Zhengwei Xiong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhengwei Xiong has a total of 165 co-authors. Here are the top co-authors by number of shared publications:
- Zhipeng Gao
Institute of Fluid Physics, China Academy of Engineering Physics 2 , Mianyang 621900
16 shared publications Zhipeng Gao
11 shared publicationsLeiming Fang
10 shared publicationsJia Yang
Institute of Fluid Physics
8 shared publicationsJun Li
Southwest Institute of Applied Magnetics, Mianyang 621010, P. R. China
8 shared publications- Xiaoru Liu
Joint Laboratory for Extreme Conditions Matter Properties, School of Mathematics and Physics, Southwest University of Science and Technology 1 , Mianyang 621010
8 shared publications
Latest Publications
- Open Access
- 3 September 2026
- Published by Elsevier in SSRN Electronic Journal
Fracture behaviors governed by interfacial bonding effect in epoxy composites
Epoxy composites are widely applied in electronics, aerospace, artificial intelligence and other fields, where their mechanical properties, particularly fracture behaviors, are crucial to material design. Prior studies have primarily attributed fracture behavior to the intrinsic strength and toughness of the epoxy matrix and the reinforcing effects of fillers, while relatively limited attention has been paid to the role of interfacial bonding, which may lead to an incomplete understanding of the mechanisms governing fracture in epoxy composites. Here, the mechanical properties and fracture behaviors of epoxy composites with different rigid fillers were systematically investigated. Both Al2O3 and SiO2 fillers improved the mechanical properties while the fracture characteristics exhibit distinct difference. Epoxy/Al2O3 exhibited highest fracture toughness at 10 wt.%, whereas higher filler content induced filler agglomeration and interfacial debonding, facilitating interfacial crack propagation and reducing fracture toughness. In contrast, epoxy/SiO2 displayed continuously enhanced fracture toughness with increasing filler content, owing to enhanced energy dissipation from crack deflection and tortuous crack paths. Besides, First-principles calculations further revealed that epoxy/SiO2 interface has higher interfacial bonding strength compared with epoxy/Al2O3 interface. These results demonstrate that interfacial bonding strength governs crack propagation behavior and fracture performance. Based on experimental measurements and first-principles calculations, an interfacial bonding-mediated crack propagation model was constructed herein, delivering innovative perspectives and technical guidance for high-strength epoxy composites.
- 3 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessFracture behaviors governed by interfacial bonding effect in epoxy composites
Epoxy composites are widely applied in electronics, aerospace, artificial intelligence and other fields, where their mechanical properties, particularly fracture behaviors, are crucial to material design. Prior studies have primarily attributed fracture behavior to the intrinsic strength and toughness of the epoxy matrix and the reinforcing effects of fillers, while relatively limited attention has been paid to the role of interfacial bonding, which may lead to an incomplete understanding of the mechanisms governing fracture in epoxy composites. Here, the mechanical properties and fracture behaviors of epoxy composites with different rigid fillers were systematically investigated. Both Al2O3 and SiO2 fillers improved the mechanical properties while the fracture characteristics exhibit distinct difference. Epoxy/Al2O3 exhibited highest fracture toughness at 10 wt.%, whereas higher filler content induced filler agglomeration and interfacial debonding, facilitating interfacial crack propagation and reducing fracture toughness. In contrast, epoxy/SiO2 displayed continuously enhanced fracture toughness with increasing filler content, owing to enhanced energy dissipation from crack deflection and tortuous crack paths. Besides, First-principles calculations further revealed that epoxy/SiO2 interface has higher interfacial bonding strength compared with epoxy/Al2O3 interface. These results demonstrate that interfacial bonding strength governs crack propagation behavior and fracture performance. Based on experimental measurements and first-principles calculations, an interfacial bonding-mediated crack propagation model was constructed herein, delivering innovative perspectives and technical guidance for high-strength epoxy composites.
- Open Access
- 18 July 2026
- Published by Elsevier in SSRN Electronic Journal
Synergetic improvement of magnetic and mechanical performance in 2:17-type SmCo magnet via hot-press sintering
To overcome the limitations of conventional vacuum sintering for 2:17-type SmCo permanent magnets, including grain coarsening, Sm evaporation, and insufficient mechanical performance, this work systematically investigated the effects of hot-press sintering on their microstructure, magnetic properties, and mechanical properties. The results exhibit that hot-press sintering achieves high densification at relatively low temperatures, while refining grains and improving grain uniformity. After heat treatment, the magnetic properties are further enhanced. The sample hot-pressed at 1080 °C exhibits optimal performance, with a maximum energy product ((BH)max) of 30.46 MGOe and a remanence (Br) of 11.46 kGs, exceeding those of the vacuum-sintered sample (29.84 MGOe and 11.23 kGs). Meanwhile, the compressive and flexural strengths reach 985.6 MPa and 115.2 MPa, respectively, surpassing the vacuum-sintered sample. The enhanced mechanical properties are mainly attributed to grain refinement, improved grain uniformity, and the inhibition of crack propagation by precipitated phases. This study provides an effective approach for the simultaneous optimization of magnetic and mechanical properties in high-performance SmCo permanent magnets.
- 18 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSynergetic improvement of magnetic and mechanical performance in 2:17-type SmCo magnet via hot-press sintering
To overcome the limitations of conventional vacuum sintering for 2:17-type SmCo permanent magnets, including grain coarsening, Sm evaporation, and insufficient mechanical performance, this work systematically investigated the effects of hot-press sintering on their microstructure, magnetic properties, and mechanical properties. The results exhibit that hot-press sintering achieves high densification at relatively low temperatures, while refining grains and improving grain uniformity. After heat treatment, the magnetic properties are further enhanced. The sample hot-pressed at 1080 °C exhibits optimal performance, with a maximum energy product ((BH)max) of 30.46 MGOe and a remanence (Br) of 11.46 kGs, exceeding those of the vacuum-sintered sample (29.84 MGOe and 11.23 kGs). Meanwhile, the compressive and flexural strengths reach 985.6 MPa and 115.2 MPa, respectively, surpassing the vacuum-sintered sample. The enhanced mechanical properties are mainly attributed to grain refinement, improved grain uniformity, and the inhibition of crack propagation by precipitated phases. This study provides an effective approach for the simultaneous optimization of magnetic and mechanical properties in high-performance SmCo permanent magnets.
- 1 April 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (14) , 20657-20667
Ultrahigh Polarization-Temperature-Stability 0.95PZ–0.05BMN Ferroelectrics for Energy Conversion Application
Ferroelectric materials offer promising prospects for explosive energy conversion applications owing to their capability to deliver extremely high pulsed power. Unfortunately, the disadvantage of polarization temperature stability especially under a harsh environment poses a significant challenge to application. In this work, we report a 0.95PbZrO3-0.05Ba(Mg1/3Nb2/3)O3 ferroelectric ceramic that simultaneously exhibits a high remnant polarization (Pr) of ∼35.3 μC/cm2 and outstanding polarization temperature stability (i.e., less than 5.1% in a large temperature range from 30 °C to 110 °C). In-situ structural analyses, designed to elucidate the physical mechanisms underlying Pr temperature stability, reveal that ultrahigh temperature stability is due to a stable single rhombohedral phase with an ordered lattice structure, in accordance with a stable oxygen octahedron tilt up to the Curie temperature (∼200 °C). Finally, the pressure-driven ferroelectric-antiferroelectric phase transition depolarization behaviors under hydrostatic pressure and shock compression were achieved from an application perspective. The proposed composition of 0.95PbZrO3-0.05Ba(Mg1/3Nb2/3)O3 provides not only a promising material for energy harvesting and energy conversion applications, but also a paradigm for the design of other ferroelectric materials with ultrahigh polarization temperature stability.
- 1 April 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (14) , 20657-20667
Ultrahigh Polarization-Temperature-Stability 0.95PZ–0.05BMN Ferroelectrics for Energy Conversion Application
Ferroelectric materials offer promising prospects for explosive energy conversion applications owing to their capability to deliver extremely high pulsed power. Unfortunately, the disadvantage of polarization temperature stability especially under a harsh environment poses a significant challenge to application. In this work, we report a 0.95PbZrO3-0.05Ba(Mg1/3Nb2/3)O3 ferroelectric ceramic that simultaneously exhibits a high remnant polarization (Pr) of ∼35.3 μC/cm2 and outstanding polarization temperature stability (i.e., less than 5.1% in a large temperature range from 30 °C to 110 °C). In-situ structural analyses, designed to elucidate the physical mechanisms underlying Pr temperature stability, reveal that ultrahigh temperature stability is due to a stable single rhombohedral phase with an ordered lattice structure, in accordance with a stable oxygen octahedron tilt up to the Curie temperature (∼200 °C). Finally, the pressure-driven ferroelectric-antiferroelectric phase transition depolarization behaviors under hydrostatic pressure and shock compression were achieved from an application perspective. The proposed composition of 0.95PbZrO3-0.05Ba(Mg1/3Nb2/3)O3 provides not only a promising material for energy harvesting and energy conversion applications, but also a paradigm for the design of other ferroelectric materials with ultrahigh polarization temperature stability.
- 30 March 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (13)
Electrical response of YCOB single crystal under shock compression
Shock wave pressure sensors play a crucial role in explosion and impact dynamics as well as aerospace engine monitoring, yet conventional sensors are limited by the intrinsic properties of their core materials, preventing stable operation under high-temperature and high-pressure conditions. Yttrium calcium oxyborate (YCOB) single crystals, with high thermal stability and resistivity, have emerged as promising candidates for next-generation high-temperature sensors. Herein, the shock-induced electrical response of YCOB single crystals was systematically investigated using a gas gun at room temperature and 590 °C. The peak current increases with shock pressure, showing temperature-independent behavior and confirming the feasibility of high-temperature shock measurements. A numerical model describing the dynamic response of piezoelectric materials was established, providing insights into their discharge mechanisms under dynamic loading. Theoretical analysis indicates that YCOB-based sensors can detect higher-magnitude shock pressures at elevated temperatures compared with conventional devices. These findings provide a foundation for designing high-temperature shock pressure sensors and for studying the shock dynamics of YCOB materials.
- 30 March 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (13)
Electrical response of YCOB single crystal under shock compression
Shock wave pressure sensors play a crucial role in explosion and impact dynamics as well as aerospace engine monitoring, yet conventional sensors are limited by the intrinsic properties of their core materials, preventing stable operation under high-temperature and high-pressure conditions. Yttrium calcium oxyborate (YCOB) single crystals, with high thermal stability and resistivity, have emerged as promising candidates for next-generation high-temperature sensors. Herein, the shock-induced electrical response of YCOB single crystals was systematically investigated using a gas gun at room temperature and 590 °C. The peak current increases with shock pressure, showing temperature-independent behavior and confirming the feasibility of high-temperature shock measurements. A numerical model describing the dynamic response of piezoelectric materials was established, providing insights into their discharge mechanisms under dynamic loading. Theoretical analysis indicates that YCOB-based sensors can detect higher-magnitude shock pressures at elevated temperatures compared with conventional devices. These findings provide a foundation for designing high-temperature shock pressure sensors and for studying the shock dynamics of YCOB materials.
- 8 December 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (23)
Electric field tuning phase transition behavior and the discharge performance of (Na0.5Bi0.5)TiO3 ferroelectric ceramics under shock compression
Ferroelectric materials, owing to their polar structures and spontaneous polarization, can rapidly release charges under shock loading, offering striking potential for high-power pulsed power sources and energy conversion devices. In practical applications, ferroelectrics often operate under coupled pressure–electric field environments, where their phase transition behavior plays a key role in determining electrical responses. However, the phase transition mechanisms and phase diagrams under such coupled conditions remain unclear, and the output current lacks effective regulation. Here, the discharge behavior of (Na0.5Bi0.5)TiO3 ferroelectric ceramics under coupled pressure–electric field conditions is investigated. Experiments reveal that increasing shock pressure promotes the ferroelectric–paraelectric transition and enhances charge release, while the electric field suppresses the transition, enabling effective control of the peak output current and phase transition ratio. This breaks the limitation of fixed current amplitude under shock conditions. Furthermore, a three-dimensional electric field-pressure-charge release map and a pressure–electric field phase diagram are established, unveiling the competitive interplay between pressure and electric field in governing the ferroelectric–paraelectric transition. These findings provide guidance for the design and application of lead-free ferroelectric ceramics in extreme multi-field environments.
- 8 December 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (23)
Electric field tuning phase transition behavior and the discharge performance of (Na0.5Bi0.5)TiO3 ferroelectric ceramics under shock compression
Ferroelectric materials, owing to their polar structures and spontaneous polarization, can rapidly release charges under shock loading, offering striking potential for high-power pulsed power sources and energy conversion devices. In practical applications, ferroelectrics often operate under coupled pressure–electric field environments, where their phase transition behavior plays a key role in determining electrical responses. However, the phase transition mechanisms and phase diagrams under such coupled conditions remain unclear, and the output current lacks effective regulation. Here, the discharge behavior of (Na0.5Bi0.5)TiO3 ferroelectric ceramics under coupled pressure–electric field conditions is investigated. Experiments reveal that increasing shock pressure promotes the ferroelectric–paraelectric transition and enhances charge release, while the electric field suppresses the transition, enabling effective control of the peak output current and phase transition ratio. This breaks the limitation of fixed current amplitude under shock conditions. Furthermore, a three-dimensional electric field-pressure-charge release map and a pressure–electric field phase diagram are established, unveiling the competitive interplay between pressure and electric field in governing the ferroelectric–paraelectric transition. These findings provide guidance for the design and application of lead-free ferroelectric ceramics in extreme multi-field environments.
- 10 November 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (19)
Synergistic hardening and rotational mechanism of the multiscale heterogeneous structure in the (CoCrNi)90Al10 medium-entropy alloy
Designing heterogeneous structures is a proven strategy to overcome the strength–ductility trade-off in metallic materials by introducing additional hetero-deformation-induced (HDI) hardening. However, the quantitative differences in HDI hardening arising from various types of heterogeneity, as well as their respective dominant roles during deformation, remain poorly understood. In this work, a multiscale heterogeneous structure was engineered in a (CoCrNi)90Al10 medium-entropy alloy to reveal the distinct HDI hardening contributions of lamellar and hierarchical grain structure. The resulting alloy exhibits significantly enhanced tensile properties, attributed to the synergy of two rotation-mediated hardening mechanisms. Specifically, the lamellar architecture, composed of deformed grains and recrystallized micrometer-sized grains, provides pronounced HDI hardening at the early stage of deformation due to a higher density of hetero-interfaces. As deformation progresses, hierarchical grains, formed via dynamic grain refinement within the recrystallized regions, gradually dominate the heterogeneous deformation behavior. This is driven by the increasing fraction of fine micrometer grain interfaces and the higher accumulation of geometrically necessary dislocations at these boundaries. This study not only elucidates the distinct hardening mechanisms of lamellar and hierarchical hetero-structures but also offers some guidance for the rational design of high-performance structural alloys.
- 10 November 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (19)
Synergistic hardening and rotational mechanism of the multiscale heterogeneous structure in the (CoCrNi)90Al10 medium-entropy alloy
Designing heterogeneous structures is a proven strategy to overcome the strength–ductility trade-off in metallic materials by introducing additional hetero-deformation-induced (HDI) hardening. However, the quantitative differences in HDI hardening arising from various types of heterogeneity, as well as their respective dominant roles during deformation, remain poorly understood. In this work, a multiscale heterogeneous structure was engineered in a (CoCrNi)90Al10 medium-entropy alloy to reveal the distinct HDI hardening contributions of lamellar and hierarchical grain structure. The resulting alloy exhibits significantly enhanced tensile properties, attributed to the synergy of two rotation-mediated hardening mechanisms. Specifically, the lamellar architecture, composed of deformed grains and recrystallized micrometer-sized grains, provides pronounced HDI hardening at the early stage of deformation due to a higher density of hetero-interfaces. As deformation progresses, hierarchical grains, formed via dynamic grain refinement within the recrystallized regions, gradually dominate the heterogeneous deformation behavior. This is driven by the increasing fraction of fine micrometer grain interfaces and the higher accumulation of geometrically necessary dislocations at these boundaries. This study not only elucidates the distinct hardening mechanisms of lamellar and hierarchical hetero-structures but also offers some guidance for the rational design of high-performance structural alloys.
- 17 February 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (7)
Difference between dynamic and hydrostatic pressure-induced phase transition behaviors of ferroelectric ceramics
PZT95/5 is a widely used ferroelectric material renowned for its exceptional ferroelectric properties, making it a crucial component in pulsed power systems and advanced devices. The phase transition behavior of ferroelectric ceramics under compression is vital for the effective design of materials and devices. The phase transition processes in these ceramics differ significantly between static and dynamic compression, presenting a long-standing controversy in the field. This study investigates the phase transition of PZT95/5 under dynamic shock compression using a shock response model. The findings indicate that the dynamic phase transition begins at lower pressures and completes at higher pressures compared to hydrostatic conditions, resulting in a broader pressure range for the phase transition. Theoretical modeling, grounded in ferroelectric and piezoelectric effects, combined with one-dimensional uniaxial stress density functional theory calculations across various orientations and three-dimensional Python visualizations, clarifies the physical mechanisms driving the progressive phase transition of ceramics under dynamic conditions. Additionally, the dynamic phase transition ratio of the ferroelectric material is quantified. Under hydrostatic pressures, the phase transition is independent of grain orientation, resulting in consistent transition pressures across all directions. In contrast, under anisotropic stress, grains with different orientations exhibit varying sensitivity to pressures, leading to distinct transition pressures in each direction. These insights advance the understanding of the phase transition mechanisms governing ferroelectric ceramics under both static and dynamic pressures.
- 17 February 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (7)
Difference between dynamic and hydrostatic pressure-induced phase transition behaviors of ferroelectric ceramics
PZT95/5 is a widely used ferroelectric material renowned for its exceptional ferroelectric properties, making it a crucial component in pulsed power systems and advanced devices. The phase transition behavior of ferroelectric ceramics under compression is vital for the effective design of materials and devices. The phase transition processes in these ceramics differ significantly between static and dynamic compression, presenting a long-standing controversy in the field. This study investigates the phase transition of PZT95/5 under dynamic shock compression using a shock response model. The findings indicate that the dynamic phase transition begins at lower pressures and completes at higher pressures compared to hydrostatic conditions, resulting in a broader pressure range for the phase transition. Theoretical modeling, grounded in ferroelectric and piezoelectric effects, combined with one-dimensional uniaxial stress density functional theory calculations across various orientations and three-dimensional Python visualizations, clarifies the physical mechanisms driving the progressive phase transition of ceramics under dynamic conditions. Additionally, the dynamic phase transition ratio of the ferroelectric material is quantified. Under hydrostatic pressures, the phase transition is independent of grain orientation, resulting in consistent transition pressures across all directions. In contrast, under anisotropic stress, grains with different orientations exhibit varying sensitivity to pressures, leading to distinct transition pressures in each direction. These insights advance the understanding of the phase transition mechanisms governing ferroelectric ceramics under both static and dynamic pressures.
- 7 November 2024
- Published by American Chemical Society (ACS) in Inorganic Chemistry
- Vol. 63 (46) , 22227-22238
Polymorphism in Type-II Dirac Semimetal WSi2 under Pressure: Structural, Mechanical, and Electronic Insights
- 7 November 2024
- Published by American Chemical Society (ACS) in Inorganic Chemistry
- Vol. 63 (46) , 22227-22238
Polymorphism in Type-II Dirac Semimetal WSi2 under Pressure: Structural, Mechanical, and Electronic Insights
- 5 November 2024
- Published by American Physical Society (APS) in Physical Review B
- Vol. 110 (17)
Dynamic phase transition modeling of potassium niobate under shock compression
- 5 November 2024
- Published by American Physical Society (APS) in Physical Review B
- Vol. 110 (17)
Dynamic phase transition modeling of potassium niobate under shock compression