Teimuraz Mchedlidze
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Teimuraz Mchedlidze has a total of 173 co-authors. Here are the top co-authors by number of shared publications:
M. Kittler
Joint Lab IHP/BTU 1 , Konrad-Wachsmann-Allee 1, D-03046 Cottbus, Germany
22 shared publicationsMartin Kittler
Jointlab IHP/BTU; Konrad-Wachsmann-Allee 1; 03046 Cottbus Germany
21 shared publicationsT. Arguirov
Joint Lab IHP/BTU, Konrad‐Wachsmann‐Allee 1, 03046 Cottbus, Germany, and IHP Microelectronics, Im Technologiepark 25, 15236 Frankfurt (Oder), Germany
19 shared publicationsTzanimir Arguirov
IHP microelectronics
15 shared publicationsM. Suezawa
Tohoku University Institute for Materials Research 980-8577 Sendai, Japan
14 shared publicationsManfred Reiche
Max-Planck-Institut für Mikrostrukturphysik, Weinberg 2, 06120 Halle, Germany
10 shared publications
Latest Publications
- Open Access
- 24 November 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (47) , 475107
Investigation of defects in 3C-SiC using deep level transient spectroscopy
In this work, epilayers of n -3C-SiC on Si were investigated using deep level transient spectroscopy (DLTS). The layer structure allowed the investigation of electrically active defects in the n type region of 3C-SiC. By comparison with theoretical calculations based on density functional theory supercells in combination with local moment counter charge from the literature, the observed DLTS peaks could be assigned to intrinsic defects, more specifically different clusters of vacancies and silicon interstitials. The defects may be formed due to the different lattice constants of 3C-SiC and Si, similarly to the dislocations and voids previously observed in TEM studies. Our studies suggest that the DLTS peak observed close to 260 K originates from overlapping two intrinsic defects containing a single positively charged carbon vacancy and a single positively charged silicon interstitial.
- 24 November 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (47) , 475107
Open AccessInvestigation of defects in 3C-SiC using deep level transient spectroscopy
In this work, epilayers of n -3C-SiC on Si were investigated using deep level transient spectroscopy (DLTS). The layer structure allowed the investigation of electrically active defects in the n type region of 3C-SiC. By comparison with theoretical calculations based on density functional theory supercells in combination with local moment counter charge from the literature, the observed DLTS peaks could be assigned to intrinsic defects, more specifically different clusters of vacancies and silicon interstitials. The defects may be formed due to the different lattice constants of 3C-SiC and Si, similarly to the dislocations and voids previously observed in TEM studies. Our studies suggest that the DLTS peak observed close to 260 K originates from overlapping two intrinsic defects containing a single positively charged carbon vacancy and a single positively charged silicon interstitial.
- Open Access
- 3 April 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (19)
On‐Stage Degradation of Solar Cells Studied Using Capacitance Transient and Luminescence Spectroscopies
The light‐ and temperature‐induced degradation (LeTID) of Si‐based solar cells remains one of their common stability issues. The degradation process and affecting factors are still widely discussed. Low‐temperature photo‐ and electroluminescence and deep‐level transient spectroscopy (DLTS) are rarely used in the LeTID studies. The methods can explore only small‐area samples extracted from the cells. A comparison of the fabricated cells in initial, degraded, and regenerated states by these methods is effective only if used for the same location of the cell. The mesa‐diodes fabricated from various locations of passivated emitter and rear contact (PERC) PV cells are mounted on the stages of PL/EL and DLTS setups for the initial state characterization. Subsequently, the diodes are subjected to degradation and regeneration treatments under constant bias, and each state is similarly characterized. All processes and tests are carried out on‐stage, that is, without moving a diode from the stage. Based on the newly obtained and previously reported results, it is suggested that LeTID reflects hydrogen dynamics between extended defects present in solar cells and hydrogen‐containing intrinsic defects formed during/after the contact firing process.
- 3 April 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (19)
Open AccessOn‐Stage Degradation of Solar Cells Studied Using Capacitance Transient and Luminescence Spectroscopies
The light‐ and temperature‐induced degradation (LeTID) of Si‐based solar cells remains one of their common stability issues. The degradation process and affecting factors are still widely discussed. Low‐temperature photo‐ and electroluminescence and deep‐level transient spectroscopy (DLTS) are rarely used in the LeTID studies. The methods can explore only small‐area samples extracted from the cells. A comparison of the fabricated cells in initial, degraded, and regenerated states by these methods is effective only if used for the same location of the cell. The mesa‐diodes fabricated from various locations of passivated emitter and rear contact (PERC) PV cells are mounted on the stages of PL/EL and DLTS setups for the initial state characterization. Subsequently, the diodes are subjected to degradation and regeneration treatments under constant bias, and each state is similarly characterized. All processes and tests are carried out on‐stage, that is, without moving a diode from the stage. Based on the newly obtained and previously reported results, it is suggested that LeTID reflects hydrogen dynamics between extended defects present in solar cells and hydrogen‐containing intrinsic defects formed during/after the contact firing process.
- Open Access
- 29 May 2022
- Published by Wiley in Physica Status Solidi (a)
- Vol. 219 (17)
Characterization of Ultrathin FDSOI Stacks Using Low‐Field Mobility
Herein, a method for the electrical characterization of a fully depleted silicon‐on‐insulator (FDSOI) high‐k dielectric‐metal‐gate stack is proposed. The method is based on assessing low‐field mobility in FDSOI field‐effect transistor (FET) from current–voltage measurements at various temperatures in the gate voltage range up to strong inversion. In addition to assessing the value of the low‐field mobility for the stack itself, it allows specifying the impact of various carrier‐scattering mechanisms on the total stack mobility. Further, the application of double‐gate operation in the optimal coupling mode for the FET allows analysis of the impact of the gate interfaces on mobility. The method can be used in the monitoring of stack quality and in the design and development of stack fabrication processes.
- 29 May 2022
- Published by Wiley in Physica Status Solidi (a)
- Vol. 219 (17)
Open AccessCharacterization of Ultrathin FDSOI Stacks Using Low‐Field Mobility
Herein, a method for the electrical characterization of a fully depleted silicon‐on‐insulator (FDSOI) high‐k dielectric‐metal‐gate stack is proposed. The method is based on assessing low‐field mobility in FDSOI field‐effect transistor (FET) from current–voltage measurements at various temperatures in the gate voltage range up to strong inversion. In addition to assessing the value of the low‐field mobility for the stack itself, it allows specifying the impact of various carrier‐scattering mechanisms on the total stack mobility. Further, the application of double‐gate operation in the optimal coupling mode for the FET allows analysis of the impact of the gate interfaces on mobility. The method can be used in the monitoring of stack quality and in the design and development of stack fabrication processes.
- Open Access
- 6 November 2020
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (24)
Characterization of Ultrathin Fully Depleted Silicon‐on‐Insulator Devices Using Subthreshold Slope Method
The subthreshold current–voltage (subthreshold slope) characteristic of a fully depleted silicon‐on‐insulator high‐k dielectric‐metal gate field‐effect transistor is applied for evaluation of the interface traps located at both the front and back channels. The proposed characterization method allows an estimation of averaged trap densities separately for the front and back interfaces of the channel. Performing subthreshold slope measurements at several temperatures allows the extraction of the energy distributions of the interface trap densities for both interfaces and obtaining essential characteristics of the stack.
- 6 November 2020
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (24)
Open AccessCharacterization of Ultrathin Fully Depleted Silicon‐on‐Insulator Devices Using Subthreshold Slope Method
The subthreshold current–voltage (subthreshold slope) characteristic of a fully depleted silicon‐on‐insulator high‐k dielectric‐metal gate field‐effect transistor is applied for evaluation of the interface traps located at both the front and back channels. The proposed characterization method allows an estimation of averaged trap densities separately for the front and back interfaces of the channel. Performing subthreshold slope measurements at several temperatures allows the extraction of the energy distributions of the interface trap densities for both interfaces and obtaining essential characteristics of the stack.
- Open Access
- 11 September 2019
- Published by Wiley in Physica Status Solidi (a)
- Vol. 216 (17)
In Situ Observation of the Degradation in Multi‐Crystalline Si Solar Cells by Electroluminescence
- 11 September 2019
- Published by Wiley in Physica Status Solidi (a)
- Vol. 216 (17)
Open AccessIn Situ Observation of the Degradation in Multi‐Crystalline Si Solar Cells by Electroluminescence
- 4 June 2019
- Published by Wiley in Physica Status Solidi (a)
- Vol. 216 (17)
Location and Properties of Carrier Traps in mc‐Si Solar Cells Subjected to Degradation at Elevated Temperatures
Multi‐crystalline Si (mc‐Si) solar cells subjected to carrier‐induced efficiency degradation at elevated temperatures are studied using deep‐level transient spectroscopy (DLTS), capacitance‐voltage, and electroluminescence (EL) measurements. Commercially available passivated emitter and rear cell (PERC) mc‐Si solar cells are investigated after short annealing in the dark (at T = 200 °C for 20 min), after degradation by a constant forward current at 70 °C, and after regeneration annealing at 200 °C for 20 min. The degradation is detected in situ by EL imaging of the surface of the cell. Several n+p mesa‐diodes, selectively fabricated on the front surface of the solar cell, allow the characterization of locations with various levels of degradation and density of extended defects. The degree of the degradation correlates with the local active boron concentration. At all stages, traps associated with extended defects (i.e., dislocations, grain boundaries, precipitates, etc.) are detected by DLTS, and these traps are not affected by changes in the degree of degradation. Two minority‐carrier traps with energy level positions in the bandgap at Ec −0.19 eV and Ec −0.34 eV are detected only in the degraded solar cells in concentrations that correlate with the local degree of cell degradation.
- 4 June 2019
- Published by Wiley in Physica Status Solidi (a)
- Vol. 216 (17)
Location and Properties of Carrier Traps in mc‐Si Solar Cells Subjected to Degradation at Elevated Temperatures
Multi‐crystalline Si (mc‐Si) solar cells subjected to carrier‐induced efficiency degradation at elevated temperatures are studied using deep‐level transient spectroscopy (DLTS), capacitance‐voltage, and electroluminescence (EL) measurements. Commercially available passivated emitter and rear cell (PERC) mc‐Si solar cells are investigated after short annealing in the dark (at T = 200 °C for 20 min), after degradation by a constant forward current at 70 °C, and after regeneration annealing at 200 °C for 20 min. The degradation is detected in situ by EL imaging of the surface of the cell. Several n+p mesa‐diodes, selectively fabricated on the front surface of the solar cell, allow the characterization of locations with various levels of degradation and density of extended defects. The degree of the degradation correlates with the local active boron concentration. At all stages, traps associated with extended defects (i.e., dislocations, grain boundaries, precipitates, etc.) are detected by DLTS, and these traps are not affected by changes in the degree of degradation. Two minority‐carrier traps with energy level positions in the bandgap at Ec −0.19 eV and Ec −0.34 eV are detected only in the degraded solar cells in concentrations that correlate with the local degree of cell degradation.
- 27 March 2019
- Published by Wiley in Physica Status Solidi (a)
- Vol. 216 (17)
In Situ Observation of the Degradation in Multi‐Crystalline Si Solar Cells by Electroluminescence
Carrier‐induced efficiency degradation of multi‐crystalline Si (mc‐Si) solar cells is studied in situ by detecting the electroluminescence (EL) from the cells. Series of spatially resolved EL images of the cells during constant forward current operation at low (24 °C) and at elevated (70 °C) temperatures are recorded. The degradation induced changes in the open circuit voltage correlate well with changes in the EL intensities. The similarity of light‐induced and carrier‐induced degradation processes for mc‐Si cells is confirmed. The correlation of the degradation with the material structure is analyzed. The degradation appears to correlate with the density of structural defects in the cells. The results verify that EL images present a powerful tool for in situ analyses of mc‐Si cell degradation processes in various cell structures with a broad variety of biasing and temperature conditions.
- 27 March 2019
- Published by Wiley in Physica Status Solidi (a)
- Vol. 216 (17)
In Situ Observation of the Degradation in Multi‐Crystalline Si Solar Cells by Electroluminescence
Carrier‐induced efficiency degradation of multi‐crystalline Si (mc‐Si) solar cells is studied in situ by detecting the electroluminescence (EL) from the cells. Series of spatially resolved EL images of the cells during constant forward current operation at low (24 °C) and at elevated (70 °C) temperatures are recorded. The degradation induced changes in the open circuit voltage correlate well with changes in the EL intensities. The similarity of light‐induced and carrier‐induced degradation processes for mc‐Si cells is confirmed. The correlation of the degradation with the material structure is analyzed. The degradation appears to correlate with the density of structural defects in the cells. The results verify that EL images present a powerful tool for in situ analyses of mc‐Si cell degradation processes in various cell structures with a broad variety of biasing and temperature conditions.
- 26 May 2017
- Published by Wiley in Physica Status Solidi (a)
- Vol. 214 (7)
Deep carrier traps in as grown isotopically pure 28Si FZ crystal
We studied a distribution of dopants and carrier traps in the FZ grown 28Si crystal. Samples cut‐out from various parts of an as‐grown crystal were analysed by deep level transient spectroscopy (DLTS) and photoluminescence (PL). Several traps were detected at the concentration level of ∼1010 cm−3 by DLTS. Careful analyses of the obtained signals allow attributing the related traps to agglomerates of intrinsic defects. A correlation of the trap concentration to the phosphorus doping, detected by PL and confirmed by electric measurements was also observed. A possible attribution of the traps to the previously reported defects will be discussed.
- 26 May 2017
- Published by Wiley in Physica Status Solidi (a)
- Vol. 214 (7)
Deep carrier traps in as grown isotopically pure 28Si FZ crystal
We studied a distribution of dopants and carrier traps in the FZ grown 28Si crystal. Samples cut‐out from various parts of an as‐grown crystal were analysed by deep level transient spectroscopy (DLTS) and photoluminescence (PL). Several traps were detected at the concentration level of ∼1010 cm−3 by DLTS. Careful analyses of the obtained signals allow attributing the related traps to agglomerates of intrinsic defects. A correlation of the trap concentration to the phosphorus doping, detected by PL and confirmed by electric measurements was also observed. A possible attribution of the traps to the previously reported defects will be discussed.
- 23 May 2017
- Published by Wiley in Physica Status Solidi (a)
- Vol. 214 (7)
Interface traps in 28 nm node field effect transistors detected by capacitance transient spectroscopy
The energy distribution of the interface trap density for high‐k metal gate field effect transistors, fabricated in the standard 28 nm node technology and subjected to various fabrication processes was obtained using the capacitance transient spectroscopy (CTS) method. The CTS results show a nice correspondence with those obtained by the characterization methods routinely used in semiconductor industry, but contain more information. Strong influence of the infrared illumination on the results of the CTS measurements was detected at temperatures T < 200 K. Therefore, a proper shielding from infrared irradiation is required during transient spectroscopy measurements at low temperatures.
- 23 May 2017
- Published by Wiley in Physica Status Solidi (a)
- Vol. 214 (7)
Interface traps in 28 nm node field effect transistors detected by capacitance transient spectroscopy
The energy distribution of the interface trap density for high‐k metal gate field effect transistors, fabricated in the standard 28 nm node technology and subjected to various fabrication processes was obtained using the capacitance transient spectroscopy (CTS) method. The CTS results show a nice correspondence with those obtained by the characterization methods routinely used in semiconductor industry, but contain more information. Strong influence of the infrared illumination on the results of the CTS measurements was detected at temperatures T < 200 K. Therefore, a proper shielding from infrared irradiation is required during transient spectroscopy measurements at low temperatures.
- 27 March 2017
- Published by AIP Publishing in Applied Physics Letters
- Vol. 110 (13)
Photoconductivity as a method to probe defects in ultra thin Si films
Silicon-on-insulator wafers with thicknesses of a boron doped p-type device layer 1.5 μm to 88 nm are probed by means of photoconductive spectroscopy. It is shown that the boron acceptor manifests itself as Fano resonances at 669 and 693 cm–1 associated with the excited states due to the spin-orbit split-off valence band as well as Γ-phonon replicas of intrinsic boron transitions associated with the states of the top of the valence band. More importantly, electrically neutral oxygen-related defects including interstitial oxygen also appear in the photoconductivity spectra as dips at the frequencies of the corresponding local vibrational modes. These findings demonstrate selectivity and high sensitivity of photoconductive spectroscopy, which make it a preferential technique to probe semiconductor thin films.
- 27 March 2017
- Published by AIP Publishing in Applied Physics Letters
- Vol. 110 (13)
Photoconductivity as a method to probe defects in ultra thin Si films
Silicon-on-insulator wafers with thicknesses of a boron doped p-type device layer 1.5 μm to 88 nm are probed by means of photoconductive spectroscopy. It is shown that the boron acceptor manifests itself as Fano resonances at 669 and 693 cm–1 associated with the excited states due to the spin-orbit split-off valence band as well as Γ-phonon replicas of intrinsic boron transitions associated with the states of the top of the valence band. More importantly, electrically neutral oxygen-related defects including interstitial oxygen also appear in the photoconductivity spectra as dips at the frequencies of the corresponding local vibrational modes. These findings demonstrate selectivity and high sensitivity of photoconductive spectroscopy, which make it a preferential technique to probe semiconductor thin films.