Márton Kuslits
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Márton Kuslits has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Krisztian Horvath
Széchenyi István University, Győr, Hungary, Hungary
6 shared publications Dieter Bestle
Chair of Engineering Mechanics and Vehicle Dynamics, Brandenburg University of Technology, Cottbus, Germany
3 shared publicationsSzilárd Lovas
Széchenyi István University, Győr, Hungary
1 shared publication
Latest Publications
- 16 August 2020
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 60 (1) , 73-95
Multiobjective performance optimisation of a new differential steering concept
Differential steering is an emerging steering concept based on traction force differences between left and right sides of vehicles equipped with independently actuated wheels. Actually, this concept is only used to support classical vehicle designs utilising rack and pinion steering components. However, it may fully substitute such devices to reduce complexity and cut down costs. Since we do not have well-established design rules for such kind of vehicles, this paper will overcome the missing experience and explore the general applicability of such a new steering concept by using multiobjective optimisation. Three design objectives and three constraints are defined with respect to the dynamic, steady-state and low-speed steering performance of the vehicle. Since mechanical and control parts are strongly coupled, their parameters are optimised simultaneously by a multiobjective genetic algorithm aided by iteratively updated neural network-based response surface metamodels. Optimisation results in a variety of technically feasible Pareto-optimal designs. Investigation of a particular optimal design shows that a vehicle with differential steering is able to provide convincing steering performance.
- 16 August 2020
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 60 (1) , 73-95
Multiobjective performance optimisation of a new differential steering concept
Differential steering is an emerging steering concept based on traction force differences between left and right sides of vehicles equipped with independently actuated wheels. Actually, this concept is only used to support classical vehicle designs utilising rack and pinion steering components. However, it may fully substitute such devices to reduce complexity and cut down costs. Since we do not have well-established design rules for such kind of vehicles, this paper will overcome the missing experience and explore the general applicability of such a new steering concept by using multiobjective optimisation. Three design objectives and three constraints are defined with respect to the dynamic, steady-state and low-speed steering performance of the vehicle. Since mechanical and control parts are strongly coupled, their parameters are optimised simultaneously by a multiobjective genetic algorithm aided by iteratively updated neural network-based response surface metamodels. Optimisation results in a variety of technically feasible Pareto-optimal designs. Investigation of a particular optimal design shows that a vehicle with differential steering is able to provide convincing steering performance.
- Open Access
- 10 February 2020
- Published by Springer Nature in Electrical Engineering
- Vol. 102 (3) , 1103-1116
Model-based control algorithm development of induction machines by using a well-defined model architecture and rapid control prototyping
This paper presents a new control algorithm development approach for induction machines by using model-based design and a systematically built model architecture implemented in MATLAB/Simulink. The model architecture follows a three-layer structure, and it is developed according to the principle of functional decomposition and the needs of reusability and expandability. The first model layer consists of elementary model and algorithm components, the second contains a machine simulation model and a field-oriented control (FOC) algorithm, built upon the first layer’s components, and the third realises the executable models by connecting the models and algorithms defined in the second layer. Furthermore, rapid control prototyping (RCP) is discussed as an experimental validation method, and an experimental setup with RCP is also introduced. The application of the presented methods is demonstrated by simulations as well as by experiments, and by using a control algorithm based on FOC as an example.
- 10 February 2020
- Published by Springer Nature in Electrical Engineering
- Vol. 102 (3) , 1103-1116
Open AccessModel-based control algorithm development of induction machines by using a well-defined model architecture and rapid control prototyping
This paper presents a new control algorithm development approach for induction machines by using model-based design and a systematically built model architecture implemented in MATLAB/Simulink. The model architecture follows a three-layer structure, and it is developed according to the principle of functional decomposition and the needs of reusability and expandability. The first model layer consists of elementary model and algorithm components, the second contains a machine simulation model and a field-oriented control (FOC) algorithm, built upon the first layer’s components, and the third realises the executable models by connecting the models and algorithms defined in the second layer. Furthermore, rapid control prototyping (RCP) is discussed as an experimental validation method, and an experimental setup with RCP is also introduced. The application of the presented methods is demonstrated by simulations as well as by experiments, and by using a control algorithm based on FOC as an example.
- Open Access
- 17 November 2018
- Published by Walter de Gruyter GmbH in Power Electronics and Drives
- Vol. 3 (1) , 129-144
Dynamic Performance of Estimator-based Speed Sensorless Control of Induction Machines Using Extended and Unscented Kalman Filters
This paper presents an estimator-based speed sensorless field-oriented control (FOC) method for induction machines, where the state estimator is based on a self-contained, non-linear model. This model characterises both the electrical and the mechanical behaviours of the machine and describes them with seven state variables. The state variables are estimated from the measured stator currents and from the known stator voltages by using an estimator algorithm. An important aspect is that one of the state variables is the load torque and, hence, it is also estimated by the estimator. Using this feature, the applied estimator-based speed sensorless control algorithm may be operated adequately besides varying load torque. In this work, two different variants of the control algorithm are developed based on the extended and the unscented Kalman filters (EKF, UKF) as state estimators. The dynamic performance of these variants is tested and compared using experiments and simulations. Results show that the variants have comparable performance in general, but the UKF-based control provides better performance if a stochastically varying load disturbance is present.
- 17 November 2018
- Published by Walter de Gruyter GmbH in Power Electronics and Drives
- Vol. 3 (1) , 129-144
Open AccessDynamic Performance of Estimator-based Speed Sensorless Control of Induction Machines Using Extended and Unscented Kalman Filters
This paper presents an estimator-based speed sensorless field-oriented control (FOC) method for induction machines, where the state estimator is based on a self-contained, non-linear model. This model characterises both the electrical and the mechanical behaviours of the machine and describes them with seven state variables. The state variables are estimated from the measured stator currents and from the known stator voltages by using an estimator algorithm. An important aspect is that one of the state variables is the load torque and, hence, it is also estimated by the estimator. Using this feature, the applied estimator-based speed sensorless control algorithm may be operated adequately besides varying load torque. In this work, two different variants of the control algorithm are developed based on the extended and the unscented Kalman filters (EKF, UKF) as state estimators. The dynamic performance of these variants is tested and compared using experiments and simulations. Results show that the variants have comparable performance in general, but the UKF-based control provides better performance if a stochastically varying load disturbance is present.
- 26 August 2018
- Published by ASME International
Symbolic Linearized Equations for Nonholonomic Multibody Systems With Closed-Loop Kinematics
Multibody systems and associated equations of motion may be distinguished in many ways: holonomic and nonholonomic, linear and nonlinear, tree-structured and closed-loop kinematics, symbolic and numeric equations of motion. The present paper deals with a symbolic derivation of nonlinear equations of motion for nonholonomic multibody systems with closed-loop kinematics, where any generalized coordinates and velocities may be used for describing their kinematics. Loop constraints are taken into account by algebraic equations and Lagrange multipliers. The paper then focuses on the derivation of the corresponding linear equations of motion by eliminating the Lagrange multipliers and applying a computationally efficient symbolic linearization procedure. As demonstration example, a vehicle model with differential steering is used where validity of the approach is shown by comparing the behavior of the linearized equations with their nonlinear counterpart via simulations.
- 26 August 2018
- Published by ASME International
Symbolic Linearized Equations for Nonholonomic Multibody Systems With Closed-Loop Kinematics
Multibody systems and associated equations of motion may be distinguished in many ways: holonomic and nonholonomic, linear and nonlinear, tree-structured and closed-loop kinematics, symbolic and numeric equations of motion. The present paper deals with a symbolic derivation of nonlinear equations of motion for nonholonomic multibody systems with closed-loop kinematics, where any generalized coordinates and velocities may be used for describing their kinematics. Loop constraints are taken into account by algebraic equations and Lagrange multipliers. The paper then focuses on the derivation of the corresponding linear equations of motion by eliminating the Lagrange multipliers and applying a computationally efficient symbolic linearization procedure. As demonstration example, a vehicle model with differential steering is used where validity of the approach is shown by comparing the behavior of the linearized equations with their nonlinear counterpart via simulations.
- 1 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 744-749
Parameter Sensitivity Analysis Method for Speed Sensorless Induction Machine Drives Based on Unscented Kalman Filter
This paper presents a new method for determining the steady-state machine parameter sensitivities of induction machine speed sensorless control algorithms, which are utilizing unscented Kalman filter (UKF) and direct rotor field oriented control (DRFOC). Sensitivity influence of the UKF is investigated by alternative noise parameters and pointed out that selection of noise parameters may influence the flux and torque sensitivities of the entire system with respect to stator resistance variations. In order to obtain a better picture, the sensitivities are calculated for various operating points resulting in sensitivity maps. For this, a computationally efficient calculation method is applied by using the steady-state system equations.
- 1 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 744-749
Parameter Sensitivity Analysis Method for Speed Sensorless Induction Machine Drives Based on Unscented Kalman Filter
This paper presents a new method for determining the steady-state machine parameter sensitivities of induction machine speed sensorless control algorithms, which are utilizing unscented Kalman filter (UKF) and direct rotor field oriented control (DRFOC). Sensitivity influence of the UKF is investigated by alternative noise parameters and pointed out that selection of noise parameters may influence the flux and torque sensitivities of the entire system with respect to stator resistance variations. In order to obtain a better picture, the sensitivities are calculated for various operating points resulting in sensitivity maps. For this, a computationally efficient calculation method is applied by using the steady-state system equations.
- 22 May 2018
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 57 (4) , 520-542
Modelling and control of a new differential steering concept
This paper presents a new steer-by-wire concept using an all-wheel drive vehicle layout with in-wheel motors while completely omitting the application of any dedicated steering device. Steering is based on the so-called differential steering principle which generates the necessary steering moment about the kingpins by a traction force difference between left and right sides of the vehicle. In order to investigate the behaviour of the vehicle and to design the underlying control algorithms, a planar vehicle model is presented, where the vehicle is described as constrained non-holonomic system requiring a special treatment. A state feedback linear controller for controlling of the lateral dynamics of the vehicle at higher speeds and a simple PI angle controller for low-speed manoeuvring are developed. The resulting behaviour of the system is investigated by various simulation experiments demonstrating a comparable steering performance of the new steering concept as that of conventional passenger cars.
- 22 May 2018
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 57 (4) , 520-542
Modelling and control of a new differential steering concept
This paper presents a new steer-by-wire concept using an all-wheel drive vehicle layout with in-wheel motors while completely omitting the application of any dedicated steering device. Steering is based on the so-called differential steering principle which generates the necessary steering moment about the kingpins by a traction force difference between left and right sides of the vehicle. In order to investigate the behaviour of the vehicle and to design the underlying control algorithms, a planar vehicle model is presented, where the vehicle is described as constrained non-holonomic system requiring a special treatment. A state feedback linear controller for controlling of the lateral dynamics of the vehicle at higher speeds and a simple PI angle controller for low-speed manoeuvring are developed. The resulting behaviour of the system is investigated by various simulation experiments demonstrating a comparable steering performance of the new steering concept as that of conventional passenger cars.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Optimization-based parameter tuning of unscented Kalman filter for speed sensorless state estimation of induction machines
State estimation of induction machines may be a difficult problem, due to the non-linear behavior of theirs. For non-linear state estimation, the unscented Kalman filter (UKF) is a well-known extension of the linear Kalman filter. Operation of the UKF algorithm strongly depends on the process and measurement noise covariance parameters of the estimator. Determination of these parameters is not straightforward and can be difficult, especially if the number of state variables and hence the system complexity is relatively high. In this paper, the UKF algorithm is applied for speed sensorless state estimation of induction machines in such a way that seven state variables are estimated from the measured stator currents and from the known excitation voltages. In order to tune the noise parameters of the UKF, a new, optimization-based method is presented. This tuning method provides adequate behavior for the observer beside difficult operating conditions as it has been shown by simulation experiment.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Optimization-based parameter tuning of unscented Kalman filter for speed sensorless state estimation of induction machines
State estimation of induction machines may be a difficult problem, due to the non-linear behavior of theirs. For non-linear state estimation, the unscented Kalman filter (UKF) is a well-known extension of the linear Kalman filter. Operation of the UKF algorithm strongly depends on the process and measurement noise covariance parameters of the estimator. Determination of these parameters is not straightforward and can be difficult, especially if the number of state variables and hence the system complexity is relatively high. In this paper, the UKF algorithm is applied for speed sensorless state estimation of induction machines in such a way that seven state variables are estimated from the measured stator currents and from the known excitation voltages. In order to tune the noise parameters of the UKF, a new, optimization-based method is presented. This tuning method provides adequate behavior for the observer beside difficult operating conditions as it has been shown by simulation experiment.
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 57, 523-528
Speed sensorless field oriented control of induction machines using unscented Kalman filter
In this paper, an observer-based speed sensorless field oriented control (FOC) algorithm is presented for induction machines. The state observer is based on a new, detailed observer model which describes the machine with seven state variables, i.e. with seven equations. Since these equations are strongly non-linear, the applied observer algorithm is the unscented Kalman filter (UKF). Using the advantages of the detailed non-linear model and the UKF algorithm, the state variables can be estimated adequately, including the rotor flux position. Using these variables a speed sensorless FOC structure has been developed.
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 57, 523-528
Speed sensorless field oriented control of induction machines using unscented Kalman filter
In this paper, an observer-based speed sensorless field oriented control (FOC) algorithm is presented for induction machines. The state observer is based on a new, detailed observer model which describes the machine with seven state variables, i.e. with seven equations. Since these equations are strongly non-linear, the applied observer algorithm is the unscented Kalman filter (UKF). Using the advantages of the detailed non-linear model and the UKF algorithm, the state variables can be estimated adequately, including the rotor flux position. Using these variables a speed sensorless FOC structure has been developed.
- 24 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 133-138
Model-Based development of induction motor control algorithms with modular architecture
Development of control algorithms for electrical machines may be a difficult procedure if functional safety, software quality, reusability and expandability come into scope. These properties might be required in both of research and industrial development projects. State of the art methods and tools like model-based design (MBD) and automated code generation may help to meet these requirements. In this paper, MBD methods and a modular, reusable model architecture are presented for implementation of field oriented control (FOC)-based controller software for induction motors.
- 24 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 133-138
Model-Based development of induction motor control algorithms with modular architecture
Development of control algorithms for electrical machines may be a difficult procedure if functional safety, software quality, reusability and expandability come into scope. These properties might be required in both of research and industrial development projects. State of the art methods and tools like model-based design (MBD) and automated code generation may help to meet these requirements. In this paper, MBD methods and a modular, reusable model architecture are presented for implementation of field oriented control (FOC)-based controller software for induction motors.