Ke Han
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ke Han has a total of 123 co-authors. Here are the top co-authors by number of shared publications:
- Rongmei Niu
National High Magnetic Field Laboratory, Tallahassee, FL, USA
12 shared publications - Jun Lu
Magnetic Science and Technology National High Magnetic Field Laboratory Tallahassee Florida USA
9 shared publications Yan Xin
7 shared publications- Yan Xin
National High Magnetic Field Laboratory
7 shared publications - Qijie Zhai
Center for Advanced Solidification Technology of Shanghai University, State Key Laboratory of Materials for Advanced Nuclear Energy, Shanghai, P.R. China
6 shared publications - Doan Ngoc Nguyen
Los Alamos National Laboratory
5 shared publications
Latest Publications
- Open Access
- 21 October 2026
- Published by Elsevier in SSRN Electronic Journal
A comprehensive electron microscopy study of alumina particles and associated defects in commercial high-strength oxide-dispersion-strengthened GLIDCOP® copper wires
Certain oxide-dispersion-strengthened copper wires are commercially available such as GLIDCOP® AL-15 and AL-60, which are used in many applications including building high field pulsed magnets. We studied the microstructures of these wires by electron microscopy. The alumina particles formed through internal oxidation dispersed in copper had sizes from 3 nm to 100 nm, most of which had a cubic spinel γ crystal structure with exception of some medium sized particles of around 50 nm with γ’ or δ metastable crystal structure. In contrast, the larger particles from added alumina with oxidant above 100 nm up to 1 µm or larger in size had the stable hexagonal α crystal structure. Small and medium alumina particles had modal diameters of 6 nm and 30 nm for AL-15, compared to 10 nm and 32 nm for AL-60. Both AL-15 and AL-60 had comparable size distribution of the internal oxidized alumina, forming bands of the same sized particles along the drawing direction across the wire width. The oval or round-shaped alumina particles had no fixed crystallographic orientation relationship with the Cu matrix, and the regions with big particles were associated with the Cu grains free of internal alumina particles. Additional defects such as stacking faults and Frank partial dislocation loops in Cu are associated with internal oxidized alumina particles. The yield strength of the wires mainly has three major strengthening contributions: work hardening from dislocations, grain boundary strengthening and Orowan strengthening by the internal oxidized alumina particles. The weakest area of the GLIDCOP® wire with the highest possibility of fracture might be the Cu region with the big α-Al2O3 particles containing no internal oxidized alumina particles. Through this study, we reported a comprehensive picture of the microstructures of the wires that are essential for understanding their mechanical properties.
- 21 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessA comprehensive electron microscopy study of alumina particles and associated defects in commercial high-strength oxide-dispersion-strengthened GLIDCOP® copper wires
Certain oxide-dispersion-strengthened copper wires are commercially available such as GLIDCOP® AL-15 and AL-60, which are used in many applications including building high field pulsed magnets. We studied the microstructures of these wires by electron microscopy. The alumina particles formed through internal oxidation dispersed in copper had sizes from 3 nm to 100 nm, most of which had a cubic spinel γ crystal structure with exception of some medium sized particles of around 50 nm with γ’ or δ metastable crystal structure. In contrast, the larger particles from added alumina with oxidant above 100 nm up to 1 µm or larger in size had the stable hexagonal α crystal structure. Small and medium alumina particles had modal diameters of 6 nm and 30 nm for AL-15, compared to 10 nm and 32 nm for AL-60. Both AL-15 and AL-60 had comparable size distribution of the internal oxidized alumina, forming bands of the same sized particles along the drawing direction across the wire width. The oval or round-shaped alumina particles had no fixed crystallographic orientation relationship with the Cu matrix, and the regions with big particles were associated with the Cu grains free of internal alumina particles. Additional defects such as stacking faults and Frank partial dislocation loops in Cu are associated with internal oxidized alumina particles. The yield strength of the wires mainly has three major strengthening contributions: work hardening from dislocations, grain boundary strengthening and Orowan strengthening by the internal oxidized alumina particles. The weakest area of the GLIDCOP® wire with the highest possibility of fracture might be the Cu region with the big α-Al2O3 particles containing no internal oxidized alumina particles. Through this study, we reported a comprehensive picture of the microstructures of the wires that are essential for understanding their mechanical properties.
- Open Access
- 13 July 2026
- Published by Springer Nature in MRS Advances
- Vol. 11 (9) , 987-993
Microstructural examination of Cu-Nb and Cu-Nb-Ag composites
- 13 July 2026
- Published by Springer Nature in MRS Advances
- Vol. 11 (9) , 987-993
Open AccessMicrostructural examination of Cu-Nb and Cu-Nb-Ag composites
- 26 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-6
Recent Magnet Developments at the Pulsed Field Facility (NHMFL) at Los Alamos
The National High Magnetic Field Laboratory (NHMFL) – Pulsed Field Facility (PFF) at Los Alamos operates ten pulsed magnet stations that deliver magnetic fields up to 100 Tesla for user experiments. In recent years, PFF has enhanced its capabilities with upgraded magnets, enabling the generation of higher magnetic fields and an increased number of pulses. This manuscript will provide an overview of recent magnet developments at the PFF, including the performance of new systems such as the 75-T duplex and 60-T Mid-pulsed magnets. Additionally, a novel cooling technique that significantly reduces cooling time without compromising magnet lifespan or stability will be discussed. Lastly, the maintenance and upgrades for our facility's signature magnet systems, including the 100-T multi-shot and 60-T controlled-waveform magnets will be covered.
- 26 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-6
Recent Magnet Developments at the Pulsed Field Facility (NHMFL) at Los Alamos
The National High Magnetic Field Laboratory (NHMFL) – Pulsed Field Facility (PFF) at Los Alamos operates ten pulsed magnet stations that deliver magnetic fields up to 100 Tesla for user experiments. In recent years, PFF has enhanced its capabilities with upgraded magnets, enabling the generation of higher magnetic fields and an increased number of pulses. This manuscript will provide an overview of recent magnet developments at the PFF, including the performance of new systems such as the 75-T duplex and 60-T Mid-pulsed magnets. Additionally, a novel cooling technique that significantly reduces cooling time without compromising magnet lifespan or stability will be discussed. Lastly, the maintenance and upgrades for our facility's signature magnet systems, including the 100-T multi-shot and 60-T controlled-waveform magnets will be covered.
- 24 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Fatigue Properties of Cold-Rolled Cu-Zr Alloy Sheets
We performed tension-tension fatigue tests in stress control mode on cold-rolled Cu-Zr alloy sheets with various levels of tensile strength (TS). We then compared the fatigue properties of these sheets to those of cold-rolled Cu sheets. Fatigue life increased as TS increased. We separated our Cu-Zr sheets according to their mechanical strength levels, designating those with their TS ∼490 MPa as “H”, those with TS around 448 $ \pm $ 5 MPa as “M”, and those with TS < 440 MPa as “L”. The “H” sheets exhibited the longest life, followed by the “M” sheets, and the “L” sheets, all outperforming Cu. At 390 MPa. “H” Cu-Zr’s fatigue life was ∼3 times that of Cu. Both the Cu-Zr and the Cu showed cyclic hardening. The presence of Zirconium improved fatigue life by stabilizing microstructure and retarding the formation of cracks during fatigue cycling, thus positioning Cu-Zr alloys as much stronger candidates than Cu for resistive magnet conductors.
- 24 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Fatigue Properties of Cold-Rolled Cu-Zr Alloy Sheets
We performed tension-tension fatigue tests in stress control mode on cold-rolled Cu-Zr alloy sheets with various levels of tensile strength (TS). We then compared the fatigue properties of these sheets to those of cold-rolled Cu sheets. Fatigue life increased as TS increased. We separated our Cu-Zr sheets according to their mechanical strength levels, designating those with their TS ∼490 MPa as “H”, those with TS around 448 $ \pm $ 5 MPa as “M”, and those with TS < 440 MPa as “L”. The “H” sheets exhibited the longest life, followed by the “M” sheets, and the “L” sheets, all outperforming Cu. At 390 MPa. “H” Cu-Zr’s fatigue life was ∼3 times that of Cu. Both the Cu-Zr and the Cu showed cyclic hardening. The presence of Zirconium improved fatigue life by stabilizing microstructure and retarding the formation of cracks during fatigue cycling, thus positioning Cu-Zr alloys as much stronger candidates than Cu for resistive magnet conductors.
- 7 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Cu-Nb Conductors Under Cyclic Loading
Pulsed magnets in the US National High Magnetic Field Laboratory (MagLab) use rectangular cross-section Cu matrix composite conductors. The strongest of these conductors incorporate various combinations of Cu reinforced by Nb-fibers. The slip systems of Cu and Nb are markedly incompatible during deformation because Cu has a face-centered cubic structure while Nb has a body-centered cubic structure. In order to reach the level of strength that we required in our conductors, Cu-Nb was subjected to especially high levels of deformation strain. This high strain level, in combination with the aforementioned incompatibility of deformation systems, resulted in very high internal stress within both Cu and Nb that greatly affected the future deformation behavior of the resulting Cu-Nb conductors, as reflected in the stress-strain curves generated by our tests, particularly the cyclic loading tests. At cryogenic temperatures, the thermal expansion difference between Nb fibers and Cu matrix added additional internal stress in the resulting conductors. We studied the mechanical deformation behavior of Nb-fiber-strengthened Cu under cyclic loading, and we examined the relationship between the microstructure of these conductors and their deformation behavior.
- 7 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Cu-Nb Conductors Under Cyclic Loading
Pulsed magnets in the US National High Magnetic Field Laboratory (MagLab) use rectangular cross-section Cu matrix composite conductors. The strongest of these conductors incorporate various combinations of Cu reinforced by Nb-fibers. The slip systems of Cu and Nb are markedly incompatible during deformation because Cu has a face-centered cubic structure while Nb has a body-centered cubic structure. In order to reach the level of strength that we required in our conductors, Cu-Nb was subjected to especially high levels of deformation strain. This high strain level, in combination with the aforementioned incompatibility of deformation systems, resulted in very high internal stress within both Cu and Nb that greatly affected the future deformation behavior of the resulting Cu-Nb conductors, as reflected in the stress-strain curves generated by our tests, particularly the cyclic loading tests. At cryogenic temperatures, the thermal expansion difference between Nb fibers and Cu matrix added additional internal stress in the resulting conductors. We studied the mechanical deformation behavior of Nb-fiber-strengthened Cu under cyclic loading, and we examined the relationship between the microstructure of these conductors and their deformation behavior.
- Open Access
Comparison of Cu Strengthened by Ionic Bonded Particles and Cu Strengthened by Metallic Bonded Particles
Cu matrix composites, because of their high mechanical strength, are often used as conductors in high-performance electrical applications. These composites are manufactured through thermomechanical processing, which introduces a high density of particles that act as obstacles to dislocation motion. Increasing the density of these particles enhances the mechanical strength of the conductors, which we tested under static loading. Under cyclic loading, especially pulsed electrical mechanical loading, conductors may soften, harden, or even fail. Failure is likely to occur whenever the applied stress exceeds the flow stress of the conductors. Understanding and predicting the performance of conductors under cyclic loading can help researchers estimate the lifespan of any apparatus made from these conductors. The performance of conductors depends on whether the strengthening particles are characterized by ionic interatomic bonding or metallic bonding. During fabrication, we observed both the accumulation of dislocations and the dissolution of particles (which added more solute atoms to the matrix). Because both dislocations and solute atoms tend to migrate at room temperature or higher, the complexity of microstructure changes increases in composites under cyclic loading. To minimize such complexity, we designed our test to determine fatigue properties at 77 K. We subjected the conductors to cyclic fatigue tests using a load-controlled mode (the mode most commonly used in applications). This work sheds light on the correlation between tensile properties and fatigue properties in our composite conductors. We found that the correlation varied, depending on whether the conductors had been strengthened by ionic bond or metallic bond particles.
Open AccessComparison of Cu Strengthened by Ionic Bonded Particles and Cu Strengthened by Metallic Bonded Particles
Cu matrix composites, because of their high mechanical strength, are often used as conductors in high-performance electrical applications. These composites are manufactured through thermomechanical processing, which introduces a high density of particles that act as obstacles to dislocation motion. Increasing the density of these particles enhances the mechanical strength of the conductors, which we tested under static loading. Under cyclic loading, especially pulsed electrical mechanical loading, conductors may soften, harden, or even fail. Failure is likely to occur whenever the applied stress exceeds the flow stress of the conductors. Understanding and predicting the performance of conductors under cyclic loading can help researchers estimate the lifespan of any apparatus made from these conductors. The performance of conductors depends on whether the strengthening particles are characterized by ionic interatomic bonding or metallic bonding. During fabrication, we observed both the accumulation of dislocations and the dissolution of particles (which added more solute atoms to the matrix). Because both dislocations and solute atoms tend to migrate at room temperature or higher, the complexity of microstructure changes increases in composites under cyclic loading. To minimize such complexity, we designed our test to determine fatigue properties at 77 K. We subjected the conductors to cyclic fatigue tests using a load-controlled mode (the mode most commonly used in applications). This work sheds light on the correlation between tensile properties and fatigue properties in our composite conductors. We found that the correlation varied, depending on whether the conductors had been strengthened by ionic bond or metallic bond particles.
- 9 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Study of Delamination in REBCO Coated Conductor by Transmission Electron Microscopy
REBCO coated conductor has very promising applications as the conductor for high field magnets for particle accelerators and nuclear fusion reactors. One of its main failure modes is the delamination of its multilayer structure. Despite the decade-long efforts by the superconducting magnet community, the microscopic understanding of the delamination and the methods of mitigation are still lacking. This work presents the transmission electron microscopy (TEM) investigation of the microstructures of the Superpower Inc. REBCO coated conductor to correlate with its delamination strength. We looked into the microscopic cause of the buffer layer delamination of low delamination strength tape. We found that the low delamination strength tape primarily delaminated at MgO/Y2O3 interface, and it was due to nano-voids formed at the Y2O3 top surface adjacent to the IBAD MgO layer. Higher density nano-voids would reduce the MgO and Y2O3 contact area resulting in a weaker bonded interface. The dislocations with extra planes inserted at the REBCO/LaMnO3 interface also resulted in a weaker REBCO/ LaMnO3 interface.
- 9 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Study of Delamination in REBCO Coated Conductor by Transmission Electron Microscopy
REBCO coated conductor has very promising applications as the conductor for high field magnets for particle accelerators and nuclear fusion reactors. One of its main failure modes is the delamination of its multilayer structure. Despite the decade-long efforts by the superconducting magnet community, the microscopic understanding of the delamination and the methods of mitigation are still lacking. This work presents the transmission electron microscopy (TEM) investigation of the microstructures of the Superpower Inc. REBCO coated conductor to correlate with its delamination strength. We looked into the microscopic cause of the buffer layer delamination of low delamination strength tape. We found that the low delamination strength tape primarily delaminated at MgO/Y2O3 interface, and it was due to nano-voids formed at the Y2O3 top surface adjacent to the IBAD MgO layer. Higher density nano-voids would reduce the MgO and Y2O3 contact area resulting in a weaker bonded interface. The dislocations with extra planes inserted at the REBCO/LaMnO3 interface also resulted in a weaker REBCO/ LaMnO3 interface.
- Open Access
Study of delamination in REBCO coated conductor by transmission electron microscopy
Delamination strength of REBCO is very important for its applications in large magnet projects. This work presented the transmission electron microscopy (TEM) investigation of the microstructures of the REBCO coated conductor to understand its delamination property. We found that the low delamination strength is associated with nano-voids formed at the IBAD MgO/Y2O3 interface.
Open AccessStudy of delamination in REBCO coated conductor by transmission electron microscopy
Delamination strength of REBCO is very important for its applications in large magnet projects. This work presented the transmission electron microscopy (TEM) investigation of the microstructures of the REBCO coated conductor to understand its delamination property. We found that the low delamination strength is associated with nano-voids formed at the IBAD MgO/Y2O3 interface.
- 12 September 2024
- Published by Elsevier in Acta Materialia
- Vol. 281
Improvement of magnetic properties and hardness by alloying Mo to a FeCrCo alloy
- 12 September 2024
- Published by Elsevier in Acta Materialia
- Vol. 281
Improvement of magnetic properties and hardness by alloying Mo to a FeCrCo alloy
- Open Access
- 24 July 2024
- Published by Oxford University Press (OUP) in Microscopy and Microanalysis
- Vol. 30 (Supplement)
Study of a CuAg Alloy from Microscale to Atomic Scale
Cu-matrix composites containing Ag filaments exhibit both high strength and high conductivity [ 1, 2], making them particularly suitable for applications in high-field magnets [ 3]. This enhanced conductivity is attributed to the low solubility of Ag in Cu and vice versa. Additionally, their remarkable strength, which surpasses what would be expected from a simple rule-of-mixture calculation for Cu and Ag, is credited to the abundance of nanosized Ag fibers. These fibers predominantly originate from small silver particles within the as-cast composites. To achieve optimal properties in the final product, a detailed examination of the microstructure of the cast composites at the nanoscale or even atomic scale is essential [ 4]. Past investigations have revealed the complexity of the microstructure in Cu-Ag composites. Therefore, comprehensive characterization demands a thorough analysis of the microstructure in three dimensions (3D) and a deep understanding of the interfaces at the atomic level.
- 24 July 2024
- Published by Oxford University Press (OUP) in Microscopy and Microanalysis
- Vol. 30 (Supplement)
Open AccessStudy of a CuAg Alloy from Microscale to Atomic Scale
Cu-matrix composites containing Ag filaments exhibit both high strength and high conductivity [ 1, 2], making them particularly suitable for applications in high-field magnets [ 3]. This enhanced conductivity is attributed to the low solubility of Ag in Cu and vice versa. Additionally, their remarkable strength, which surpasses what would be expected from a simple rule-of-mixture calculation for Cu and Ag, is credited to the abundance of nanosized Ag fibers. These fibers predominantly originate from small silver particles within the as-cast composites. To achieve optimal properties in the final product, a detailed examination of the microstructure of the cast composites at the nanoscale or even atomic scale is essential [ 4]. Past investigations have revealed the complexity of the microstructure in Cu-Ag composites. Therefore, comprehensive characterization demands a thorough analysis of the microstructure in three dimensions (3D) and a deep understanding of the interfaces at the atomic level.