Changqing Hong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Changqing Hong has a total of 181 co-authors. Here are the top co-authors by number of shared publications:
Xinghong Zhang
27 shared publicationsCan Wu
AVIC Composite Corporation Ltd, Beijing, PR China
13 shared publicationsHebing Wang
11 shared publications- Xiangyu Jin
National Key Laboratory of Science and Technology on Advanced Composites in Special Environments Harbin Institute of Technology Harbin People's Republic of China
11 shared publications He Huang
9 shared publicationsWenbo Han
9 shared publications
Latest Publications
- 3 November 2026
- Published by Wiley in Advanced Functional Materials
Low‐Temperature Construction of Self‑Strengthening, Reusable, Ultralight Mullite Fiber Composites with Fish‑Scale‑Like Adaptive Boron‑Rich Layers
Reusable thermal protection materials are prone to structural damage accumulation and performance degradation under cyclic thermomechanical loading. Overcoming the conventional “cycling equals damage” paradigm is a critical challenge for long‐term service. Here, we exploit low‐temperature ceramization of a boron‐rich precursor at 600°C to in situ construct a fish‐scale‐like adaptive ceramic reinforcement layer (ACRL) on mullite fiber surfaces and junctions. The composite exhibits remarkable thermomechanical‐cycling‐induced strengthening (TMCIS) during cyclic compression at 420°C, with the average modulus nearly tripling after 100 cycles. In situ SEM reveals that thermomechanical coupling drives local displacement of adjacent fiber segments and node reconstruction; the ACRL of viscous softening acts as a dynamic “high‐temperature solder” that bridges fiber contacts and reconfigures the load‐transfer network, enabling a service‐induced strengthening mechanism. After 50 cycles (totaling 25 h) at 420°C, the mass loss per cycle is only 0.07%. Furthermore, the material simultaneously achieves a low density (0.29–0.35 g/cm 3 ), high compressive strength (1.60 MPa), and low thermal conductivity (0.062 W/(m·K)), realizing a synergy of lightweight, load‐bearing, and thermal insulation. This work converts cyclic loading from a damage source into a driving force for structural strengthening, establishing a new adaptive paradigm for long‐life reusable thermal protection materials.
- 3 November 2026
- Published by Wiley in Advanced Functional Materials
Low‐Temperature Construction of Self‑Strengthening, Reusable, Ultralight Mullite Fiber Composites with Fish‑Scale‑Like Adaptive Boron‑Rich Layers
Reusable thermal protection materials are prone to structural damage accumulation and performance degradation under cyclic thermomechanical loading. Overcoming the conventional “cycling equals damage” paradigm is a critical challenge for long‐term service. Here, we exploit low‐temperature ceramization of a boron‐rich precursor at 600°C to in situ construct a fish‐scale‐like adaptive ceramic reinforcement layer (ACRL) on mullite fiber surfaces and junctions. The composite exhibits remarkable thermomechanical‐cycling‐induced strengthening (TMCIS) during cyclic compression at 420°C, with the average modulus nearly tripling after 100 cycles. In situ SEM reveals that thermomechanical coupling drives local displacement of adjacent fiber segments and node reconstruction; the ACRL of viscous softening acts as a dynamic “high‐temperature solder” that bridges fiber contacts and reconfigures the load‐transfer network, enabling a service‐induced strengthening mechanism. After 50 cycles (totaling 25 h) at 420°C, the mass loss per cycle is only 0.07%. Furthermore, the material simultaneously achieves a low density (0.29–0.35 g/cm 3 ), high compressive strength (1.60 MPa), and low thermal conductivity (0.062 W/(m·K)), realizing a synergy of lightweight, load‐bearing, and thermal insulation. This work converts cyclic loading from a damage source into a driving force for structural strengthening, establishing a new adaptive paradigm for long‐life reusable thermal protection materials.
- Open Access
- 4 August 2026
- Published by Elsevier in SSRN Electronic Journal
Laser beam welding of (TiBw + (Ti,Zr)5Si3)/TA15 with two-scale network microstructure
Two-scale network-structured (TiBw + (Ti,Zr)5Si3)/TA15 titanium matrix composites exhibit high strength, good ductility, and excellent high-temperature performance. However, the presence of reinforcement particles adversely affects the weldability and may prompt crack initiation in welded joints. In this study, the laser beam welding of (TiBw + (Ti,Zr)5Si3)/TA15 was systematically investigated to reveal the effects of laser power (1100-1400 W) and welding speed (700-1000 mm·min-1) on weld formation, microstructure, and mechanical properties. Sound welded joints with full penetration and minimal pore defects were obtained within the investigated range. The welded joints consisted of base metal (BM), heat-affected zone (HAZ) and weld zone (WZ) without harmful interfacial debonding. Fine α' martensite formed in the HAZ and WZ, leading to a hardness distribution of WZ > HAZ > BM. The joint welded at 1100 W / 900 mm·min-1 exhibited the optimal comprehensive properties, with an ultimate tensile strength approximately 100 MPa higher than that of the as-received material and an elongation of 5.89%. All tensile fractures followed the microvoid coalescence mode. As the temperature rose from 600 °C to 700 °C, the fracture locations shifted from BM to WZ, and the equal-strength temperature was determined to lie between 675-700 °C. This work demonstrates the feasibility of laser beam welding for (TiBw + (Ti,Zr)5Si3)/TA15 within the investigated parameter range, providing a basis for its engineering application.
- 4 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessLaser beam welding of (TiBw + (Ti,Zr)5Si3)/TA15 with two-scale network microstructure
Two-scale network-structured (TiBw + (Ti,Zr)5Si3)/TA15 titanium matrix composites exhibit high strength, good ductility, and excellent high-temperature performance. However, the presence of reinforcement particles adversely affects the weldability and may prompt crack initiation in welded joints. In this study, the laser beam welding of (TiBw + (Ti,Zr)5Si3)/TA15 was systematically investigated to reveal the effects of laser power (1100-1400 W) and welding speed (700-1000 mm·min-1) on weld formation, microstructure, and mechanical properties. Sound welded joints with full penetration and minimal pore defects were obtained within the investigated range. The welded joints consisted of base metal (BM), heat-affected zone (HAZ) and weld zone (WZ) without harmful interfacial debonding. Fine α' martensite formed in the HAZ and WZ, leading to a hardness distribution of WZ > HAZ > BM. The joint welded at 1100 W / 900 mm·min-1 exhibited the optimal comprehensive properties, with an ultimate tensile strength approximately 100 MPa higher than that of the as-received material and an elongation of 5.89%. All tensile fractures followed the microvoid coalescence mode. As the temperature rose from 600 °C to 700 °C, the fracture locations shifted from BM to WZ, and the equal-strength temperature was determined to lie between 675-700 °C. This work demonstrates the feasibility of laser beam welding for (TiBw + (Ti,Zr)5Si3)/TA15 within the investigated parameter range, providing a basis for its engineering application.
- Open Access
- 9 February 2026
- Published by Springer Nature in Advanced Composites and Hybrid Materials
- Vol. 9 (2) , 109
Low-temperature hydrothermal synthesis of ultra-high-strength phenolic aerogel composites based on a physicochemical double-crosslinked network
- 9 February 2026
- Published by Springer Nature in Advanced Composites and Hybrid Materials
- Vol. 9 (2) , 109
Open AccessLow-temperature hydrothermal synthesis of ultra-high-strength phenolic aerogel composites based on a physicochemical double-crosslinked network
- 27 September 2025
- Published by Elsevier in Composites Communications
- Vol. 59
In-situ constructuring boron-modified phenolic aerogels with enhanced mechanical performance and flame retardancy
- 27 September 2025
- Published by Elsevier in Composites Communications
- Vol. 59
In-situ constructuring boron-modified phenolic aerogels with enhanced mechanical performance and flame retardancy
- 18 December 2024
- Published by Elsevier in Composites Part B: Engineering
- Vol. 292
Tough yet lightweight and flexible thermal insulative composite delivered by tendon-inspired gradient unit construction
- 18 December 2024
- Published by Elsevier in Composites Part B: Engineering
- Vol. 292
Tough yet lightweight and flexible thermal insulative composite delivered by tendon-inspired gradient unit construction
- 9 July 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (29) , 38520-38530
Significantly Enhanced Mechanical, Thermal, and Ablative Properties of the Lightweight Carbon Fabric/Phenol-Formaldehyde Resin/Siloxane Aerogels Ternary Interpenetrating Network
Lightweight ablative thermal protection materials (TPMs), which can resist long-term ablation in an oxidizing atmosphere, are urgently required for aerospace vehicles. Herein, carbon fabric/phenol-formaldehyde resin/siloxane aerogels (CF/PFA/SiA) nanocomposite with interpenetrating network multiscale structure was developed via simple and efficient sol-gel followed by atmospheric pressure drying. The ternary networks structurally interpenetrating in macro-, micron-, and the nanoscales, chemically cross-linking at the molecular scale, and silica layer generated by in situ heating synergistically bring about low density (∼0.3 g cm-3), enhanced mechanical properties, thermal stability, and oxidation resistance, and a low thermal conductivity of 81 mW m-1 K-1. More intriguingly, good thermal protection with near-zero surface recession at 1300 °C for 300 s and remarkable thermal insulation with a back-side temperature below 60 °C at 20 mm thickness. The interpenetrating network strategy can be extended to other porous components with excellent high-temperature properties, such as ZrO2 and SiC, which will facilitate the improvement of lightweight ablative TPMs. Moreover, it may open a new avenue for fabricating multifunctional binary, ternary, and even multiple interpenetrating network materials.
- 9 July 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (29) , 38520-38530
Significantly Enhanced Mechanical, Thermal, and Ablative Properties of the Lightweight Carbon Fabric/Phenol-Formaldehyde Resin/Siloxane Aerogels Ternary Interpenetrating Network
Lightweight ablative thermal protection materials (TPMs), which can resist long-term ablation in an oxidizing atmosphere, are urgently required for aerospace vehicles. Herein, carbon fabric/phenol-formaldehyde resin/siloxane aerogels (CF/PFA/SiA) nanocomposite with interpenetrating network multiscale structure was developed via simple and efficient sol-gel followed by atmospheric pressure drying. The ternary networks structurally interpenetrating in macro-, micron-, and the nanoscales, chemically cross-linking at the molecular scale, and silica layer generated by in situ heating synergistically bring about low density (∼0.3 g cm-3), enhanced mechanical properties, thermal stability, and oxidation resistance, and a low thermal conductivity of 81 mW m-1 K-1. More intriguingly, good thermal protection with near-zero surface recession at 1300 °C for 300 s and remarkable thermal insulation with a back-side temperature below 60 °C at 20 mm thickness. The interpenetrating network strategy can be extended to other porous components with excellent high-temperature properties, such as ZrO2 and SiC, which will facilitate the improvement of lightweight ablative TPMs. Moreover, it may open a new avenue for fabricating multifunctional binary, ternary, and even multiple interpenetrating network materials.
- 7 June 2024
- Published by Elsevier
- p. 459-475
Phenolic aerogels: Preparation, properties, and applications
- 7 June 2024
- Published by Elsevier
- p. 459-475
Phenolic aerogels: Preparation, properties, and applications
- 7 June 2024
- Published by Elsevier
Contributors