Jan Kubosek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jan Kubosek has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Oldrich Sucharda
Department of Building Materials and Diagnostics of Structures, Faculty of Civil Engineering, VSB-Technical University of Ostrava, Ludvíka Podéště 1875/17, 70800 Ostrava-Poruba, Czech Republic
5 shared publications - Jana Vaskova
VŚB-Technical University of Ostrava
2 shared publications Martina Smirakova
VŚB-Technical University of Ostrava
2 shared publications- Radim Čajka
Department of Structures, Faculty of Civil Engineering, VSB-Technical University of Ostrava, 708 00 Ostrava-Poruba, Czech Republic
2 shared publications - Jakub Vaskova1 shared publication
Pavlina Mateckova
VSB — Technical University of Ostrava
1 shared publication
Latest Publications
- Open Access
- 29 May 2018
- Published by Springer Nature in International Journal of Concrete Structures and Materials
- Vol. 12 (1) , 36
Punching Shear Failure of Concrete Ground Supported Slab
- 29 May 2018
- Published by Springer Nature in International Journal of Concrete Structures and Materials
- Vol. 12 (1) , 36
Open AccessPunching Shear Failure of Concrete Ground Supported Slab
- 14 June 2017
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 738, 185-194
Design of Bitumen Asphalt Belt Sliding Joint Based on Experiment Results
Foundation structures are usually exposed to dominant vertical load. However, in some cases there is also significant value of horizontal load caused e.g. by horizontal terrain deformation on areas attached with underground mining or by horizontal deformation of foundation structure due to pre-stressing, creep, shrinkage, and temperature variation. Through the friction between subsoil and foundations, the foundation structure must resist significant normal forces. The idea of sliding joints between subsoil and foundation structure, which eliminates the friction in footing bottom, comes from the 1970’s. The bitumen asphalt belt given rheological properties has been proven as an effective material for sliding joints. In the paper there are test results of shear resistance of currently used asphalt belts. The test results are used for subsoil shear stress analysis in model example of strip foundation. Shear resistance is calculated according to Czech code for designing buildings on undermined area and also using advanced FEM analysis.
- 14 June 2017
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 738, 185-194
Design of Bitumen Asphalt Belt Sliding Joint Based on Experiment Results
Foundation structures are usually exposed to dominant vertical load. However, in some cases there is also significant value of horizontal load caused e.g. by horizontal terrain deformation on areas attached with underground mining or by horizontal deformation of foundation structure due to pre-stressing, creep, shrinkage, and temperature variation. Through the friction between subsoil and foundations, the foundation structure must resist significant normal forces. The idea of sliding joints between subsoil and foundation structure, which eliminates the friction in footing bottom, comes from the 1970’s. The bitumen asphalt belt given rheological properties has been proven as an effective material for sliding joints. In the paper there are test results of shear resistance of currently used asphalt belts. The test results are used for subsoil shear stress analysis in model example of strip foundation. Shear resistance is calculated according to Czech code for designing buildings on undermined area and also using advanced FEM analysis.
- 14 June 2017
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 738, 140-150
Determination of Material Parameters for Nonlinear Analysis of Reinforced Concrete
The aim of the paper is a nonlinear analysis of concrete structures. For these type of tasks is an important suitable choice of model input parameters and concrete. Especially if the analysis is preceding the results of an experiment, which can determine the exact properties of concrete. The following properties of concrete are needed for nonlinear analysis: tensile strength and compressive strength of concrete. There are more procedures how to determine some unknown input parameters. The paper presents some approaches to calculating and selecting parameters, which are based primarily on the recommendations of the Model Code and professional articles. Specifically, the numerical analysis performed in our developed program which allows observing a nonlinear behaviour of concrete at loading case.
- 14 June 2017
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 738, 140-150
Determination of Material Parameters for Nonlinear Analysis of Reinforced Concrete
The aim of the paper is a nonlinear analysis of concrete structures. For these type of tasks is an important suitable choice of model input parameters and concrete. Especially if the analysis is preceding the results of an experiment, which can determine the exact properties of concrete. The following properties of concrete are needed for nonlinear analysis: tensile strength and compressive strength of concrete. There are more procedures how to determine some unknown input parameters. The paper presents some approaches to calculating and selecting parameters, which are based primarily on the recommendations of the Model Code and professional articles. Specifically, the numerical analysis performed in our developed program which allows observing a nonlinear behaviour of concrete at loading case.
- 1 September 2015
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 662, 81-84
Modelling and Analysis of Reinforced Concrete Beams
The goal of the paper is to model and evaluate the total load capacity of the reinforced concrete beams. A non-linear analysis and finite element method were used for that purpose. The model consists of 3D finite elements. The constitutive model of concrete for the non-linear analysis is based on a fracture-plastic theory. The input parameters are the data obtained in previous tests which included both standard tests and additional tests of the testing bodies. There is no shear reinforcement in the beams. The non-linear calculations were carried out for several variants. The study takes into considerations the influence of concrete properties as well as the size of the finite elements.
- 1 September 2015
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 662, 81-84
Modelling and Analysis of Reinforced Concrete Beams
The goal of the paper is to model and evaluate the total load capacity of the reinforced concrete beams. A non-linear analysis and finite element method were used for that purpose. The model consists of 3D finite elements. The constitutive model of concrete for the non-linear analysis is based on a fracture-plastic theory. The input parameters are the data obtained in previous tests which included both standard tests and additional tests of the testing bodies. There is no shear reinforcement in the beams. The non-linear calculations were carried out for several variants. The study takes into considerations the influence of concrete properties as well as the size of the finite elements.
- 6 August 2015
- Published by Civil-Comp, Ltd.
- Vol. 108
The Elastic-Plastic Calculation of Structural Details in Rolled Beams
- 6 August 2015
- Published by Civil-Comp, Ltd.
- Vol. 108
The Elastic-Plastic Calculation of Structural Details in Rolled Beams
- Open Access
- 1 January 2015
- Published by Elsevier in Procedia Engineering
- Vol. 109, 234-239
Finite Element Modelling and Identification of the Material Properties of Fibre Concrete
- 1 January 2015
- Published by Elsevier in Procedia Engineering
- Vol. 109, 234-239
Open AccessFinite Element Modelling and Identification of the Material Properties of Fibre Concrete
- 24 June 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 969, 73-77
Comparation of Numerical Methods for Calculation of Thin Slabs
The purpose of this paper is to compare calculation of internal forces and deformations of slabs for two calculation methods: the finite element method and the finite difference method. Two concrete slabs have been analysed. In the case of the finite element method, different element mesh are used, providing, thus, solutions in different variants. The calculation and algorithms is based on a thin slab theory. Variants calculate in program Scia Engineer effects of shearing forces by means of the Midlins theory or thin slab theory. Algorithms for the calculation were developed in Matlab.
- 24 June 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 969, 73-77
Comparation of Numerical Methods for Calculation of Thin Slabs
The purpose of this paper is to compare calculation of internal forces and deformations of slabs for two calculation methods: the finite element method and the finite difference method. Two concrete slabs have been analysed. In the case of the finite element method, different element mesh are used, providing, thus, solutions in different variants. The calculation and algorithms is based on a thin slab theory. Variants calculate in program Scia Engineer effects of shearing forces by means of the Midlins theory or thin slab theory. Algorithms for the calculation were developed in Matlab.