MLMing Liu

Ming Liu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ming Liu has a total of 48 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Curved Transmitting-Coil Array for Multidimensional Wireless Power Transfer in 3-D Cylindrical Space

    by Ruihan Ma, Shuang Li, Chang Liu, Yu Xiao, Ming Liu, Chengbin Ma

    In recent years, high-frequency wireless power transfer (WPT), such as operating at 6.78 MHz (MHz), has attracted increasing attention due to its improved spatial freedom. In applications such as pipeline inspection robots and medical implants, the transmitting (Tx) coils are usually attached to curved surfaces, and the receiving device often undergoes multi-degree-of-freedom rotations during movement (i.e., positional and angular misalignment). Therefore, this article develops a staggered and overlapping curved Tx-coil array design to achieve a uniform magnetic field distribution in three-dimensional (3D) directions in cylindrical space. The staggered layout is periodic and spatially scalable, overcoming the spatial limitations of traditional designs; the overlapping of each individual curved Tx coil also suppresses the cross-coupling inside the coil array in the 3D direction. In addition, Tx input current phase modulation is applied to shape the magnetic field in the cylindrical space. Finally, the concept of the staggered curved coil array is implemented and verified in a 6.78 MHz WPT experimental system. The results show that the design greatly improves the spatial freedom of power transfer in 3D cylindrical space with a static and pre-optimized manner (i.e., no adaptation), especially showing high tolerance to rotations with position and angle misalignment. For instance, when charging a planar receiver with misaligned position and 20$^{\circ }$ titled angle, the coefficient of variation of the received output voltage is reduced to 6.5% over a 360$^{\circ }$ rotation.

  • Optimal Trajectory Control Scheme for Dual-Bridge Series-Resonant Converters With Constant and Small Low-Voltage Side Turn-Off Current

    by Chang Liu, Haojun Qin, Ming Liu, Chengbin Ma

    With the emerging of large-capacity battery cells, the demand of high-current, high-conversion-ratio bidirectional dc-dc converters in energy storage systems (ESS) has also increased. Similarly, electric vehicle on-board chargers (OBC) face the same requirement when charging or discharging low-voltage (LV) batteries. Although conventional approaches such as inductor-inductor-capacitor converter (LLC) have provided good performance, their LV transistors still suffer from large switching stress during conversions from the LV side to the high-voltage (HV) side. In addition, due to the resonance, load transition response is slow and resonant amplitude oscillates during transients, which further increases the LV switching stress. To overcome these two shortcomings, an optimal trajectory control (OTC) based control for dual-active-bridge series-resonant converter (DBSRC) is proposed. It uses state-plane analysis (SPA) to find mode length solutions with the following two properties: First, for all the steady-state and transition solutions, zero-voltage switching (ZVS) always holds and the LV switching stress is constant and small; Second, transitions converge within one cycle and the resonant amplitude does not oscillate or overshoot. To validate the proposed solution, steady state tests, open-loop power transition tests and closed-loop load transition tests are conducted on a 3 kW prototype. In all tests, ZVS and small turn-off current are observed in every cycle, which is consistent with expectations. Besides, single-cycle convergence and fast load transition response are also verified.


  • Mathieu Equation-Based Analysis and Suppression Approach of Subharmonic Oscillations in High-Frequency Switched-Mode Power Amplifiers

    by Wei Liu, Ming Liu

    Switched-Mode Power Amplifiers (SMPAs) are preferable in high-power applications due to their advantage of high efficiency. Whereas the undesirable effects of parasitics in the switches and circuits highly affect their applications at higher frequencies. Though the parasitic effects (e.g., natural ringing down and self-sustained oscillations) have been explicitly investigated, subharmonic oscillations (which cause high-voltage pressure and significant subharmonic distortion) have not received adequate study in SMPAs. Therefore, this paper presents a detailed analysis to reveal the mechanism of subharmonic oscillations in SMPAs. According to the analysis, unlike the linear PAs, the non-linear output capacitance (Coss) of MOSFETs was found to be the main contributor to the subharmonic oscillations in SMPAs. Furthermore, the load branch plays a damping role, and the simplification to describe the damping effect of load parameters, such as load resistance and quality factor, is discussed. Since the Coss current is difficult to solve explicitly due to the nonlinear differential equations, a Mathieu Equation-based approach is proposed to describe the variation tendency of the current and evaluate the operation stability of SMPAs. Based on the above analysis, the design-oriented and damping tank-based suppression methods are presented to mitigate the subharmonic oscillations. The proposed analysis and design approach is experimentally validated through a 13.56MHz Class E PA, and the experimental and simulated results match well with the analysis. With the proposed suppression methods, the subharmonic oscillations can be eliminated over the whole voltage modulation range.

  • Comprehensive Impedance Analysis and Region-to-Region Transformation for Megahertz Wireless Power Transfer Systems

    by Zhan Liu, Yu Xiao, Ming Liu, Chengbin Ma

    This article presents a comprehensive impedance analysis of megahertz (MHz) wireless power transfer (WPT) systems considering load variations, coil misalignment and non-ideal factors including device parasitics and coil compensation error. The analysis shows that for the MHz operation, the above two non-ideal factors substantially enlarge the variation region of power amplifier's (PA) load impedance, which may adversely affect the stable operation of the MHz WPT systems in practical scenarios. This observation results in the development of a new region-to-region impedance matching network (IMN) design to enhance the robustness of the MHz WPT systems rather than existing ideal trajectory-to-trajectory or point-to-point impedance transformation. Specifically, the Möbius transformation is chosen as a tool to calculate the region-to-region IMN parameters due to its circularity-preserving property. The determination of initial and target PA impedance regions and solution of the Möbius transformation-based IMN design are further discussed from a system-level perspective. Experimental results show significantly improved stable operation of an actual 6.78 MHz WPT system with the proposed region-to-region impedance matching. With a $\pm 3\%$ coupled coil compensation error, the experimental MHz WPT system achieves a system efficiency of 82–87% under a 15-50 $\Omega$ dc load variation, and the system efficiency ranges between 81.18-87.50% with a varying mutual inductance coefficient $k$ between 0.086–0.161.


  • A Möbius Transformation Impedance Matching Approach for Large Load Region and Multilevel Power Modulation in High Frequency Switched Mode Power Amplifier

    by Yongzhi Zhu, Wei Liu, Yaoxia Shao, Ming Liu

    The switched mode power amplifier (PA) is widely used for high frequency high power applications due to its high efficiency. In the switched mode PAs, impedance matching network (IMN) is usually needed to ensure that the varying load impedances can be matched to the target impedances for high efficiency. The existing IMN design methods usually depend on empirical trial and error, load pull simulation, and numerical optimization, which cannot achieve actual region-to-region impedance matching. Therefore, this article proposed a novel impedance matching design approach for switch mode PAs based on the property of circle preservation in Möbius transformation which guarantee that all the impedance points in a region or trajectory can be precisely transferred to the target region or trajectory. The proposed approach gives the simple and explicit formulas to design the IMN parameters, which helps solve the design challenge of accurate impedance matching for large load region. And the impedance matching design for frequency tuning control is also presented to achieve high efficiency and multilevel power modulation over a large impedance region. For verification, a 500 W 13.56 MHz GaN-based class E PA is built and the experiments show that the PA with proposed matching design can achieve 87.2%–95% efficiency over a large load region. And the high speed pulsing (200 kHz) and multilevel (25.6 kHz) power modulation can be also achieved by frequency tuning with ultra-fast transitions (369 ns) and 91% average efficiency by using the proposed design.


  • Continuous-Control-Set Model Predictive Control-Based Energy Routing With Over/Under Voltage Protection

    by Haojun Qin, Chang Liu, Yang Shi, Ming Liu, Chengbin Ma

    Multiactive-bridge (MAB) converters are highly promising as energy routers in renewable energy applications. Their multiple-input multiple-output control challenges can be effectively addressed by a model predictive control (MPC) approach, which minimizes the interference between different ports and simplifies the controller design. However, during the optimization process, the input and output constraints are usually ignored to simplify the implementation, which may degrade the control performance and lead to large voltage overshoot/undershoot when the constraints are violated. Meanwhile, solving the constrained MPC problem within a short sampling time poses a huge computational challenge. To address these issues, in this article a continuous-control-set model predictive control (CCS-MPC) scheme is developed for the MAB converters, which incorporates input and output constraints to achieve over/under voltage protection. An MPC problem with multiple constraints is formulated and converted into a quadratic programming (QP) problem. Its real-time implementation on a low-cost microcontroller unit is further discussed including QP solver deployment, real-time certification, and delay compensation. Finally, the developed CCS-MPC scheme is experimentally verified by a four-port 500 W energy router prototype and well demonstrates the over/under voltage protection capability.


  • A High Frequency Active Clamping Source Based SiC Resonant Gate Driving Technology for Multi-kW and Tens of MHz Switched Mode Power Amplifier

    by Wei Liu, Yongzhi Zhu, Ming Liu

    Resonant gate driver (RGD) is an effective method to achieve gate driving loss reduction and noise suppression at high frequency. Most RGDs require at least two switches to constitute the bridge structure, which suffers from the difficulty of accurate dead time control at tens of MHz. The single-switch RGDs are easy to implement but can only generate fixed duty cycle driving voltage and operate at the narrow band. Thus, this article proposed a single-switch resonant gate driving technology with adjustable duty cycle and wide bandwidth operation for multi-kW and tens of MHz SiC-based power amplifiers. The proposed technology introduces an active clamping source to control the duty cycle of the gate-source voltage of the main switch by tuning the dc supply voltage, which is much easier than tuning the duty cycle of pulse width modulation (PWM) signals at the nanosecond level. In the proposed RGD, a resonant tank and two clamping diodes are employed to coordinate the active clamping source for gate driving loss reduction, fast turn-on/off gate driving, and gate oscillation suppression. An explicit design methodology was proposed to determine its circuit parameters for zero voltage switching (ZVS) and fast turn-on/off operations across duty cycle and frequency modulations. For verification, a prototyping system of the proposed RGD is built to drive a 1.2 kW Class-E power amplifier with frequency and duty cycle modulations (12 MHz–15 MHz and 40%–60%), where 82.4% gate driving loss reduction and 92.6% power amplifier efficiency are achieved.


  • Extended Phasor Analysis Approach and Control Strategy for Flexible Multiway Power Flow and Wide ZVS Operation in the Multiport Wireless Power Router

    by Yifan Wang, Miao Zhu, Ming Liu

    This article proposes a multiport wireless power router (MWPR) and its control strategy which is capable of processing multiway bidirectional power flow and can be potentially applied in multiport power processing applications, such as battery management and interfacing systems. The MWPR connects multiple sources and loads through vertically stacked coils, providing several potential power channels regardless of which ports are connected to the system. This significantly enhances the system’s flexibility and enables it to perform various functions. Key contributions of this article include: 1) an equivalent-port model for simplifying the analysis of multiple power flow and zero voltage switching (ZVS) conditions; 2) an extended phasor analysis approach for intuitively revealing the interaction between power flow, ZVS operation and control variables; 3) a multi-objective control strategy for flexible power flow modulation and wide range ZVS operation. To validate the proposed modeling, analysis, and control strategy, a 250 kHz 4-port MWPR prototype is built and tested. Experimental results indicate that flexible multi-way power flow modulation and ZVS operation are achieved over a wide power range and under different port voltages.