Ravinder Singh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ravinder Singh has a total of 82 co-authors. Here are the top co-authors by number of shared publications:
- Dominic C. O'Brien
Department of Engineering Science, University of Oxford, Oxford, U.K.
6 shared publications - Grahame Faulkner
Department of Engineering Science, University of Oxford, Oxford, U.K.
6 shared publications - Mauro Biagi
Sapienza University of Rome
5 shared publications - Timothy O Farrell
Department of Electronic and Electrical Engineering, University of Sheffield, Sheffield, U.K.
5 shared publications - Periklis Petropoulos
Optoelectronics Research Centre, University of Southampton, Southampton, UK
3 shared publications - Steve Collins
Department of Engineering Science, University of Oxford, Oxford, U.K.
3 shared publications
Latest Publications
- Open Access
- 8 June 2026
- Published by American Physical Society (APS) in Physical Review Research
- Vol. 8 (2)
Feasibility of multi-gigahertz satellite-to-ground secure quantum communication
We investigate the feasibility of satellite-to-ground quantum key distribution (QKD) at multi-GHz clock rates, where secure key generation time is constrained, due to low-Earth orbit (LEO) satellite overpasses ( ≈ 300 s). Higher repetition rates offer a direct route to increased secure key rate (SKR), though system performance is fundamentally limited by detector timing jitter, optical coupling losses, and atmospheric turbulence, depending on receiver architecture. We combine finite-key modeling, detailed detector timing characterization, adaptive optics (AO) modeling, and real-time free-space QKD experiments at 1 GHz to evaluate practical receiver configurations based on multi-mode fiber-coupled avalanche photodiodes (MMF-APDs) and single-mode fiber-coupled superconducting nanowire single-photon detectors (SMF-SNSPDs), at projected rates >1 GHz. The results indicate clear operating regimes across a range of atmospheric conditions: MMF-APDs maximize secure key rates below ∼ 1 GHz, mainly due to their low coupling loss. However, low-jitter SMF-SNSPDs are required to obtain positive key rates at higher clock rates—with modeling and measured timing responses of our hardware indicating an estimated optimal operating point near ∼ 7.2 GHz—though AO correction is required for effective single-mode coupling under turbulence. The experimental and projected results provide quantitative performance bounds and realistic design targets for future high-rate satellite QKD systems, while highlighting the technological requirements needed to achieve end-to-end operation beyond the GHz regime.
- 8 June 2026
- Published by American Physical Society (APS) in Physical Review Research
- Vol. 8 (2)
Open AccessFeasibility of multi-gigahertz satellite-to-ground secure quantum communication
We investigate the feasibility of satellite-to-ground quantum key distribution (QKD) at multi-GHz clock rates, where secure key generation time is constrained, due to low-Earth orbit (LEO) satellite overpasses ( ≈ 300 s). Higher repetition rates offer a direct route to increased secure key rate (SKR), though system performance is fundamentally limited by detector timing jitter, optical coupling losses, and atmospheric turbulence, depending on receiver architecture. We combine finite-key modeling, detailed detector timing characterization, adaptive optics (AO) modeling, and real-time free-space QKD experiments at 1 GHz to evaluate practical receiver configurations based on multi-mode fiber-coupled avalanche photodiodes (MMF-APDs) and single-mode fiber-coupled superconducting nanowire single-photon detectors (SMF-SNSPDs), at projected rates >1 GHz. The results indicate clear operating regimes across a range of atmospheric conditions: MMF-APDs maximize secure key rates below ∼ 1 GHz, mainly due to their low coupling loss. However, low-jitter SMF-SNSPDs are required to obtain positive key rates at higher clock rates—with modeling and measured timing responses of our hardware indicating an estimated optimal operating point near ∼ 7.2 GHz—though AO correction is required for effective single-mode coupling under turbulence. The experimental and projected results provide quantitative performance bounds and realistic design targets for future high-rate satellite QKD systems, while highlighting the technological requirements needed to achieve end-to-end operation beyond the GHz regime.
- Open Access
- 26 March 2024
- Published by IntechOpen
Indoor Laser-Based Wireless Communications
Optical wireless communication (OWC) is a strong candidate in the sixth generation (6G) of wireless communications as it can support data transmission at high communication speeds, low power consumption, high security, and high reliability. Near-infrared lasers, specifically vertical cavity surface emitting lasers (VCSELs), exhibit larger modulation bandwidth compared to light-emitting diodes (LEDs), and can provide aggregate data rates ranging up to Terabit per second (Tbps). This chapter proposes innovative optical transmitter and receiver designs for indoor laser-based wireless communications, aiming to provide seamless coverage in high-speed multi-user scenarios. The proposed optical transmitter is based on a 55 VCSEL array where each VCSEL can provide 10 Gigabit per second (Gbps) in a uniform coverage area of 20cm x 20cm, achieving a total of 250 Gbps in an area of 1at 3m transmission distance. Moreover, two wide-FOV receiver designs that employ photodetector (PD) arrays in along with imaging or non-imaging optics are introduced to support such an ultra-high-speed optical link. The new design of OWC requires potential techniques to address various networking challenges, including cell formation, interference management, resource allocation, and backhauling. To this end, potential solutions for these challenges are discussed to help establish an end-to-end OWC infrastructure for practical deployment. - 26 March 2024
- Published by IntechOpen
Open AccessIndoor Laser-Based Wireless Communications
Optical wireless communication (OWC) is a strong candidate in the sixth generation (6G) of wireless communications as it can support data transmission at high communication speeds, low power consumption, high security, and high reliability. Near-infrared lasers, specifically vertical cavity surface emitting lasers (VCSELs), exhibit larger modulation bandwidth compared to light-emitting diodes (LEDs), and can provide aggregate data rates ranging up to Terabit per second (Tbps). This chapter proposes innovative optical transmitter and receiver designs for indoor laser-based wireless communications, aiming to provide seamless coverage in high-speed multi-user scenarios. The proposed optical transmitter is based on a 55 VCSEL array where each VCSEL can provide 10 Gigabit per second (Gbps) in a uniform coverage area of 20cm x 20cm, achieving a total of 250 Gbps in an area of 1at 3m transmission distance. Moreover, two wide-FOV receiver designs that employ photodetector (PD) arrays in along with imaging or non-imaging optics are introduced to support such an ultra-high-speed optical link. The new design of OWC requires potential techniques to address various networking challenges, including cell formation, interference management, resource allocation, and backhauling. To this end, potential solutions for these challenges are discussed to help establish an end-to-end OWC infrastructure for practical deployment. - Open Access
- 1 December 2023
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 9 (48) , eadj5873
Real-time gigahertz free-space quantum key distribution within an emulated satellite overpass
Satellite quantum key distribution (SatQKD) intermediated by a trusted satellite in a low-Earth orbit to ground stations along the satellite’s path allows remote users to connect securely. To establish a secure connection, a SatQKD session must be conducted to each user over a dynamically changing free-space link, all within just a few hundred seconds. Because of the short time and large losses under which the QKD protocol will be implemented, it has not yet been possible to form a complete key by transmitting all the relevant information required within a single overpass of the satellite. Here, we demonstrate a real-time QKD system that is capable of forming a 4.58-megabit secure key between two nodes within an emulated satellite overpass. We anticipate that our system will set the stage for practical implementations of intercontinental quantum secure communications that can operate over large networks of nodes and enable the secure transmission of data globally.
- 1 December 2023
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 9 (48) , eadj5873
Open AccessReal-time gigahertz free-space quantum key distribution within an emulated satellite overpass
Satellite quantum key distribution (SatQKD) intermediated by a trusted satellite in a low-Earth orbit to ground stations along the satellite’s path allows remote users to connect securely. To establish a secure connection, a SatQKD session must be conducted to each user over a dynamically changing free-space link, all within just a few hundred seconds. Because of the short time and large losses under which the QKD protocol will be implemented, it has not yet been possible to form a complete key by transmitting all the relevant information required within a single overpass of the satellite. Here, we demonstrate a real-time QKD system that is capable of forming a 4.58-megabit secure key between two nodes within an emulated satellite overpass. We anticipate that our system will set the stage for practical implementations of intercontinental quantum secure communications that can operate over large networks of nodes and enable the secure transmission of data globally.
- 7 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 41 (17) , 5577-5587
Vector Coding Optical Wireless Links
The quasi-static nature of the optical wireless channel means that the channel state information (CSI) can be readily available at the transmitter and receiver prior to data transmission. This implies that electrically band-limited optical wireless communication (OWC) systems can make use of optimal channel partitioning or vector coding based multi-channel modulation (MCM) to achieve high throughput by mitigating the non-linearities arising from the optical and electrical channel. This paper proposes a pulse amplitude modulation (PAM) based DC-biased optical vector coding (DCO-VC) MCM scheme for OWC. The throughput performance of DCO-VC is evaluated and compared to the well known DC-biased optical orthogonal frequency division multiplexing (DCO-OFDM) over hybrid (line-of-sight and diffuse) and diffuse (non line-of-sight only) visible light communication (VLC) channels with additive white Gaussian noise. For the completeness of the VLC physical layer, the performance comparison is based on an uncoded and a forward error correction transmission mode using well-known convolutional codes with Viterbi decoder. The results show that the coded DCO-VC outperforms DCO-OFDM system by achieving up to 2 and 3 dB signal to noise ratio gains over hybrid and diffuse VLC channels, respectively.
- 7 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 41 (17) , 5577-5587
Vector Coding Optical Wireless Links
The quasi-static nature of the optical wireless channel means that the channel state information (CSI) can be readily available at the transmitter and receiver prior to data transmission. This implies that electrically band-limited optical wireless communication (OWC) systems can make use of optimal channel partitioning or vector coding based multi-channel modulation (MCM) to achieve high throughput by mitigating the non-linearities arising from the optical and electrical channel. This paper proposes a pulse amplitude modulation (PAM) based DC-biased optical vector coding (DCO-VC) MCM scheme for OWC. The throughput performance of DCO-VC is evaluated and compared to the well known DC-biased optical orthogonal frequency division multiplexing (DCO-OFDM) over hybrid (line-of-sight and diffuse) and diffuse (non line-of-sight only) visible light communication (VLC) channels with additive white Gaussian noise. For the completeness of the VLC physical layer, the performance comparison is based on an uncoded and a forward error correction transmission mode using well-known convolutional codes with Viterbi decoder. The results show that the coded DCO-VC outperforms DCO-OFDM system by achieving up to 2 and 3 dB signal to noise ratio gains over hybrid and diffuse VLC channels, respectively.
- 20 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 41 (16) , 5226-5232
Coexistence of Quantum and 1.6 Tbit/s Classical Data Over Fibre-Wireless-Fibre Terminals
In this article a fibre free-space fibre link that allows a quantum key distribution (QKD) signal and high-speed data to be transmitted in a single optical beam is presented. This setup has the potential to provide ultra-high data rate secure wireless connectivity within indoor spaces. Both quantum and classical channels were transmitted using wavelengths in the C band, over a range of 2.5 m in free space and in the presence of a 200 lx background illumination. Raman noise caused by the light propagating in the optical fibres which provide connections to the free-space segment, together with geometric loss of the free-space link are the major impairments. Results yield secret key rates of 2.343 kbit/s when the QKD signal is sent without high-speed data (and associated Raman noise), and rates of 1.305–1.996 kbit/s when high-speed data is also transmitted (depending on spectral separation of QKD and classical information). Further, it is shown that the secret key rate can be optimised by increasing loss to attenuate the Raman noise by misalignment of the link. Improvement of the secret key rate from 1.305 kbit/s to 1.887 kbit/s was shown using this method.
- 20 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 41 (16) , 5226-5232
Coexistence of Quantum and 1.6 Tbit/s Classical Data Over Fibre-Wireless-Fibre Terminals
In this article a fibre free-space fibre link that allows a quantum key distribution (QKD) signal and high-speed data to be transmitted in a single optical beam is presented. This setup has the potential to provide ultra-high data rate secure wireless connectivity within indoor spaces. Both quantum and classical channels were transmitted using wavelengths in the C band, over a range of 2.5 m in free space and in the presence of a 200 lx background illumination. Raman noise caused by the light propagating in the optical fibres which provide connections to the free-space segment, together with geometric loss of the free-space link are the major impairments. Results yield secret key rates of 2.343 kbit/s when the QKD signal is sent without high-speed data (and associated Raman noise), and rates of 1.305–1.996 kbit/s when high-speed data is also transmitted (depending on spectral separation of QKD and classical information). Further, it is shown that the secret key rate can be optimised by increasing loss to attenuate the Raman noise by misalignment of the link. Improvement of the secret key rate from 1.305 kbit/s to 1.887 kbit/s was shown using this method.
- 24 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 40 (22) , 7254-7264
Optimized Multi-Primary Modulation for Visible Light Communication
Multi-primary modulation scheme has the potential to provide robust visible light communication links and mitigate any color fluctuations by providing identical chromaticity modulation alphabets. This work describes constellation optimization technique for multi-primary modulation (MPM), which shows that using different power levels for the primary lights can lead to obtain the same color and, furthermore, enhance the Euclidean distances between data symbols in the multi-dimensional color space. The bit error rate performances of the optimized MPM and the original non-optimized MPM schemes are evaluated considering indoor optical wireless channel models with additive white Gaussian noise. The results show that the optimized MPM provides better spectral efficiency and outperforms the original non-optimized MPM scheme by achieving up to 3.5 dB Signal-to-noise ratio gain for the same spectral efficiency and, therefore, opens doors for implementation of robust visible light communication links exploiting multi-color light sources.
- 24 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 40 (22) , 7254-7264
Optimized Multi-Primary Modulation for Visible Light Communication
Multi-primary modulation scheme has the potential to provide robust visible light communication links and mitigate any color fluctuations by providing identical chromaticity modulation alphabets. This work describes constellation optimization technique for multi-primary modulation (MPM), which shows that using different power levels for the primary lights can lead to obtain the same color and, furthermore, enhance the Euclidean distances between data symbols in the multi-dimensional color space. The bit error rate performances of the optimized MPM and the original non-optimized MPM schemes are evaluated considering indoor optical wireless channel models with additive white Gaussian noise. The results show that the optimized MPM provides better spectral efficiency and outperforms the original non-optimized MPM scheme by achieving up to 3.5 dB Signal-to-noise ratio gain for the same spectral efficiency and, therefore, opens doors for implementation of robust visible light communication links exploiting multi-color light sources.
- 4 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 40 (4) , 961-967
A Digital Pre-Equalizer For Optical Wireless Links
The range of transmitters, detectors and other components that can be used in optical wireless links means that they can have a wide variety of frequency responses. Both pre- and post- equalization have been used in optical wireless systems to increase data rates. Pre-equalization has the advantage that noise impairments due to equalization can be minimised. However, the variety of pre-equalizer transfer functions, which can be easily created using analog circuits, is limited by the frequency responses of these circuits. Consequently, it may not be possible to equalize some optical wireless links with analog circuit-based pre-equalizers. In this paper a flexible digital pre-equalization scheme that can equalize complex frequency responses is described. The flexibility and the applicability of the scheme is also demonstrated using two example systems, including one that incorporates a fluorescent optical fiber to create a wide-field-of-view receiver for handheld devices. In particular, the bandwidths of the two example systems have been increased to over 500 MHz and to 350 MHz, resulting in at least a three-fold increase in data rate without any post-equalization. The authors believe that this is the first time such significant improvements in on-off-keying data rates have been demonstrated in systems with a relatively complex frequency response and a limited dynamic range.
- 4 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 40 (4) , 961-967
A Digital Pre-Equalizer For Optical Wireless Links
The range of transmitters, detectors and other components that can be used in optical wireless links means that they can have a wide variety of frequency responses. Both pre- and post- equalization have been used in optical wireless systems to increase data rates. Pre-equalization has the advantage that noise impairments due to equalization can be minimised. However, the variety of pre-equalizer transfer functions, which can be easily created using analog circuits, is limited by the frequency responses of these circuits. Consequently, it may not be possible to equalize some optical wireless links with analog circuit-based pre-equalizers. In this paper a flexible digital pre-equalization scheme that can equalize complex frequency responses is described. The flexibility and the applicability of the scheme is also demonstrated using two example systems, including one that incorporates a fluorescent optical fiber to create a wide-field-of-view receiver for handheld devices. In particular, the bandwidths of the two example systems have been increased to over 500 MHz and to 350 MHz, resulting in at least a three-fold increase in data rate without any post-equalization. The authors believe that this is the first time such significant improvements in on-off-keying data rates have been demonstrated in systems with a relatively complex frequency response and a limited dynamic range.
- Open Access
- 30 September 2021
- Published by Optica Publishing Group in Optics Express
- Vol. 29 (21) , 33694-33702
Demonstration of >1Tbit/s WDM OWC with wavelength-transparent beam tracking-and-steering capability
Beam tracking-and-steering is crucial for the operation of high-speed, narrow beam, optical wireless communication (OWC) systems. Using a system based on two sets of low-cost cameras for continuous beam tracking and a set of mirrors for steering, we demonstrate here a high-capacity (>1Tbit/s) ten-channel wavelength-division multiplexed (WDM) OWC system based on discrete multitone transmission. The results, which are achieved over a 3.5-m perpendicular distance and across a lateral coverage up to 1.8 m, constitute to the best of our knowledge, the highest aggregate OWC capacity at this coverage.
- 30 September 2021
- Published by Optica Publishing Group in Optics Express
- Vol. 29 (21) , 33694-33702
Open AccessDemonstration of >1Tbit/s WDM OWC with wavelength-transparent beam tracking-and-steering capability
Beam tracking-and-steering is crucial for the operation of high-speed, narrow beam, optical wireless communication (OWC) systems. Using a system based on two sets of low-cost cameras for continuous beam tracking and a set of mirrors for steering, we demonstrate here a high-capacity (>1Tbit/s) ten-channel wavelength-division multiplexed (WDM) OWC system based on discrete multitone transmission. The results, which are achieved over a 3.5-m perpendicular distance and across a lateral coverage up to 1.8 m, constitute to the best of our knowledge, the highest aggregate OWC capacity at this coverage.
- Open Access
- 9 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 112726-112732
Experimental Characterization of Turbo-Coded 20 Gbps Fiber-Wireless-Fiber Optical Links
Fiber-wireless-Fiber links require alignment between the transmitter and receiver to a high degree of precision (typically ~ 0.01° for a link of a few meters), and channel coding can be used for mitigating the link margin reduction caused by the limited precision of the beam-steering and tracking system. This paper reports results from an experimental study of the misalignment tolerance attained by channel coding. Explicitly, the received power penalties imposed by misalignment are characterized, and then forward error correction techniques are adopted for mitigating the performance degradation inflicted, which is quantified experimentally. Our results characterize trade-offs between coding rate, decoding complexity and the degree of misalignment. Overall, an improvement of the tolerance to misalignment up to ~50% was attained for coded links compared with the uncoded counterpart.
- 9 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 112726-112732
Open AccessExperimental Characterization of Turbo-Coded 20 Gbps Fiber-Wireless-Fiber Optical Links
Fiber-wireless-Fiber links require alignment between the transmitter and receiver to a high degree of precision (typically ~ 0.01° for a link of a few meters), and channel coding can be used for mitigating the link margin reduction caused by the limited precision of the beam-steering and tracking system. This paper reports results from an experimental study of the misalignment tolerance attained by channel coding. Explicitly, the received power penalties imposed by misalignment are characterized, and then forward error correction techniques are adopted for mitigating the performance degradation inflicted, which is quantified experimentally. Our results characterize trade-offs between coding rate, decoding complexity and the degree of misalignment. Overall, an improvement of the tolerance to misalignment up to ~50% was attained for coded links compared with the uncoded counterpart.
- 26 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 33 (16) , 912-915
Raised Cosine Pulse Shaping for Pre-equalized Optical Wireless Links
Their programmability means that digital pre-equalization techniques are more flexible than analog circuit equalizers. However, their performance depends on the number of samples per data symbol needed to accurately represent the pre-equalized time domain pulse. This requirement limits the maximum data rate that can be generated by a digital-to-analog converter (DAC). Another challenge when pre-equalizing the signal applied to a transmitter is the need to restrict the maximum voltage applied to the transmitter. Given these challenges, this paper demonstrates the benefits of constructing digitally pre-equalized On-Off Keying (OOK) symbols with raised cosine pulses. In addition, results are presented which show that each symbol can be represented with as few as 5 samples per bit. The performance of the proposed equalization method is investigated using an off-the-shelf LED-based optical wireless communication (OWC) link. Using equalization, the bandwidth of the link is increased by a factor of 10 to 100 MHz. Consequently, the data rate achievable with a 2 GSa/s DAC is 400 Mb/s.
- 26 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 33 (16) , 912-915
Raised Cosine Pulse Shaping for Pre-equalized Optical Wireless Links
Their programmability means that digital pre-equalization techniques are more flexible than analog circuit equalizers. However, their performance depends on the number of samples per data symbol needed to accurately represent the pre-equalized time domain pulse. This requirement limits the maximum data rate that can be generated by a digital-to-analog converter (DAC). Another challenge when pre-equalizing the signal applied to a transmitter is the need to restrict the maximum voltage applied to the transmitter. Given these challenges, this paper demonstrates the benefits of constructing digitally pre-equalized On-Off Keying (OOK) symbols with raised cosine pulses. In addition, results are presented which show that each symbol can be represented with as few as 5 samples per bit. The performance of the proposed equalization method is investigated using an off-the-shelf LED-based optical wireless communication (OWC) link. Using equalization, the bandwidth of the link is increased by a factor of 10 to 100 MHz. Consequently, the data rate achievable with a 2 GSa/s DAC is 400 Mb/s.