Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yong Li has a total of 73 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Embedded Delay-Coordinate Predictive Damping for Speed Ripple Attenuation in a Motor–Reducer Flexible Drive

    by Jing Nie, Yong Li

    Speed ripple attenuation in geared flexible drives requires control of synchronous components and residual fluctuations within an existing embedded control architecture. This paper develops a five-state delay-coordinate predictive damping controller (D5–PD) that adds auxiliary q-axis current to a proportional–integral (PI)-regulated drive. Direction-specific models are identified from drive speed history and auxiliary current records with exact delay shifts. A three-step output-weighted design is solved offline and deployed as five-coefficient feedback with scalar scheduling and current limits, at a 1 ms auxiliary update period on an F28379D. Experiments compare PI, six-branch multi-resonant control (MR), and D5–PD under six conditions with three runs per controller. At +300 r/min and +1 A, D5–PD reduces mean speed ripple root mean square (RMS) by 38.83% relative to PI and 5.61% relative to MR at nearly equal auxiliary command alternating-current (AC) RMS. Its load current-normalized responses at 2 and 8 Hz are 37.39% and 60.17% lower than MR without disturbance-specific retuning. Total ripple is lower than PI in all six conditions and MR in five; residual RMS is lower than MR throughout. A separate 0.20 A benchmark with six records per method gives 2.12% lower total ripple and 7.68% lower command RMS than proportional ripple damping. These results demonstrate an embedded auxiliary damping implementation and characterize its tradeoffs with frequency-selective and proportional feedback in terms of total ripple, residual fluctuations and command demand.

  • Robust positive and negative obstacle detection algorithm in unstructured outdoor environments for unmanned vehicle

    by Yong Li, Xiaoxin Yang, Bin Hu, Yaping Qu

    In unstructured off-road environments, autonomous driving perception systems must be capable of identifying both positive and negative obstacles. Current methods, such as ground point cloud segmentation algorithms or direct feature extraction from obstacles, are often susceptible to interference from environmental terrain. To address these challenges, this paper proposes a multi-sensor fusion approach. For positive obstacle detection, the Patchwork++ algorithm is robustly enhanced by integrating IMU data and an Adaptive Smoothing Module (ASM). Additionally, dedicated operators are introduced to model mound-like terrains and extract mound point clouds, thereby achieving higher-precision ground point cloud segmentation. For negative obstacle detection, a side-mounted LiDAR configuration is employed to improve the radial resolution of point clouds in front of the vehicle. To enhance the algorithm’s adaptability to various LiDAR types, a geometric model of the LiDAR scanning structure is developed, enabling real-time generation of high-quality simulated ring data through online iteration. This facilitates synchronized detection across heterogeneous LiDAR sensors. Subsequently, geometric features are extracted from the point clouds and integrated with voxel-based Bayesian inference, resulting in a robust negative obstacle detection algorithm. The proposed method was validated using a self-constructed unstructured terrain ground truth dataset and the open-source RELLIS-3D dataset. Experimental results demonstrate that the proposed approach outperforms state-of-the-art methods in both ground point cloud segmentation and negative obstacle point cloud extraction. Finally, the integration of these two algorithms yields a robust positive and negative obstacle perception system for off-road environments, providing reliable support for subsequent decision-making, planning, and control tasks.

  • Open Access

    Semi-Supervised Cascade Head Pose Estimation for Drivers in Open-Pit Mining Trucks

    by Feng Jiang, Bin Hu, Yulong Liu, Xiaonian Chen, Wei Zhang, Yong Li

    Driver distraction causes accidents in mining trucks, posing significant safety risks in open-pit mining operations. Estimating the driver’s head pose is a key task for detecting distraction. However, accurate head pose estimation typically requires large amounts of high-quality annotated data. Obtaining a high-precision head pose estimation model under conditions of limited labeled data is challenging. To address the scarcity of annotated data in mining scenarios, this paper proposes a semi-supervised framework named the semi-supervised cascade head pose estimator (SemiCHPE) for driver head pose estimation. The framework adopts a two-stage cascade architecture: the first stage involves a semi-supervised head detector (HeaDet) for head detection, while the second stage comprises a semi-supervised head pose estimator (HPE) for pose estimation. Extensive experiments conducted on our proprietary dataset of mining truck drivers demonstrate that, using only 10% of the dataset, the proposed framework achieves an F1-Score of 99.3% for head detection and a mean absolute error (MAE) of 2.8° for head pose estimation. When deployed on an NVIDIA Orin NX platform within operational mining trucks, the framework attains real-time inference at 32 frames per second with an accuracy of 91.6%, validating its effectiveness for real-world deployment in intelligent mining transportation systems.

  • Electromagnetic-thermal coupled analysis of in-wheel motor with NSGA-based optimization water cooling structure for electric vehicle application

    by Yong Li, Feng Zhang, Keke Sheng, Wei Wu, Zhanwei Su, Xing Xu

    Traction motors with high power density are prone to excessive temperature rise, which negatively affects performance and reliability, making effective thermal management essential. In this study, a spiral water-cooling channel integrated into the stator support of an in-wheel motor is proposed to suppress temperature rise while maintaining acceptable hydraulic losses. Using computational fluid dynamics (CFD) with the finite volume method, the three-dimensional temperature field and flow characteristics of the motor cooling system were analyzed. A multi-objective optimization of the cooling structure is performed using the non-dominated sorting genetic algorithm II (NSGA-II), with winding temperature, inlet–outlet pressure difference, and surface heat transfer coefficient (HTC) selected as optimization objectives. The results show that the optimized spiral cooling structure reduces the maximum motor temperature by 4.23°C. The optimal design consists of four spiral water channels with a cross-sectional height of 10.3 mm, a width of 11.4 mm, and an inlet flow velocity of 1.05 m/s, achieving a balanced compromise between thermal effectiveness and hydraulic efficiency. Experimental validation conducted on a single-motor test platform demonstrates good agreement with the numerical results, confirming the feasibility and effectiveness of the proposed cooling strategy.

  • Fuzzy sliding model control approach for steering system of the tracked snow groomer considering the sliding characteristics

    by Yong Li, Wenlong Li, Yizhe Su, Yaping Qu, Pengfei Liu

    The snow groomer is an important equipment in ski resorts to build and maintain high-quality snow trails. Due to the special operating environment, there is less research data on the dynamics analysis and vehicle control of the snow groomer. Therefore, combined with the characteristics of the snow groomer, the mechanism of the steering motion process of the snow groomer is analyzed in this paper. The ideal steering model of the snow groomer and the steering model considering slip and slide characteristics are established respectively. The model is analyzed, and the relationship between the relative steering radius and slip degree, as well as between slide degree and track force in the steering process of the snow groomer, is obtained. The two models are compared and analyzed, revealing that the steering resistance of the steering model considering slip and sliding is smaller during the steering process. Subsequently, the driver’s driving intention is decoupled into the acceleration signal and steering signal during the steering process of the snow groomer, which is used to control the vehicle speed and yaw rate respectively. The designed PID controller and fuzzy sliding mode controller are employed to control the speed and yaw rate of the vehicle during steering. The simulation results show the fuzzy sliding mode controller achieves faster response and higher tracking accuracy, reducing response delay by approximately 0.2 s in simulations. Finally, the experimental platform of the tracked vehicle is established to verify the control effect of the designed controller. Experiments under straight, turning, and in situ steering conditions confirm that the fuzzy sliding mode controller improves response time by approximately 0.3 s compared to the PI controller. These findings provide a strong theoretical and experimental foundation for high-performance snow groomer control in complex environments.


  • Open Access

    High-performance control of permanent magnet synchronous motor using a finite-time sliding mode observer and super-twisting algorithm

    by Jing Nie, Yong Li, Gang Li

    To enhance the tracking performance of the permanent magnet synchronous motor (PMSM) drive system in the face of changing operating conditions, such as variations in internal parameters and external load disturbances, this study proposed a new composite control strategy that combines the super-twisting sliding mode controller (STSM) with the finite-time sliding mode observer (FTSMO). The proposed methodology synergistically integrates the enhanced tracking precision and robust disturbance rejection properties inherent to the second-order tracking-sliding mode (STSM) controller with an innovative finite-time sliding mode observer (FTSMO), thereby achieving significant improvements in system state estimation accuracy. The stability of the closed-loop PMSM drive system under the STSM+FTSMO framework is thoroughly analyzed and established using Lyapunov theory. The proposed composite control strategy effectiveness is confirmed through both simulations and experimental outcomes. These findings illustrate that the proposed approach significantly surpasses conventional control methods, especially in managing external disturbances within the PMSM system. Significant enhancements are evident in start-up response, robustness against load variations, convergence speed, and steady-state performance.

  • Sensorless control of permanent magnet synchronous motor based on interacting multiple model extended Kalman filter

    by Yong Li, Jiexin An, Han Hu, Xing Xu

    Aiming at the problems of low estimation accuracy and narrow application range of sensorless control caused by inverter nonlinearity and motor parameter error, this paper studies a sensorless control technology of permanent magnet synchronous motor based on an interactive multi-model extended Kalman filter algorithm to realize high-precision and high-performance sensorless control of a permanent-magnet synchronous motor. Firstly, considering the influence of inverter nonlinearity, the mathematical model of PMSM including inverter disturbance voltage is established. Secondly, an interactive multi-model extended Kalman filter observer is designed based on this model to achieve high-precision sensorless control of PMSM. Thirdly, the nonlinear disturbance voltage of the inverter is fed back to the control system for dead-time compensation, thus eliminating the voltage disturbance caused by the dead-time effect. Finally, simulation experiments and dual-motor towing experiments demonstrate the efficacy of the interactive multi-model extended Kalman filter sensorless control algorithm in mitigating the effects of dead time. The results indicate that the proposed algorithm exhibits high precision in speed and angle estimation, robust anti-disturbance capabilities, and excellent overall performance.

  • Open Access

    A Review of Simultaneous Localization and Mapping Algorithms Based on Lidar

    by Yong Li, Jiexin An, Na He, Yanbo Li, Zhenyu Han, Zishan Chen, Yaping Qu

    Simultaneous localization and mapping (SLAM) is one of the key technologies for mobile robots to achieve autonomous driving, and the lidar SLAM algorithm is the mainstream research scheme. Firstly, this paper introduces the overall framework of lidar SLAM, elaborates on the functions of front-end scan matching, loop closure detection, back-end optimization, and map building module, and summarizes the algorithms used. Then, the classical representative SLAM algorithms are described and compared from three aspects: pure lidar SLAM algorithm, multi-sensor fusion SLAM algorithm, and deep learning lidar SLAM algorithm. Finally, the challenges faced by the lidar SLAM algorithm in practical use are discussed. The development trend of the lidar SLAM algorithm is prospected from five dimensions: lightweight, multi-sensor fusion, combination of new sensors, multi-robot collaboration, and deep learning. This paper can provide a brief guide for novices entering the field of SLAM and provide a comprehensive reference for experienced researchers and engineers to explore new research directions.