Jean Michel Sprauel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jean Michel Sprauel has a total of 105 co-authors. Here are the top co-authors by number of shared publications:
- Jean-Marc Linares
Aix Marseille University
20 shared publications H. Michaud
Ascometal CREAS
10 shared publications- Laurent Barrallier
Arts et Métiers ParisTech
4 shared publications Alain Lodini
LISM
3 shared publicationsEmmanuel Mermoz
EUROCOPTER, Aéroport Internationale Marseille Provence, 13725 Marignane, France
3 shared publicationsG. Maeder
Ecole Nationale Supérieure d’Artset Métiers
3 shared publications
Latest Publications
- 1 February 2014
- Published by Elsevier in Computational Materials Science
- Vol. 82, 178-190
Mathematical modeling of residual stresses and distortions induced by gas nitriding of 32CrMoV13 steel
- 1 February 2014
- Published by Elsevier in Computational Materials Science
- Vol. 82, 178-190
Mathematical modeling of residual stresses and distortions induced by gas nitriding of 32CrMoV13 steel
- 1 October 2013
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 213 (10) , 1661-1668
Improving tool wear and surface covering in polishing via toolpath optimization
- 1 October 2013
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 213 (10) , 1661-1668
Improving tool wear and surface covering in polishing via toolpath optimization
- 2 April 2013
- Published by EDP Sciences in Mechanics & Industry
- Vol. 14 (1) , 31-41
Stress optimization and study of the sensitivity to geometric variations of a spur gear tooth profile
- 2 April 2013
- Published by EDP Sciences in Mechanics & Industry
- Vol. 14 (1) , 31-41
Stress optimization and study of the sensitivity to geometric variations of a spur gear tooth profile
- 13 February 2013
- Published by Wiley
- p. 341-374
Uncertainties in Tolerance Analysis and Specification Checking
- 13 February 2013
- Published by Wiley
- p. 341-374
Uncertainties in Tolerance Analysis and Specification Checking
- 1 March 2012
- Published by World Scientific Pub Co Pte Ltd
- p. 74-81
USING STATISTICAL CONFIDENCE BOUNDARY OF A D.O.E. RESPONSE SURFACE TO ESTIMATE OPTIMAL FACTORS
- 1 March 2012
- Published by World Scientific Pub Co Pte Ltd
- p. 74-81
USING STATISTICAL CONFIDENCE BOUNDARY OF A D.O.E. RESPONSE SURFACE TO ESTIMATE OPTIMAL FACTORS
- 1 January 2012
- Published by Elsevier in CIRP Annals
- Vol. 61 (1) , 483-486
Optical measurement for the estimation of contact pressure and stress
- 1 January 2012
- Published by Elsevier in CIRP Annals
- Vol. 61 (1) , 483-486
Optical measurement for the estimation of contact pressure and stress
- 31 December 2011
- Published by Elsevier in CIRP Annals
- Vol. 60 (1) , 531-534
Increasing of surface quality in friction free-form surfaces of knee prosthesis
- 31 December 2011
- Published by Elsevier in CIRP Annals
- Vol. 60 (1) , 531-534
Increasing of surface quality in friction free-form surfaces of knee prosthesis
- 28 March 2011
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 681, 303-308
Approach by Simulation of Residual Stress Generated by Shot-Peening and Their Stability during Fatigue Cycling
ASCOMETAL produces alloy steels used for spring (leaf or coil), where the weak fatigue points are on the surface which is reinforced by shot-peening. So, the fatigue optimization with the steel grade needs a perfect knowledge of the material answer after shot-peening. For that reason, an analytical model has been developed where low cycle fatigue behaviour and all the usual process parameters are integrated (especially the impact position, and the covering-rate). Moreover, through a Monte-Carlos approach, the model permits to analyse the effect of scattering elements like impact speeds, ball sizes, or material fatigue behaviour. With this model several key process parameters have been analysed and validated with residual stress profiles evaluated by X-ray diffraction. So, for spring leaf, the effect of an applied load during shot-peening or shakedown during bending fatigue is described.
- 28 March 2011
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 681, 303-308
Approach by Simulation of Residual Stress Generated by Shot-Peening and Their Stability during Fatigue Cycling
ASCOMETAL produces alloy steels used for spring (leaf or coil), where the weak fatigue points are on the surface which is reinforced by shot-peening. So, the fatigue optimization with the steel grade needs a perfect knowledge of the material answer after shot-peening. For that reason, an analytical model has been developed where low cycle fatigue behaviour and all the usual process parameters are integrated (especially the impact position, and the covering-rate). Moreover, through a Monte-Carlos approach, the model permits to analyse the effect of scattering elements like impact speeds, ball sizes, or material fatigue behaviour. With this model several key process parameters have been analysed and validated with residual stress profiles evaluated by X-ray diffraction. So, for spring leaf, the effect of an applied load during shot-peening or shakedown during bending fatigue is described.
- 28 March 2011
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 681, 261-266
Analytical and Experimental Approach of Residual Stress on Deep-Rolled Crankshafts and Auto-Fretted Diesel Injection Rails. Effect on Fatigue Resistances in Service
The fatigue resistance of car components such as crankshafts or diesel injection rails is mainly related to fatigue at geometrical singularities. Its understanding requires the simulations of the different steps of the industrial process resulting in residual stresses generation and their evolutions in service. First concerning crankshaft fatigue damage, a complete analytical model of residual stresses generation and shakedown in fatigue is presented. Then a fatigue criterion is established and validated for this application. Finally, for the high pressure diesel injection rail, this approach can be generalized to the holes intersection singularities.
- 28 March 2011
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 681, 261-266
Analytical and Experimental Approach of Residual Stress on Deep-Rolled Crankshafts and Auto-Fretted Diesel Injection Rails. Effect on Fatigue Resistances in Service
The fatigue resistance of car components such as crankshafts or diesel injection rails is mainly related to fatigue at geometrical singularities. Its understanding requires the simulations of the different steps of the industrial process resulting in residual stresses generation and their evolutions in service. First concerning crankshaft fatigue damage, a complete analytical model of residual stresses generation and shakedown in fatigue is presented. Then a fatigue criterion is established and validated for this application. Finally, for the high pressure diesel injection rail, this approach can be generalized to the holes intersection singularities.
- 28 March 2011
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 681, 215-222
External Reference Samples for Residual Stress Analysis by X-Ray Diffraction
The GFAC (French Association for residual stress analysis) decided in 2007 to work on external reference samples for residual stress analysis by X-ray diffraction as defined in the XPA 09-285 and EN 15305-2009 standards. Seven materials are studied: ferritic steel, martensitic steel, aluminium alloy, titanium alloy, 2 types of Nickel-Chromium alloy and tungsten thin layers deposited on silicon wafers. The purpose of this external round robin campaign is threefold: (i) to give possibilities for each laboratory involved in the campaign test to obtain external reference samples for each material tested, (ii) to validate a common procedure for qualification of external samples and (iii) to commercialise validated external reference samples through the GFAC association. A common approach of X-Ray diffraction parameters, samples geometry and standard procedure has been chosen and adopted by each laboratory involved in these tests. No indication in terms of residual stress calculation method is given; the choice of the method (centroid, middle point, maximum of peak, fitting…) is the choice of the laboratory according to their X-ray diffraction set-ups, softwares and experience. Once all samples are analysed, values given by each laboratory are compared and analysed.
- 28 March 2011
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 681, 215-222
External Reference Samples for Residual Stress Analysis by X-Ray Diffraction
The GFAC (French Association for residual stress analysis) decided in 2007 to work on external reference samples for residual stress analysis by X-ray diffraction as defined in the XPA 09-285 and EN 15305-2009 standards. Seven materials are studied: ferritic steel, martensitic steel, aluminium alloy, titanium alloy, 2 types of Nickel-Chromium alloy and tungsten thin layers deposited on silicon wafers. The purpose of this external round robin campaign is threefold: (i) to give possibilities for each laboratory involved in the campaign test to obtain external reference samples for each material tested, (ii) to validate a common procedure for qualification of external samples and (iii) to commercialise validated external reference samples through the GFAC association. A common approach of X-Ray diffraction parameters, samples geometry and standard procedure has been chosen and adopted by each laboratory involved in these tests. No indication in terms of residual stress calculation method is given; the choice of the method (centroid, middle point, maximum of peak, fitting…) is the choice of the laboratory according to their X-ray diffraction set-ups, softwares and experience. Once all samples are analysed, values given by each laboratory are compared and analysed.