HLHo-Young Lee

Ho-Young Lee

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ho-Young Lee has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Finite Element Analysis and Electrohydrodynamic Multiphysics Modeling of a Corona-Streamer Discharge in a Two-Phase Flow Medium

    by Myung-Ki Baek, Ho-Young Lee

    This study proposes an electrohydrodynamic multiphysics modeling and finite element analysis technique to accurately simulate corona-streamer discharges in a two-phase flow medium. The discharge phenomenon is modeled as a multiphysics system, coupling the Poisson equation for the electric field with a charge dynamics model based on fluid methods and a thermofluid field for temperature effects. To optimize the numerical simulation, the tip-flat plate electrode model was simplified to two-dimensional axisymmetry, and an unordered lattice network was used to reduce computational time while maintaining high resolution in the region of interest. A high DC voltage was applied to the model to generate a local non-uniform electric field exceeding 10 MV/m, allowing the numerical simulations of ionization, recombination, and charge attachment in the streamer channel. The numerical results were compared with voltage and current measurements from full-scale experiments under identical geometry and initial conditions to verify the effectiveness of the proposed method. The results of this study enhance the understanding of the multiphysical mechanisms behind electrical discharge phenomena and can enable the prediction of insulation failure through simple simulations, eliminating insulation experiments on devices.


  • Analysis of Fire Propagation in Electrical Cable Trays Using the FLASH-CAT Model

    by Hyun-Min Kang, Jaiho Lee, Young-Seob Moon, Ho-Young Lee

    In this study, a novel fire modeling procedure was proposed for the computational fluid dynamics (CFD) simulation of electrical cable tray fires for improving fire safety in nuclear power plants. The simulation conditions were selected from cable fire experiments that were conducted in open atmosphere and enclosed compartment conditions, as part of the PRISME-3 (French acronym for “Fire Propagation in Elementary Multi-Room Scenarios”) project, an international cooperative project that was carried out under the auspices of the Nuclear Energy Agency (NEA) of OECD. To solve the CFD problem of heat and smoke flow caused by electrical cable fire, we used fire dynamics simulator (FDS) model based on the Naver–Stoke’s equation, which is suitable for low-speed heat flow. In the FDS model, the heat release rate per unit area (HRRPUA), fire duration, and physical properties of the cable were considered as main input parameters and boundary conditions to perform the cable fire simulation analysis. The HRRPUA time curve for cable fires was assumed to be the FLASH-CAT model presented in NUREG-7010. To validate FDS model with the experimental results of cable tray fire scenarios, we compared simulation results by different cable fire models to find a cable fire model that is consistent with the experimental results.


  • Open Access

    Analysis of variable inductor employing vegetable-based transformer oil with magnetic nanoparticles

    by Ho-Young Lee, Seung-Geon Hong, Myung-Ki Baek

    Variable inductors using magnetorheological fluids have recently been successfully applied to power-conversion devices; however, the thermal properties of Vegetable oil-based Magnetic Nanofluids (VMNFs) have not been investigated. In this study, the temperature characteristics of a variable inductor embedded with a VMNF were analyzed by developing a multiphysics analysis method and verified experimentally. To analyze the temperature distribution efficiently, a coupled analysis of the Magnetoquasistatic (MQS) field and steady-state heat transfer field based on the finite-element method was performed. The B-H curves of the VMNF and ferrite core were obtained via magnetic property measurement experiments, and the input waveforms were measured from the current and high-frequency pulse voltages applied to the variable inductor of the DC–DC converter. To predict the temperature rise of the VMNF-gap variable inductor, the power dissipation was determined using the Steinmetz experimental equation modified by the Bertotti model in the electronic system solver and input as a heat source in the steady-state heat-transfer analysis. The temperature increase predicted by the multiphysics analysis method agreed well with the experimental data, and an increasing the concentration of magnetic nanoparticles had a cooling effect. The developed MQS–thermal field coupled analytical method and the cooling properties of VMNFs can be applied to the design of power-conversion devices operating with high-frequency power sources.


  • Evaluation of mechanical deformation and distributive magnetic loads with different mechanical constraints in two parallel conducting bars

    by Ho-Young Lee, Se-Hee Lee

    Mechanical deformation, bending deformation, and distributive magnetic loads were evaluated numerically and experimentally for conducting materials excited with high current. Until now, many research works have extensively studied the area of magnetic force and mechanical deformation by using coupled approaches such as multiphysics solvers. In coupled analysis for magnetoelastic problems, some articles and commercial software have presented the resultant mechanical deformation and stress on the body. To evaluate the mechanical deformation, the Lorentz force density method (LZ) and the Maxwell stress tensor method (MX) have been widely used for conducting materials. However, it is difficult to find any experimental verification regarding mechanical deformation or bending deformation due to magnetic force density. Therefore, we compared our numerical results to those from experiments with two parallel conducting bars to verify our numerical setup for bending deformation. Before showing this, the basic and interesting coupled simulation was conducted to test the mechanical deformations by the LZ (body force density) and the MX (surface force density) methods. This resulted in MX gave the same total force as LZ, but the local force distribution in MX introduced an incorrect mechanical deformation in the simulation of a solid conductor.


  • Characteristics of temperature rise in variable inductor employing magnetorheological fluid driven by a high-frequency pulsed voltage source

    by Ho-Young Lee, In Man Kang, Chae-Hwa Shon, Se-Hee Lee

    A variable inductor with magnetorheological (MR) fluid has been successfully applied to power electronics applications; however, its thermal characteristics have not been investigated. To evaluate the performance of the variable inductor with respect to temperature, we measured the characteristics of temperature rise and developed a numerical analysis technique. The characteristics of temperature rise were determined experimentally and verified numerically by adopting a multiphysics analysis technique. In order to accurately estimate the temperature distribution in a variable inductor with an MR fluid-gap, the thermal solver should import the heat source from the electromagnetic solver to solve the eddy current problem. To improve accuracy, the B–H curves of the MR fluid under operating temperature were obtained using the magnetic property measurement system. In addition, the Steinmetz equation was applied to evaluate the core loss in a ferrite core. The predicted temperature rise for a variable inductor showed good agreement with the experimental data and the developed numerical technique can be employed to design a variable inductor with a high-frequency pulsed voltage source.


  • Numerical and Experimental Validation of Discharge Current With Generalized Energy Method and Integral Ohm's Law in Transformer Oil

    by Ho-Young Lee, Jae-Seung Jung, Hong-Kyu Kim, Il-Han Park, Se-Hee Lee

    The discharge currents were evaluated and validated using the generalized energy method and the integral Ohm's law combined with the recently developed discharge analysis technique for dielectric liquid media, such as transformer oil. The terminal current in voltage-driven systems was found to play an essential role in characterizing the pattern of electric discharge, such as corona, breakdown, etc. Until now, the generalized energy method and integral Ohm's law were normally adopted to evaluate this terminal current, but no experimental validation was reported and no test was performed in a dielectric liquid media. The generalized energy method can be derived directly using Poynting's theorem and is well suited for the finite element method. As an alternative approach, the integral Ohm's law can be applied to multiport systems. To confirm the numerical results, an experimental setup was proposed with a multiport system composed of a tip and separated conducting ring shells. The numerical results were compared with those from experiments, which would be the first trial in a dielectric liquid with a multiport system. The calculated current profile was similar to that from the experimental result, but the breakdown voltage from the calculated results was relatively high.