MCMridusmita Roy Choudhury

Mridusmita Roy Choudhury

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mridusmita Roy Choudhury has a total of 40 co-authors. Here are the top co-authors by number of shared publications:

  • Kishore Debnath

    Department of Mechanical Engineering, National Institute of Technology Meghalaya, Sohra, Meghalaya, India

    7 shared publications
  • Hrishikesh Dutta

    Centre for Additive Manufacturing, Chennai Institute of Technology, Chennai, India

    4 shared publications
  • M Shanmuka Srinivas

    SASTRA Deemed Univ, Dept Mech Engn, Thanjavur, Tamil Nadu, India

    2 shared publications
  • Anil Borah

    Department of Mechanical Engineering, Assam Engineering College , Guwahati , 781013 Assam , India

    1 shared publication
  • Ankit Kumar R. Sharma

    Department of Mechanical Engineering, National Institute of Technology Meghalaya, Shillong, India

    1 shared publication
  • Ashwin Anantharamakrishnan Vimala

    Department of Mechanical Engineering, Chennai Institute of Technology, Chennai, India

    1 shared publication

Latest Publications

  • Open Access

    Predictive modelling and optimization of WEDM of nickel aluminium bronze alloy using optimised support vector regression and evolutionary algorithm

    by Subhankar Saha, Sri Srinivasa Raju Modampuri, Hrishikesh Dutta, Rammohan Mallipeddi, Dhanaraj Savary Nasan, Mridusmita Roy Choudhury

    The primary objective of this study was to develop an accurate predictive framework and an efficient multi-objective optimisation strategy for wire electric discharge machining (WEDM) of NAB alloy, focusing on Cutting Speed (CS) and Surface Roughness (SR). An optimized Support Vector Regression (OSVR) model was constructed to capture the complex and stochastic input–output relationships inherent to the spark erosion process. The model exhibited excellent predictive accuracy, with MSE = 0.0027 and R 2 = 0.9970 for CS and MSE = 0.0012 and R 2 = 0.9924 for SR, validated through scatter and stem plots. To optimise the conflicting objectives of maximising CS and minimising SR, an adaptive offspring generation-driven indicator-based evolutionary algorithm (IBEA-AOG) was applied. The algorithm generated 100 Pareto-optimal solutions and outperformed twelve state-of-the-art algorithms, as confirmed by Friedman mean rank and Nemenyi tests. Spearman correlation analysis was used to assess the influence of process parameters on CS and SR. Surface integrity was further evaluated using field emission scanning electron microscopy (FESEM) and non-contact optical profilometry. High discharge energy settings produced surfaces with globules, large melted deposits, and overlapping craters due to poor dielectric flushing, while low discharge energy led to smoother surfaces with fewer craters and thinner recast layers. Microcracks were observed under all conditions, but were more pronounced at higher energies owing to steeper thermal gradients. Overall, the OSVR-IBEA-AOG hybrid framework proved highly effective for prediction, analysis, and multi-objective optimisation in WEDM.


  • Open Access

    Process optimization in micro electrical discharge machining of carbon kevlar hybrid composite using TOPSIS

    by Hrishikesh Dutta, Kishore Debnath, Sargunan Karunanithi, Ashwin Anantharamakrishnan Vimala, Dhinakaran Veeman, Mridusmita Roy Choudhury

    This work is an experimental investigation and multi-response optimization of micro-electrical discharge machining (µEDM) of carbon-Kevlar hybrid composite (CKHC). Based on the chosen input factors namely voltage (V), EDM feed (EF) and tool speed (TS), the experimental runs were fixed as per Taguchi’s L9 orthogonal array. Single and multi-response optimization were carried out using Taguchi and technique for order of preference by similarity to ideal solution (TOPSIS). The responses selected for the study were machining time (MT) and degree of circularity (DOC). The Taguchi analysis identified the optimal input parameter values for minimal MT as a V of 180 volts, EF of 2 μm/sec, and TS of 1000 rpm. The corresponding values for the maximum DOC were 120 volts, 2 μm/sec, and 1000 rpm. Analysis of variance (ANOVA) revealed that voltage significantly affects the variation in MT. However, the DOC is mostly affected by the change in TS. The optimal values of V, EF, and TS obtained from TOPSIS were 150 volts, 4 μm/sec, and 1000 rpm. An improvement of 0.757881 in the preferred solution for optimal settings was confirmed from the analysis. Images from scanning electron microscopy (SEM) confirmed the overcut of the machined micro-holes.


  • Open Access

    Machine learning-based model to predict von Mises stress and chip reduction coefficient developed during dry turning of EN36C steel

    by Vishal Mishra, Nikhil Bharat, Kalyan Chakraborty, Vijay Kumar, Mridusmita Roy Choudhury

    This study comprehensively investigates the determination of chip reduction coefficient (CRC) and von Mises stress (VMS) during dry turning of Nickel-Chromium case-hardened steel (EN36C), renowned for its high surface hardness and core toughness. Machining parameters, including cutting speed (36–100 m/min), feed rate (0.49–0.86 mm/rev), and depth of cut (0.67–1.5 mm), were rigorously analyzed using Analysis of Variance (ANOVA) and Artificial Neural Networks. ANOVA identified cutting speed as the most influential factor, accounting for 52.04% of CRC and 35.04% of VMS variations, with feed rate and depth of cut also playing significant roles. ANN modeling achieved a correlation coefficient of 0.97, demonstrating excellent predictive accuracy for parameter optimization. Scanning Electron Microscopy revealed chip morphology, showing continuous chips under optimal conditions of high cutting speed (100 m/min), low feed rate (0.63 mm/rev), and moderate depth of cut (1.0 mm), minimizing stress and enhancing material removal efficiency. Brittle chips were observed at lower speeds (36 m/min) and higher feed rates, emphasizing the critical role of parameter selection. Optimal machining parameters significantly improved surface quality, reduced tool wear, and minimized operational stresses. This research offers a robust framework for machining process optimization, with implications for enhancing industrial efficiency and cost-effectiveness.


  • Open Access

    Influence of powdered bamboo filler content on the tensile strength and fatigue life of epoxy composites

    by Chaiki Malakar, Hrishikesh Dutta, Sumit Bhowmik, Ravivarman R, Mridusmita Roy Choudhury

    The aim of this study is to evaluate the influence of reinforcing powdered bamboo filler (PBF) on the mechanical and fatigue properties of epoxy-based polymer composites, with a focus on balancing void content and tensile strength. Epoxy composites were fabricated by incorporating varying content of PBF (2.5%, 5%, 7.5%, 10%, and 12.5% by weight) using casting process, at room temperature (32 °C–34 °C) for 24–48 h. The prepared samples were subjected to mechanical testing (tensile strength), fatigue analysis, void content evaluation, and microstructural examination to assess the effects of filler concentration. The specimen with 12.5% PBF exhibited the highest void content (7.75%), while the neat epoxy sample showed the lowest (3.24%). An increasing trend in tensile strength was observed with higher PBF content, peaking at 24.172 MPa for the 12.5% PBF composite. Fatigue resistance improved with filler content; notably, the composite with 10% PBF endured over 106 fatigue cycles. Microstructural analysis revealed noticeable agglomeration of PBF particles in samples with filler content above 10%. The results suggest that incorporating powdered bamboo filler into epoxy composites can significantly enhance mechanical and fatigue properties, particularly up to a 10% filler concentration. However, excessive filler loading (beyond 10%) may lead to particle agglomeration and increased void content, which could negatively impact performance. These findings provide valuable insights for optimizing natural filler content in sustainable composite material design. The noted enhancements in tensile strength and fatigue life indicate that these composites may be appropriate for lightweight structural applications, especially in non-load-bearing scenarios.


  • Optimizing aerodynamics: Numerical flow analysis for drag and lift reduction in SUV designs

    by Pritam Majumder, Mridusmita Roy Choudhury, Gunjan Karmaka, Pritam Baishya, Shweta Singh


  • Open Access

    Optimizing drilling parameters for fly ash-filled hemp/epoxy composites: investigating drill bit geometries, feed rates, and spindle speeds

    by Mridusmita Roy Choudhury, Hrishikesh Dutta, M Shanmuka Srinivas, Kishore Debnath, T Arunkumar, Vikas Upadhyay

    This article investigates the drilling behavior of hemp fiber-reinforced epoxy composites, both unfilled and fly ash-filled. Drilling performance tests were conducted at varying feed rates (8, 16, and 24 mm min−1) and spindle speeds (700, 1400, and 2100 RPM) using three drill geometries: parabolic, 8-facet, and dagger. The fly ash-filled hemp/epoxy composite showed significant reductions in maximum thrust force (25.09%, 19.92%, and 21.43%) and torque (80%, 79.87%, and 59.25%) when drilled with parabolic, 8-facet, and dagger drill bits, respectively, compared to the unfilled composite. The maximum drilling temperature reached 90.6 °C during cutting and decreased to 71.7 °C post-drilling. Overall, the fly ash-filled composites demonstrated superior performance in terms of drilling-induced stresses and damage.


  • Open Access

    Green lubricants in action: a comprehensive performance evaluation of groundnut oil-based cutting fluids in metal machining processes

    by M Shanmuka Srinivas, Dheeraj Kumar, P S Suvin, Satish V Kailas, Sanjay R Pawar, Mridusmita Roy Choudhury

    As industries worldwide seek environmentally sustainable solutions, the metalworking sector faces a growing need for eco-friendly alternatives to traditional cutting fluids. This abstract introduces the concept of an innovative approach to cutting fluid technology—the use of groundnut oil as a base material for machining fluids. Derived from peanuts, groundnut oil presents a renewable and biodegradable alternative to petroleum-based counterparts, addressing concerns related to resource depletion and environmental impact. A comprehensive performance evaluation of groundnut oil- based cutting fluid has been carried out by series of critical tests such as separation testing, particle size and stability testing, frictional testing, corrosion testing and drilling testing. The results of these tests collectively contribute to a comprehensive understanding of groundnut oil-based cutting fluids, shedding light on their potential as sustainable and high-performance alternatives in metalworking. The zeta potential for the prepared green cutting fluid has been found to be 49.10 mV. The dimensions of the dispersed particles in a fluid of the cutting fluid have been found as 250–260 nm. The environmentally friendly cutting fluid exhibits favourable outcomes in corrosion resistance, frictional performance, and drilling efficacy during testing.


  • Open Access

    Advancing Microchannel Fabrication: Tool‐Innovated Die Sink Electrodischarge Machining

    by M. Shanmuka Srinivas, R. Meenakshi Reddy, Praveen Kumar Balguri, Din Bandhu, Manas Das, Kishore Debnath, Mridusmita Roy Choudhury

    In the current fast‐changing technological fields, microchannels are playing a vital role by enhancing the field of thermal transfer efficiency. The research aims to explore innovative approaches within die sink electrodischarge machining (EDM) to enhance microchannel fabrication. In micro‐EDM, tool wear and unpredictable process parameter effects often hinder hole quality and productivity enhancement. The study delves into innovative tool designs, electrode materials, and process parameters aimed at enhancing both the efficiency and precision of microchannel creation. Stainless steel has long been celebrated for its exceptional corrosion resistance, durability, and versatility across a myriad of industrial applications. The novel tool design utilizes stainless‐steel (Grade 301) blades to fabricate microchannels through die sink EDM on SS301 stainless‐steel slabs. An investigation was conducted to explore the attributes of microchannels through the optimization of process parameters in die sink EDM. Control parameters such as sparking current, duty cycle, active pulse duration, and gap voltage were selected and studied to assess their impact on the depth and width of the channels. The comprehensive surface morphology of the machined characteristics was evaluated using scanning electron microscope (SEM) and noncontact interferometer images. This study demonstrates that enhancing the depth of the channel can be achieved by decreasing the duty cycle and active duration of the pulse, while increasing the sparking current and gap voltage. Moreover, reducing the duty cycle, active pulse duration, and gap voltage can diminish the overcut of the channel.


  • Open Access

    Optimization of process parameters in plasma arc cutting of commercial-grade aluminium plate

    by Mridusmita Roy Choudhury, Hrishikesh Dutta, Utpal Deka, Basireddy Bhavani, Kuldeep K. Saxena, Anil Borah

    Plasma arc cutting (PAC) has emerged as a versatile and efficient method for the precision cutting of various materials, including commercial-grade aluminium plates. The optimization of process parameters is crucial for achieving high-quality cuts, minimizing material wastage, and enhancing overall productivity. This study aims to systematically investigate and optimize the key process parameters in PAC of commercial-grade aluminium plates. The experimental design involves the manipulation of parameters such as arc current, gas pressure, and workpiece thickness. A Design of Experiments approach, specifically Taguchi’s orthogonal array, is employed to efficiently explore the parameter space and identify the optimal combination of settings. The response variables considered for optimization include minimum surface roughness, minimum burr height, and maximum material removal rate (MRR). Analysis of variance is performed to get the percentage influence of each process parameter on the performance characteristic. The results obtained from the optimization process are expected to provide valuable insights into enhancing the efficiency and precision of PAC for commercial-grade aluminium plates. Arc current is found to be the most significant parameter in altering the surface roughness. The thickness of the material is the most significant parameter in altering burr height. None of the parameters is found to be significant in altering the MRR from Analysis of Variance analysis. From signal-to-noise ratio analysis and average performance graph, the optimum combination of processes in altering the bur height and MRR are found as arc current at 50 amp, the gas pressure at 5.4 bar, and the thickness of the workpiece at 6 mm.


  • Analysis of hybrid joints of green composites under tensile and compressive loadings

    by Mridusmita Roy Choudhury, Kishore Debnath

    Adhesive bonding and mechanical fastening techniques are mostly applied for the joining of polymer composites. However, in recent times, the hybrid joining (bonded/bolted) technique is emerging, as it prevents premature failure of composite joints. An experimental investigation was carried out in this study to analyze the hybrid joining behavior of green composites (bamboo/poly(lactic acid) (PLA)) under tensile and compressive loadings. The hybrid joints were developed by combining bolted and bonded joints. The hole in the specimen prerequisite for the bolted joint was obtained by traditional drilling performed at a constant spindle speed of 2000 revolutions per min and an axial feed of 45 mm/min using a multifaceted solid carbide drill bit. A bolt fastening torque of 20 N m was applied to facilitate the mechanical joining. Three bonding materials – namely, (a) epoxy, (b) polyurethane and (c) parent polymer (PLA) – were used to obtain the bonded joint. The important factors of the hybrid joint, such as (a) overlapping length, (b) width of the specimen and (c) bonding material, were considered, and their effect on both tensile and compressive failure loads was evaluated. The significance of the parameters of the hybrid joint was evaluated through statistical modeling.