions: Development of empirical coefficients specifically tailored for predicting dynamic settlement in cohesionless soils; First comprehensive validation of the relationship between harmonic load parameters and long-term vibrocreep development. Practical value. The research outcomes have direct engineering applications: Enabling more accurate preliminary estimation of foundation settlement for vibration-sensitive structures; Providing a scientific basis for optimizing dynamic load thresholds in geotechnical design codes; Supporting the development of improved vibration mitigation strategies for critical infrastructure; Establishing a framework for condition assessment of existing foundations subjected to long-term dynamic loads

  • Open Access

    IMPACT OF THE GLUE LAYER PROPERTIES ON THE STRESS-STRAIN STATE OF THE GLUE ANCHOR FOR THE STEEL ROD IN CONCRETE

    by Сергій Михайлович Золотов, Oksana Pustovoitova, Liudmyla Trykoz, Світлана Миколаївна Камчатна, Serhii Savisko

    У статті розглянуті питання розподілення напружень і переміщень вздовж сталевого анкера, закріпленого в бетоні полімерним зв’язуючим – акриловим компаундом. Встановлено, що максимальні значення дотичних, радіальних і колових напружень, що більш повно характеризують роботу з'єднання, змінюються залежно від міцнісних характеристик клейового шару та його товщини за експоненціальним законом. Отримані результати напружень у будь-якій точці клейового з’єднання дають змогу запропонувати методологію проєктування сталевих стрижнів у бетоні, закріплених полімерами.


  • Open Access

    PLACEMENT OPTIMIZATION OF THE POINTS OF THE CONDITIONAL REPER NETWORK FOR RAILWAY CURVES

    by Костянтин Анатолійович Мамонов, Oleksandr Saiapin, Yevhen Orel, Світлана Миколаївна Камчатна, Oksana Pustovoitova

    Railway facilities are responsible and complex structures related to the safety ofpassenger traffic and cargo transportation. To ensure the reliability of all systems, the railway trackneeds continual control of its geometric parameters. Railways require high accuracy of survey andmonitoring both at the construction stage and at the operation stage. Such control can be carried outusing control points of the geodetic benchmark network. These control points must be located nearthe railway track to provide it in the design position and in proper working condition. That is whythe development of "own" railways benchmark network is topical.The purpose of this article is to create a mathematical basis for calculating the locations ofown repers near the railway. These benchmarks will be control points that will be used by track-operation stations, track machine stations, engineering and geodetic departments, track-surveyingstations, services and departments, as well as project and construction organizations duringresearch, design, operation, repair, reconstruction, or new construction. This will keep the track ingood condition and be used for leveling the track during repair work. The paper considers thecalculation method for the placement of control points of the conditional benchmark network on thecurved section of the railway. The novelty is the usage of the mean-value theorem of integral calculusto calculate the coordinates of the curve independently of the national geodetic network. The creationof "own" conditional benchmark network allows railways to perform the pegging of lines and curvesregardless of the presence or remoteness of control points of the local or state geodetic network. Afterchoosing a conditional benchmark, the coordinates of the railway curve, which is divided into 5 parts,were calculated. It is shown that the number of points does not affect the accuracy of determining thecoordinates. Thus, fewer rappers can be dispensed, and the speed of the pegging will increase. Thepolar coordinates for the two polar distances from the conventional benchmark have been determined. It is established that the use of the mean-value theorem of the integral calculus to findthe coordinates of a point gives more accurate data, since this method does not involve replacing thearc with a chord. The described method of determining polar coordinates from any point of one'sown network of conditional benchmarks is of practical importance. After deviating the axis of thetrack from the movement of trains, maintenance workers can put it back without additionalcalculation.

  • Point disposition of the conditional benchmark network and the railway curve elements

    by K. Mamonov, O. Saiapin, Y. Orel, S. Kamchatnaya, O. Pustovoitova

    Control of geodetic parameters is very important for traffic safety on the railways. Such control must be performed regularly because of the deviation of the track axis due to train traffic. The purpose of the article is the development of a mathematical rationale for the placement of railway benchmarks for the creation of the ‘own’ conditional benchmark network of the railway. These permanent repers are the basic points for both the construction stage and operation stage. The method is described and the curve coordinates from any point of the conditional benchmark network of the railway have been obtained.


  • Open Access

    Water absorption kinetics of bitumen modified cement mortars

    by Liudmyla Trykoz, Maryna Rezunenko, Oksana Pustovoitova, Victoria Semenova-Kulish, Dmytro Borodin

    Concrete permeability is a major factor that affects durability and reliability of structures – bridges, tunnels, culvert pipes, etc. It is important to identify effective methods of protection of such structures against water penetration, for example by using a modifying substance. Samples of cement mortar composites were used for water absorption simulation. Bitumen emulsion was used as a modifying agent. According to the water absorption kinetics, the following parameters of the pore microstructure of the mortar composite were estimated: the index of mean size of open capillary pores, closed porosity, and the index of size uniformity. The research has shown that the addition of bitumen emulsion decreases the pore space and macrocapillaries (from 23.91% to 6.61%), water absorption (3 times), and the index of mean size of open capillary pores (from 0.69 to 0.3) of modified mortars.


  • Open Access

    Impact of fillers for acrylic compositions on their stability in aggressive mediums and adhesive strength

    by L Trykoz, S Kamchatnaya, O Pustovoitova, I Saiapina, D Borodin

    This paper aims to reveal the change of diffusion coefficient and permeability of the acrylic composition with different types of fillers (such as cement, sand, mica, and talc) in the various aggressive mediums. Also, the adhesive strength was determined as the maximal stress caused by detaching metal plate from the surface of the concrete. To evaluate the stability of the compositions, the samples of the acrylic compositions were saturated with acid and alkali solutions during a certain time. Basing on the mass change, the coefficients of diffusion, sorption, and permeability were calculated. The sand filled acrylic composition showed the least sorption (0.2%) and water permeability (0.008 g×cm–1×s–1), as well as the highest adhesion strength (53.2 MPa). However, all studied compositions satisfy the requirements of the current permeability standards, and they can be used for construction protection from the aggressive environment action. It is important for the durability of the structures as it will prolongate their operative time, as well as reduce the operating and repair costs.

  • STRENGTH OF CLT PANELS AT TENSION AND COMPRESSION ALONG GRAIN DIRECTION

    by O.M. Beketov National University of Urban Economy in Kharkiv, А. Bidakov, E. Raspopov, O. Pustovoitova, B. Strashko

    Міцність при згині із площини та міцність при розтягу вздовж волокон залежить від характеристичної міцності дошок при розтягу вздовж волокон, їх коефіцієнту варіації і кількості дошок як системи, або ефективного поперечного перерізу ПКД панелі навантажений вздовж волокон. На сьогонішній день виконані дослідження з оцінки міцності при розтягу вздовж волокон ПКД панелей, але відсутні коефіцієнти, що враховують можливе розподілення навантаження аналогічного для міцності при згині із площини панелі. Нехтування шарами поперечних дошок при визначенні площі перерізу нетто Anet підкреслює раціональність впровадження неоднорідної структури панелі виходячи з класу міцності дошок, аналогічно до комбінованої клеєної деревини для балок, де дошки високих класів міцності розташовуються у верхній і нижній чверті або третині поперечного перерізу. Показана у цій роботі методологія для розрахунку міцності неоднорідних ПКД панелей показує свою ефективність, яка призводить до оптимізації і економії матеріалу. Ортогональна структура склеєних дошок у ПКД панелі при стиску поперек волокон призводить до показників міцності та модуля пружності вище на 30%, ніж для клеєної деревини, як це вказано у публікації Brandner та Schickhofer (2014) [1], де також розглянуто модель дисперсії напружень, раніше розробленої van der Put (1991, 2008, 2012) [4-6] згідно якої дисперсія напружнь вздовж волокон складає 45° і 15° поперек волокон. Дослідження зразків ПКД панелей показали, що наявність щілин та компенсаційних пропилів між дошками знижують параметр дисперсії майже у 2 рази. При стандартних товщинах дошок та найвності щілин дисперсія напружень при стиску поперек площини панелі усереднено становить 35°.


  • ADVANTAGES AND DISADVANTAGES OF G-METHOD FOR CALCULATION OF CLT PANELS STRENGTH BY BENDING

    by O. M. Beketov National University of Urban Economy in Kharkiv, A. Bidakov, E. Raspopov, O. Pustovoitova, B. Strashko

    Поперечна клеєна деревина (ПКД) або CLT є новим будівельним матеріалом, який широко впроваджується у будівництві багатоповерхових житлових та офісних будівель. Цей матеріал набув широке розповсюдження у країнах Європи, США та Канаді і активно використовується вже напротязі 20 років. На сучасному етапі розвитку ПКД панелей тільки націоальний стандарт німеччини DIN EN 1995-1-1/NA (2010) та стандарт Австрії ÖNORM B 1995-1-1 (2014) з проектування дерев'яних конструкцій містить рекомендації щодо розрахунку та конструювання будівель з ПКД панелей. Розрахунок ПКД панелей при різних видах напруженого стану можливо виконувати лише на основі технічних заключень лабораторій та сертифікатів продуктів які містять вказівки та поправочні величини для розрахунків ПКД панелей конктерного виробника. Наступна редакція Єврокоду-5 у 2022 році буде мати суттєві нормативні вказівки та вимоги для проектування і розрахунку будинків з використанням ПКД панелей. Існує три методи розрахунку міцності ПКД панелей при згині, кожна з яких базується на певній схемі апрокисмації: гамма-метод, метод Тимошенко та метод зсувної аналогії. Гамма-метод розглядає ПКД панель як балку на підатливих зв’язках, аналогчно балці системи Деревягіна на пластинчатих шпонках або кубишках Кюблера, де поперечні шари дошок розглядаються як підатливі звязки і не враховуються при обчисленні геометричних характеристик поперечних перерізів ПКД панелей. Кожна методика має свої переваги та недоліки, оскільки має цілу низку певних припущень для спрощення обчислень. У даній роботі висвітлені переваги та недоліки гамма-методу, який має найбільше розповсюдження ніж інші методики і міститься у багатьох технічних заключеннях різних виробників ПКД панелей. Аналіз недоліків цієї методики дозволяє уникнути низку неточностей результатів розрахунку.


  • Open Access

    Features of the shear analogy method for calculating the bending strength of clt panels

    by A. M. Bidakov, O. M. Pustovoitova, Ye. A. Raspopov, B. O. Strashko

    Постановка проблеми. Міцність панелей з поперечної клеєної деревини (ПКД) або CLT під час згину визначається γ-методом, методом Тимошенко та методом зсувної аналогії. Останній розглянуто у цій публікації та передбачає аналіз міцності шляхом розгляду ПКД панелі як системи повздовжніх стрижнів, з’єднаних між собою піддатливим поперечним шаром дошок. Залежно від конфігурації складових поперечного перерізу враховується відповідно жорсткість стержнів. Повороти поперечного перерізу відповідають класичній теорії стрижня Бернуллі. Метод зсувної аналогії відповідає γ-методу у контексті симетричних перерізів і розглядається як наближений підхід, який видає наближене рішення. Мета роботи полягає у теоретичному аналізі методу зсувної аналогії, що застосовується для розрахунку міцності ПКД або CLT панелей під час згину. Модулі зсуву деревини та будівельних матеріалів на її основі мають значну різницю між величиною модуля зсуву та модуля пружності, то ПКД панель можливо розглядати як промінь, що складається із двох гнучко з'єднаних поперечних шарів (промінь А і В), через що теорія балок Бернуллі застосовується для визначення деформацій згинальних елементів з урахуванням деформацій кожного шару дошок. Висновки. Метод зсувної аналогії дає точні результати порівняно із симетричним поперечним перерізом у двох або трьох частинах і, на відміну від γ-методу враховує довільні системи та навантаження. Визначення впливу зосереджених навантажень та внутрішніх опор для нерозрізних балок відносно точні і метод аналогії зсуву можна розглядати як ексклюзивний підхід, який здатний досить точно визначати існуючі максимуми напружень під час згину.


  • Open Access

    THE INFLUENCE OF CLT PANEL PRODUCTION TECHNOLOGY ON THEIR STRENGTH AND RIGIDITY

    by A. Bidakov, E. Raspopov, О. Pustovoitova, В. Strashko, B. Strashko

    In this paper considered the technological features of the production of CLT panels with focus on overview of the thicknesses of the boards and their width in cross-section in the panel on their character of pressing and selection of adhesive systems. The quality of wooden building materials based on boards is highly dependent on many technological operations, and above all on the method of pressing and the type of adhesive system. Generally accepted technological features of the production of glued laminated timber are significantly different from the technology of production of CLT panels, since the latter work as plates, and the glued laminated timber elements are the core elements of frames of different types of buildings. For completeness of analysis of CLT panels as a structural material methods of research of panels at different types of stress states are given according to the results of which characteristics of strength and rigidity of panels are assigned and correspond to a certain class of strength of CLT of panels. As a rule, at the present stage of the development of panels, all boards have the same strength class, which greatly simplifies the calculation and increases the homogeneity of the panels, as the structure with mutually transverse layers of boards. Large dimensions and specificity of production of panels of panels has a number of tolerances and boundary parameters that affect the quality of panels and their strength characteristics, which is largely due to the tight control of all technological operations in the manufacture of panels of different thicknesses. The cross laminated timber or CLT in the construction market has sparked a new expansion. The manufacturing practice of PKD panels has been around for more than 20 years in European countries, most notably in Austria, Germany and Switzerland. Keywords: cross laminated timber, CLT, producing technology, stress reliefs, boards edge gluing, rolling shear, board thickness, glue systems.