TKToshiharu Katayama

Toshiharu Katayama

*This is an algorithmically generated author record based on publicly available information.

Toshiharu Katayama has a total of 15 co-authors. Here are the top co-authors by number of shared publications:

  • F. Yano

    Department of Electrical and Electronic Engineering, Tokyo Institute of Technology 4 , Meguro, Tokyo 152-8552, Japan

    2 shared publications
  • K. Inoue

    Institute for Materials Research, Tohoku University 1 , Oarai, Ibaraki 311-1313, Japan

    2 shared publications
  • M. Inoue

    Device Technology Division, Renesas Electronics Corporation 3 , Hitachinaka, Ibaraki 312-8504, Japan

    2 shared publications
  • T. Ide

    Technology Division, Renesas Semiconductor Manufacturing Co., Ltd. 2 , Hitachinaka, Ibaraki 312-8504, Japan

    2 shared publications
  • Y. Kunimune

    Technology Division, Renesas Semiconductor Manufacturing Co., Ltd. 2 , Hitachinaka, Ibaraki 312-8504, Japan

    2 shared publications
  • Y. Shimada

    Technology Division, Renesas Semiconductor Manufacturing Co., Ltd. 2 , Hitachinaka, Ibaraki 312-8504, Japan

    2 shared publications

Latest Publications

  • Effect of carbon on boron diffusion and clustering in silicon: Temperature dependence study

    by Y. Tu, Y. Shimizu, Y. Kunimune, Y. Shimada, T. Katayama, T. Ide, M. Inoue, F. Yano, K. Inoue, Y. Nagai

    Atom probe tomography and secondary ion mass spectrometry were used to investigate the effects of carbon (C) co-implantation and subsequent annealing at 600 to 1200 °C on the behavior of implanted boron (B) atoms in silicon. When B alone was implanted, annealing at 600 to 800 °C caused it to form clusters in the peak region (1020 cm−3) of the concentration profile, and diffusion only occurred in the low-concentration tail region (18 cm−3), which is thought to be the well-known transient enhanced diffusion. However, when co-implantation with C was performed, this diffusion was almost completely suppressed in the same annealing temperature range. In the absence of C implantation, annealing at 1000 °C caused B clusters to begin to dissolve and B to diffuse out of the peak concentration region. However, this diffusion was also suppressed by C implantation because C atoms trapped B atoms in the kink region found at the B concentration level of 2 × 1019 cm−3. At 1200 °C, B clusters were totally dissolved and a strong B diffusion occurred. In contrast to lower annealing temperatures, this diffusion was actually enhanced by C implantation. It is believed that Si interstitials play an important role in the interaction between B and C. This kind of comprehensive investigation yields important information for optimizing ion implantation and annealing processes.


  • Blocking of deuterium diffusion in poly-Si/Al2O3/HfxSi1−xO2/SiO2 high-k stacks as evidenced by atom probe tomography

    by Y. Tu, B. Han, Y. Shimizu, Y. Kunimune, Y. Shimada, T. Katayama, T. Ide, M. Inoue, F. Yano, K. Inoue, et al.

    Hydrogen (H) plays an important role in determining the reliability and performance of HfO2- and Al2O3-based high-k dielectric electronic devices. In order to understand H behavior, deuterium (D), an isotope of H, was introduced into the poly-Si cap of Al2O3/HfxSi1−xO2/SiO2 high-k stacks by ion implantation. Atom probe tomography was used to image the D distribution in samples annealed under different conditions. The results clearly demonstrated that the D atoms were trapped at the interface of poly-Si and Al2O3 after annealing at 900 K for 10 min. Thus, it is possible that Al2O3 blocks the H atoms at the surface, preventing them from diffusing into the high-k dielectrics during the H2 annealing process in current fabrication technology. The current work also exhibits an example of investigating H behavior in semiconductors by atom probe tomography.


  • Guest Editorial Special Section on the 2016 International Symposium on Semiconductor Manufacturing

    by Toshiharu Katayama

    Since its start in 1992 in Japan, the International Symposium on Semiconductor Manufacturing (ISSM) has provided unique opportunities to share the best practices of semiconductor manufacturing technologies for professionals worldwide. At the symposium, professionals assemble to discuss the technologies developed to meet worldwide requirements for advanced semiconductor manufacturing. It is crucial to re-examine semiconductor manufacturing in terms of fundamental principles to improve the performance of devices. In addition, manufacturing technologies that preserve the Earth’s environment will require new concepts and stronger collaborative efforts to find precompetitive solutions to the challenges posed.

  • Kikuchi-Band Analysis of X-Ray Photoelectron Diffraction Fine Structure of Si(100) by Precise Angle-Resolved X-Ray Photoelectron Spectroscopy

    by Toshiharu Katayama, Hidekazu Yamamoto, Yoji Mashiko, Hiroshi Koyama, Satoru Kawazu, Masataka Umeno

    X-ray photoelectron diffraction fine structure of Si(100) is studied with precise angle-resolved X-ray photoelectron spectroscopy. Polar-angle intensity distributions of the Si 2p photoelectron emission excited by Al Kα X-rays are measured from H-terminated Si(100) along some azimuthal angles, and are qualitatively interpreted using both forward-focusing peaks along zone axes and Kikuchi bands associated with planes of low indices ({220}, {400}, {111} and {311}). To confirm the interpretation experimentally, we prepare ultrathin Si(100) layers on SiO2 from silicon-on-insulator (SOI) wafers. The thicknesses of the ultrathin Si(100) layers are adjusted so that the SOI layer is thick enough to exhibit the forward-focusing peak along [100] but slightly thinner than the thickness in which the contribution of the Kikuchi pattern weakens. It is observed experimentally, for the first time, that the intensities of X-ray photoelectron diffraction fine structure due to Kikuchi lines decreases for such ultrathin Si(100), while the forward-focusing peak remains unchanged, as expected from our interpretation.