Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Manuel Alejandro Pedreño-Rojas has a total of 21 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Characterization and performance of building composites made from gypsum and woody-biomass ash waste: A product development and application study

    by Manuel Alejandro Pedreño-Rojas, César Porras-Amores, Paola Villoria-Sáez, María Jesús Morales-Conde, Inês Flores-Colen


  • Open Access

    Sustainable Retrofitting Criteria in Heritage Buildings: Case Study in Seville (Spain)

    by María Cimiano-Prados, Manuel Alejandro Pedreño-Rojas, Jan Fořt, María Jesús Morales-Conde

    The construction sector has an important role to play in reducing the threat of climate change. Thus, this work proposes, analyses, and compares two constructive strategies for the intervention/rehabilitation of a protected building located in Seville (Spain). The first solution intends to follow traditional techniques and standardized criteria, while the second option takes into account environmental aspects for the constructive definition of the proposal. An environmental study of each constructive solution, using a life-cycle assessment methodology, as well as an energy behavior analysis were carried out. The results show that the “sustainable proposal” represents a significant environmental improvement, in which a reduction in CO2 emissions and incorporated energy can be appreciated apart from an optimal energy certification. Finally, the sustainable proposal reveals a significant economic reduction in the total budget of the intervention.


  • Open Access

    Microstructure Formation of Cement Mortars Modified by Superabsorbent Polymers

    by Jan Fořt, Jiří Šál, Martin Böhm, María Jesús Morales-Conde, Manuel Alejandro Pedreño-Rojas, Robert Černý

    The utilization of superabsorbent polymers (SAPs) in cement-based materials has been found to be a promising means of mitigating the autogenous propagation of shrinkage and cracks. On the other hand, the undesired effects of SAPs’ application on functional properties, including mechanical strength, microstructure formation, and the evolution of hydration heat are not properly understood, given the variety in SAPs’ characteristics. To contribute to the present state-of-the-art, cement mortars, modified with two grades of SAPs by dosages of 0.3%, 0.6%, and 0.9%, were designed and studied with emphasis on the relationship between the materials’ porosities and mechanical strengths. The obtained results are interpreted by scanning electron microscopy analysis and hydration heat evolution to elucidate the major changes and their driving factors. Besides the benefits associated with the mitigation of autogenous shrinkage, the achieved results point to an adverse effect of supplementation with SAP on mechanical strength at an early age, and an even more pronounced increase at a later age. The employed scanning electron microscopy images, together with mercury-intrusion porosimetry data, depict distortion in the material porosity as a result of the filling of formed voids and the closing of open ends by swelled hydrogels. Only the minor benefit of a greater cross-linking density was obtained by the formation of dense structures and the gains in mechanical strength therefrom.


  • Open Access

    Use of Bioceramics Enhanced with Effective Microorganisms as an Additive for Construction. Study of Physical and Mechanical Properties in Cement Mortars and Gypsum Plasters

    by Filomena Pérez-Gálvez, María Jesús Morales-Conde, Manuel Alejandro Pedreño-Rojas

    Biomaterials are materials that are used to manufacture devices that interact with biological systems. According to their chemical composition, they can be classified as biometals, biopolymers, bioceramics, biocomposites and semiconductors. Thus, in the present work, the application of bioceramics, enhanced with effective microorganisms, to construction materials (cement mortars and gypsum plasters) was studied in order to see the benefits that its incorporation contributes to construction materials. This first work constitutes the first phase of an experimental campaign in which the influence of bioceramics on the physical and mechanical properties (flexural and compressive strength) of the studied materials was analyzed. Furthermore, scanning electron microscopy (SEM) and mercury intrusion porosimetry (MIP) techniques were used. According to the results, a slight improvement in the mechanical properties of the new composites was observed. Besides, a more compact matrix was observed when bioceramics were used as an aggregate to the mixtures.


  • Open Access

    Eco-Efficient False Ceiling Plates Made from Plaster with Wood and Plastic Residues

    by Manuel Alejandro Pedreño-Rojas, María Jesús Morales-Conde, Filomena Pérez-Gálvez, María Isabel Romero-Gómez, Paloma Rubio-De-Hita

    Large amounts of different types of waste are generated each day in the world. Most of them do not receive proper management at the end of its useful life. In that sense, and trying to apply eco-efficiency criteria, the construction sector has recently been working on the design of new building materials that incorporate some types of residues. Those new construction materials improve some of the properties given by traditional options, such as thermal conductivity or lightness. However, many types of research in which new building products are generated do not exist. Subsequently, this paper aims at generating new gypsum plaster false ceiling plates by incorporating two different types of residues: wood waste from the demolition of traditional wooden slabs and polycarbonate (plastic) waste from crushed rejected CDs and DVDs. The flexural strength of the developed plates is tested using the procedure described by UNE-EN 14246. Furthermore, the thermal conductivity of the new pieces is obtained following the method defined by ASTM D5930-09. The results show that for all the scenarios under study when wood and plastic waste is added to the plates, the lightness and the thermal conductivity of the pieces improved. In addition, in some scenarios, the incorporation of polycarbonate waste is linked to an improvement in the mechanical behaviour of the pieces compared to the reference plate. On the other hand, when wood waste is added to the mixtures, the flexural behaviour of the plates decreases, but always achieving the minimum requirements made by the standards. Finally, it must be said that adding waste to the plasters, the amount of gypsum powder used to generate the plates decreases considerably, which represents a significant improvement in the eco-efficiency of new products.


  • Open Access

    Use of Polycarbonate Waste as Aggregate in Recycled Gypsum Plasters

    by Manuel Alejandro Pedreño-Rojas, Carmen Rodríguez-Liñán, Inês Flores-Colen, Jorge de Brito

    The use of gypsum as an indoor coating material for buildings is very extensive. This means that huge amounts of gypsum waste are generated daily worldwide. Therefore, many researchers in the last years have been working on the generation of new gypsum-related materials and products that incorporate recycled gypsum waste as a replacement for the commercial one. On the other hand, trying to reduce the large amounts of plastic generated globally each year, several studies have used different types of plastic waste as aggregates for the development of new construction and building materials. However, up to now, no previous studies have been found in which any type of plastic waste has been used as an aggregate in a recycled gypsum matrix. This paper presents a study in which two different types of waste were mixed for the development of new gypsum plasters: unheated gypsum waste from industrial plasterboard production (GPW) and polycarbonate (PC) waste from rejected compact discs (CDs) and digital versatile discs (DVDs). In this sense, the mechanical and thermal performance of plasters was evaluated. Finally, in order to evaluate the changes in the microstructure of the composites, a scanning electron microscopy (SEM) analysis was conducted. The results showed a good performance of the new composites when both types of waste were combined in the mixes. New lightweight eco-efficient plasters, completely recycled, with enhanced flexural strength (by 14.8%), compressive strength (by 26.8%), and thermal conductivity (42.8% less), compared to the reference material, were achieved.


  • Open Access

    Reuse of CD and DVD Wastes as Reinforcement in Gypsum Plaster Plates

    by Manuel Alejandro Pedreño-Rojas, María Jesús Morales-Conde, Filomena Pérez-Gálvez, Paloma Rubio-De-Hita

    The continuous and rapid evolution in the field of computing, and in particular in the field of storage devices, has led to the obsolescence of optical discs in favour of mass storage devices. In that sense, a large number of CDs and DVDs become obsolete each day in the world. In trying to create a recovery solution for those pieces, research in which polycarbonate (PC) waste from recycled discs have been used to develop new gypsum coating materials and products has been conducted. In a previous study, the physical and mechanical properties of new gypsum plasters, with PC waste as aggregate, were studied. Following that study, this article aims at creating new gypsum plaster false ceiling plates, using CD and DVD residues in different scenarios: as crushed aggregate in the gypsum matrix, as full reinforcement pieces of the plates and as a combination of both. The mechanical behaviour and the thermal conductivity of the new pieces have been analysed in this paper. The results showed an important improvement in the mechanical and thermal properties of the plates when the PC waste was used in many scenarios.


  • Open Access

    Influence of Wood and Plastic Waste as Aggregates in Gypsum Plasters

    by Manuel Alejandro Pedreno-Rojas, Carmen Rodriguez-Linan, Maria Jesus Morales-Conde, Filomena Perez-Galvez, Paloma Rubio-De-Hita, Maria Isabel Romero-Gomez

    Large amounts of waste are generated each day in the world, being a major concern for the EU28, who establish waste management as a priority line of work within the Horizon 2020. Construction sector is one of the largest residues generators. In that sense, architects and civil engineers should give an answer to solve that environmental problem. One of the options is to reuse waste for the generation of new materials and products for construction. In this research, wood waste (sawdust) from demolition works and polycarbonate waste have been used as aggregates to generate new gypsum plasters. Different percentages of additions (5, 10, 20 and 40%) for each type of waste have been conducted to develop the gypsum composites. Physical (density and thermal conductivity) and mechanical (flexural and compressive strength) properties of the new plasters have been measured using the procedure regulated by standards, comparing them with the reference material values (commercial gypsum without aggregates). The results of the tests show that lighter composites have been obtained when the percentage of waste increased for both type of aggregate. This lightening is higher in composites with wood waste than in those with plastic at the same percentage of addition. Furthermore, an improvement in the thermal conductivity of the plasters have been achieved. On the other hand, a decrease on the mechanical properties of the composites, with higher percentages of additions, have been obtained. For all the cases, the minimum strength value required by standards have been achieved. As a conclusion, lighter gypsum composites with enhanced thermal properties have been obtained, achieving in all the cases an acceptable flexural and compressive strength.


  • Open Access

    Characterisation of recycled ceramic mortars for use in prefabricated beam-filling pieces in structural floors

    by P. Rubio de Hita, F. Pérez-Gálvez, M. J. Morales-Conde, M. A. Pedreño-Rojas

    This study analyses a procedure to manufacture mortars with different percentages of ceramic waste as partial replacement for aggregates. The study also examines the physical, chemical and mechanical properties of the new mortars, analysing substitution ratios that range from 10% to 50%. Prior to this, all the materials used in the production of the mortar were characterised using X-ray diffraction (XRD) and fluorescence (XRF). The objective was to determine the similarity between different types of ceramic waste, as well as the differences in the minerology and chemical composition with the aggregate. The results of the study show that it is possible to obtain mortars with lower densities compared to the same product with no recycled content. The product’s characteristics make it ideal for the manufacture of prefabricated components for structural floors for rehabilitation works. Finally, the pieces are used in a real rehabilitation case study, highlightining the structural advantages.