Ahfaz Ahmed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Ahfaz Ahmed has a total of 82 co-authors. Here are the top co-authors by number of shared publications:
- Subram Mani Sarathy
Clean Energy Research Platform, Physical Sciences and Engineering (PSE) Division, King Abdullah University of Science and Technology (KAUST), Thuwal 23955-6900, Saudi Arabia
13 shared publications - Jihad Badra
Saudi Aramco
7 shared publications - Aamir Farooq
King Abdullah University for Science and Technology (KAUST)
6 shared publications William L. Roberts
5 shared publications- Suk Ho Chung
King Abdullah Univ Sci & Technol, Clean Combust Res Ctr, Thuwal, Saudi Arabia
3 shared publications - Tamour Javed
Clean Combustion Research Center (CCRC), King Abdullah University of Science and Technology, Thuwal, Saudi Arabia
3 shared publications
Latest Publications
- Open Access
Detailed examination of the combustion of diesel and glycerol emulsions in a compression ignition engine
- 1 January 2019
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 37 (1) , 419-428
Small ester combustion chemistry: Computational kinetics and experimental study of methyl acetate and ethyl acetate
- 1 January 2019
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 37 (1) , 419-428
Small ester combustion chemistry: Computational kinetics and experimental study of methyl acetate and ethyl acetate
- 2 November 2018
- Published by Springer Nature
- p. 7-34
Combustion-Based Transportation in a Carbon-Constrained World—A Review
- 2 November 2018
- Published by Springer Nature
- p. 7-34
Combustion-Based Transportation in a Carbon-Constrained World—A Review
- 3 April 2018
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Numerical Simulations of High Reactivity Gasoline Fuel Sprays under Vaporizing and Reactive Conditions
Gasoline compression ignition (GCI) engines are becoming more popular alternative for conventional spark engines to harvest the advantage of high volatility. Recent experimental study demonstrated that high reactivity gasoline fuel can be operated in a conventional mixing controlled combustion mode producing lower soot emissions than that of diesel fuel under similar efficiency and NOx level [1]. Therefore, there is much interest in using gasoline-like fuels in compression ignition engines. In order to improve the fidelity of simulation-based GCI combustion system development, it is mandatory to enhance the prediction of spray combustion of gasoline-like fuels. The purpose of this study is to model the spray characteristics of high reactivity gasoline fuels and validate the models with experimental results obtained through an optically accessible constant volume vessel under vaporizing [2] and reactive conditions [3]. For reacting cases, a comparison of PRF and KAUST multi-component surrogate (KMCS) mechanism was done to obtain good agreement with the experimental ignition delay. From this study, some recommendations were proposed for GCI combustion modelling framework using gasoline like fuels.
- 3 April 2018
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Numerical Simulations of High Reactivity Gasoline Fuel Sprays under Vaporizing and Reactive Conditions
Gasoline compression ignition (GCI) engines are becoming more popular alternative for conventional spark engines to harvest the advantage of high volatility. Recent experimental study demonstrated that high reactivity gasoline fuel can be operated in a conventional mixing controlled combustion mode producing lower soot emissions than that of diesel fuel under similar efficiency and NOx level [1]. Therefore, there is much interest in using gasoline-like fuels in compression ignition engines. In order to improve the fidelity of simulation-based GCI combustion system development, it is mandatory to enhance the prediction of spray combustion of gasoline-like fuels. The purpose of this study is to model the spray characteristics of high reactivity gasoline fuels and validate the models with experimental results obtained through an optically accessible constant volume vessel under vaporizing [2] and reactive conditions [3]. For reacting cases, a comparison of PRF and KAUST multi-component surrogate (KMCS) mechanism was done to obtain good agreement with the experimental ignition delay. From this study, some recommendations were proposed for GCI combustion modelling framework using gasoline like fuels.
- 3 April 2018
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Standardized Gasoline Compression Ignition Fuels Matrix
Direct injection compression ignition engines running on gasoline-like fuels have been considered an attractive alternative to traditional spark ignition and diesel engines. The compression and lean combustion mode eliminates throttle losses yielding higher thermodynamic efficiencies and the better mixing of fuel/air due to the longer ignition delay times of the gasoline-like fuels allows better emission performance such as nitric oxides (NOx) and particulate matter (PM). These gasoline-like fuels which usually have lower octane compared to market gasoline have been identified as a viable option for the gasoline compression ignition (GCI) engine applications due to its lower reactivity and lighter evaporation compared to diesel. The properties, specifications and sources of these GCI fuels are not fully understood yet because this technology is relatively new. In this work, a GCI fuel matrix is being developed based on the significance of certain physical and chemical properties in GCI engine operation. Those properties were chosen to be density, temperature at 90 volume % evaporation (T90) or final boiling point (FBP) and research octane number (RON) and the ranges of these properties were determined from the data reported in literature. These proposed fuels were theoretically formulated, while applying realistic constraints, using species present in real refinery streams. Finally, three-dimensional (3D) engine computational fluid dynamics (CFD) simulations were performed using the proposed GCI fuels and the similarities and differences were highlighted.
- 3 April 2018
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Standardized Gasoline Compression Ignition Fuels Matrix
Direct injection compression ignition engines running on gasoline-like fuels have been considered an attractive alternative to traditional spark ignition and diesel engines. The compression and lean combustion mode eliminates throttle losses yielding higher thermodynamic efficiencies and the better mixing of fuel/air due to the longer ignition delay times of the gasoline-like fuels allows better emission performance such as nitric oxides (NOx) and particulate matter (PM). These gasoline-like fuels which usually have lower octane compared to market gasoline have been identified as a viable option for the gasoline compression ignition (GCI) engine applications due to its lower reactivity and lighter evaporation compared to diesel. The properties, specifications and sources of these GCI fuels are not fully understood yet because this technology is relatively new. In this work, a GCI fuel matrix is being developed based on the significance of certain physical and chemical properties in GCI engine operation. Those properties were chosen to be density, temperature at 90 volume % evaporation (T90) or final boiling point (FBP) and research octane number (RON) and the ranges of these properties were determined from the data reported in literature. These proposed fuels were theoretically formulated, while applying realistic constraints, using species present in real refinery streams. Finally, three-dimensional (3D) engine computational fluid dynamics (CFD) simulations were performed using the proposed GCI fuels and the similarities and differences were highlighted.
- 8 March 2018
- Published by Taylor & Francis in Combustion Science and Technology
- Vol. 190 (7) , 1218-1231
A surrogate fuel formulation to characterize heating and evaporation of light naphtha droplets
Light naphtha (LN) is gaining interest in internal combustion (IC) engine applications due to its low refining cost and higher heating values compared to commercial gasoline. To properly describe the chemical and physical behavior of the LN fuel under IC engine conditions, a systematic procedure to develop unified physical and chemical surrogates is described. The reduced component models to describe the chemical characteristics of LN are combined with the effective thermal conductivity/effective diffusivity (ETC/ED) model to represent the accurate evaporation behavior. Three surrogate fuels consisting of three to five components are presented and their performance in heating and evaporation of a single LN droplet is compared against the conventional primary reference fuel (PRF65) surrogate which is based on chemical aspects only. Unlike the previous approaches, the new surrogates also target matching the hydrogen-to-carbon ratio and research octane number in order to accurately describe the chemical behavior of the fuel. Subsequently, the performance of the surrogates in describing spray characteristics is tested by computational simulations compared with experimental measurements. The simulations were carried out using CONVERGE CFD package. The ETC/ED model was implemented into CONVERGE using user-defined functions. The predicted spray penetration length for the developed surrogates shows good agreement with the experimental data. At engine-like conditions, the ETC/ED model predicts higher vapor mass than the infinite thermal conductivity/infinite diffusivity model, hence showing the expected trend by incorporating the realistic droplet heating process.
- 8 March 2018
- Published by Taylor & Francis in Combustion Science and Technology
- Vol. 190 (7) , 1218-1231
A surrogate fuel formulation to characterize heating and evaporation of light naphtha droplets
Light naphtha (LN) is gaining interest in internal combustion (IC) engine applications due to its low refining cost and higher heating values compared to commercial gasoline. To properly describe the chemical and physical behavior of the LN fuel under IC engine conditions, a systematic procedure to develop unified physical and chemical surrogates is described. The reduced component models to describe the chemical characteristics of LN are combined with the effective thermal conductivity/effective diffusivity (ETC/ED) model to represent the accurate evaporation behavior. Three surrogate fuels consisting of three to five components are presented and their performance in heating and evaporation of a single LN droplet is compared against the conventional primary reference fuel (PRF65) surrogate which is based on chemical aspects only. Unlike the previous approaches, the new surrogates also target matching the hydrogen-to-carbon ratio and research octane number in order to accurately describe the chemical behavior of the fuel. Subsequently, the performance of the surrogates in describing spray characteristics is tested by computational simulations compared with experimental measurements. The simulations were carried out using CONVERGE CFD package. The ETC/ED model was implemented into CONVERGE using user-defined functions. The predicted spray penetration length for the developed surrogates shows good agreement with the experimental data. At engine-like conditions, the ETC/ED model predicts higher vapor mass than the infinite thermal conductivity/infinite diffusivity model, hence showing the expected trend by incorporating the realistic droplet heating process.
- Open Access
- 1 March 2018
- Published by Elsevier in Combustion and Flame
- Vol. 189, 337-346
Autoignition of straight-run naphtha: A promising fuel for advanced compression ignition engines
- 1 March 2018
- Published by Elsevier in Combustion and Flame
- Vol. 189, 337-346
Open AccessAutoignition of straight-run naphtha: A promising fuel for advanced compression ignition engines
- Open Access
- 1 December 2017
- Published by Elsevier in Combustion and Flame
- Vol. 186, 114-128
Autoignition characteristics of oxygenated gasolines
- 1 December 2017
- Published by Elsevier in Combustion and Flame
- Vol. 186, 114-128
Open AccessAutoignition characteristics of oxygenated gasolines